DSM 6.1.x Loader


Recommended Posts

11 hours ago, waspsoton said:

check this post out. I am currently running the latest update on my amd system.

 

 

Thanks, but my Nas is built on a regular commercial AMD mobo (Gigabyte) not HP N54L. And therefore I couldn't find C1E in the Bios to disable it. So, how?

Link to post
Share on other sites

Hi,

 

Since i have updated to 6 and 6.1 I can't reboot the syno. It shutdown but when it restart the syno show booting kernel but nothing more, I have to manually sutdown and start.

 

Do you have an any? Which file log can I check to debug? It is possible to activate bootloader verbose?

 

I have an HP n54l (amd turion).

 

Thanks

Link to post
Share on other sites
On 04/08/2017 at 6:48 AM, lunzet said:

 

not getting your point. why not? its working fine see my signature

I am running this on an asrock a75-hvs motherboard. I didn't even look for the c1 option. But it installed without any problems 

Link to post
Share on other sites

Hello,

First of all a big thank you to all the members of this forum.

I have an Abit ip35 pro without UEFI and I am in version dsm 6.02 with the loader: jun-intel-baremetal-hybrid-uefibios-arcao-v1 and all works wonderfully.

I would like to go in dsm 6.1 but the loader DS3615xs 6.1 Jun's Mod V1.02 is in UEFI mode and my sandick usb key is not recognized by the non-UEFI BIOS

Is there a hybrid loader for the dsm 6.1?

cordially

Edited by Onkyo83
Link to post
Share on other sites
1 hour ago, Onkyo83 said:

Hello,

First of all a big thank you to all the members of this forum.

I have an Abit ip35 pro without UEFI and I am in version dsm 6.02 with the loader: jun-intel-baremetal-hybrid-uefibios-arcao-v1 and all works wonderfully.

I would like to go in dsm 6.1 but the loader DS3615xs 6.1 Jun's Mod V1.02 is in UEFI mode and my sandick usb key is not recognized by the non-UEFI BIOS

Is there a hybrid loader for the dsm 6.1?

cordially

Hi! Could  you please tell me where can I found the jun-intel-baremetal-hybrid-uefibios-arcao-v1 loader? I would try it... 

Thanks! 

Link to post
Share on other sites

I have DSM 6.0.2 running Jun loader on Esxi 6.0 with a smaller 24 mb vmdk that is boot drive (disk 1) and larger vmdk hard drive (disk 2) that contains data and apps. I am trying to upgrade to DSM 6.1 with v1.02b DS3615xs. I can get the virtual machine to boot but I get a message no hard drive installed even though the vmdk hard drive that contains data and apps is connected as disk 2 with v1.02b drive as disk 1. I am not sure what has changed ? Any help is greatly appreciated.

Link to post
Share on other sites
On 2017/7/26 at 6:00 AM, neotronic said:


I have it working in Hyper-V. Not sure if It's 1.02b though. I converted the img to vhd and set it as the 1st drive. Hope it helps.

Hi, I currently using VirtualBox and want to upgrade from 6.0.2 to 6.1.3 but after replacing the old loader with the new 1.02b iso loader, it didn't boot up, what can I do?

Thanks

Link to post
Share on other sites

Hi, 

 

I have some issue with my xpenology, specially with my RAID Controller, it is a Startech PCISATA4R1, since I updated my xpenology from 5.2-5644 to 6.1.3-15152 update 1 ( with jun loader 1.02b), my xpenology don’t recognize the disk witch are plugged to my RAID controller. I have done some search but I didn’t see a solution to fix my problem.

 

Someone can help me ? 

 

Thanks in advance ^^

Link to post
Share on other sites

@Polanskiman & @jun

 

Thanks to you both :smile: I have updated from Loader v1.01 to v1.2b on an HP MicroServer Gen8.

 

Things i noticed is the Partitions are now different and you only need to Modify the 1 for the grub file. The extra file i did first did not work so i saw the post to do not use it an it works as is :smile: 

 

DSM Downloaded From DSM 6.1.3 Update 15152

 

I used jun's Loader  v1.2b DS3615

 

The issue i have is that Package Intrusion Prevention no longer works. It is asking me to uninstall it and suggestions ?

 

Other then that all seems to be ok all Data, Files & Settings are there. Now to test Update 1.

 

Thanks Again

Link to post
Share on other sites
1 hour ago, sylvo95 said:

Hi, 

 

I have some issue with my xpenology, specially with my RAID Controller, it is a Startech PCISATA4R1, since I updated my xpenology from 5.2-5644 to 6.1.3-15152 update 1 ( with jun loader 1.02b), my xpenology don’t recognize the disk witch are plugged to my RAID controller. I have done some search but I didn’t see a solution to fix my problem.

 

Someone can help me ? 

 

Thanks in advance ^^

Startech PCISATA4R1 = Silicon Image 3114 =sata_sil.ko

as this module does not start anymore with actual 6.1.3 there is litte that can be doen now until synology releases kernel sources for 6.1.x, the only source availible is 6.1.(0) aka 6.1_15047

i documented this in my "driver extension" 6.1 extra.lzma here in a thread

  • Like 1
Link to post
Share on other sites
7 hours ago, eric1357a said:

Hi, I currently using VirtualBox and want to upgrade from 6.0.2 to 6.1.3 but after replacing the old loader with the new 1.02b iso loader, it didn't boot up, what can I do?

Thanks

you put in the "right" mac adress in the vm's configuration (the mac adress in the grub.cfg has to be placed in the vm's nic configuration

you know about this?

https://xpenology.club/install-dsm-6-1-on-virtualbox/

Link to post
Share on other sites
20 minutes ago, IG-88 said:

Startech PCISATA4R1 = Silicon Image 3114 =sata_sil.ko

as this module does not start anymore with actual 6.1.3 there is litte that can be doen now until synology releases kernel sources for 6.1.x, the only source availible is 6.1.(0) aka 6.1_15047

i documented this in my "driver extension" 6.1 extra.lzma here in a thread

Thank you for your answer, so I just have to downgrade to 6.1_15047 to make it work ?

Link to post
Share on other sites
11 hours ago, Vodka2014 said:

@Polanskiman & @jun

 

Thanks to you both :smile: I have updated from Loader v1.01 to v1.2b on an HP MicroServer Gen8.

 

Things i noticed is the Partitions are now different and you only need to Modify the 1 for the grub file. The extra file i did first did not work so i saw the post to do not use it an it works as is :smile: 

 

DSM Downloaded From DSM 6.1.3 Update 15152

 

I used jun's Loader  v1.2b DS3615

 

The issue i have is that Package Intrusion Prevention no longer works. It is asking me to uninstall it and suggestions ?

 

Other then that all seems to be ok all Data, Files & Settings are there. Now to test Update 1.

 

Thanks Again

 

HEY VODka!

May I ask where can I find the loader update tutorial?

thanks so MUCH!

Link to post
Share on other sites
16 minutes ago, neverwinboy said:

So…you mean just switch to the 1.02b version synboot.img file?that's all?

 

1. Download v1.02b DS3615

2. Follow the steps with OSFMount

3. Select Partition 0 (15MB)

4. Copy the settings from your old grub.cfg to the new grub.cfg based on what was stated in this guide that you need to update on Page 1 etc.... there is an grub folder on this partition. I did not use extra.lzma ramdisk which is on Partition 1 for this build it seems.

5. Then i deleted the Partitions on my SD Card and followed Step 6

6. Step 7 i left out since this was done already when i used v1.01. The part like adding your SD Card to you machine that was done :smile:

7. Step 8 It boots up as stated since i have an Intel machine

8. It took some time and then i saw my device with the Synology Assistant. I clicked on the MIGRATE ONE  Install, Migration, Selected the .pat that i downloaded (MAKE SURE YOU SELECT MIGRATE OR YOU WILL WIPE THE DATA. JUST READ THE STEPS)

9. Once all done checked my machine updated to Update 1 and rebooted for an second time to be 100% Sure

 

Hope this works for you as well.

Edited by Vodka2014
Change
Link to post
Share on other sites
1 minute ago, Vodka2014 said:

 

1. Download v1.02b DS3615

2. Follow the steps with OSFMount

3. Select Partition 0 (15MB)

4. Copy the settings from your old grub.cfg to the new grub.cfg based on what was stated in this guide that you need to update on Page 1 etc.... there is an grub folder on this partition. I did not use extra.lzma ramdisk which is on Partition 1 for this build it seems.

5. Then i deleted the Partitions on my SD Card and followed Step 6

6. Step 7 i left out since this was done already when i used v1.01. The part like adding your SD Card to you machine that was done :smile:

7. Step 8 It boots up as stated since i have an Intel machine

8. It took some time and then i saw my device with the Synology Assistant. I clicked on the MIGRATE ONE  Install, Migration, Selected the .pat that i downloaded

9. Once all done checked my machine updated to Update 1 and rebooted for an second time to be 100% Sure

 

Hope this works for you as well.

oh…I'm using vmware workstation,what should I do ?Is there any tutorial for Vmware?

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.