DSM 6.1.x Loader


Recommended Posts

Hey guys,

 

After reading all these pages, I'm still a little confused about whether or not I should update.  Configuration- Loader v1.02a, baremetal, Btrfs volume on 6.1-15047 Update 2.  Can I safely update to 6.1.2-15132?

 

Thanks!

Link to post
Share on other sites

Confirmed, upgrading VIA GUI from 6.1.1-15101 Update 4 to 6.1.2-15132 worked without issues. 

My sys spec:

Install: Bare Metal

Loader: DS3617xs v1.02a2.

Motherboard: Supermicro X10SLH-F BIOS Revision:  R 3.0a

RAM:32Gb ECC ram

CPU: XEON E3-1276 v3

HBA: SAS 9211-8i flashed to it mode firmware P20

Volume SHR2

Uptime: 13 hours. 

So far so good however the system was running for only 13+ hours. Will report if anything not working correctly.

Link to post
Share on other sites
On 15/6/2017 at 4:21 PM, Arcao said:

Damn, I can't edit my previous post. :-o

Anyway, after copy kernel modules from extra.lzma to /lib/modules, it works again! So it looks like missing kernel modules detection is not present in a bootloader.

I have same issue with my HP gen8. I'm newbe, please, can you help me? Many thanks!

Link to post
Share on other sites
2 hours ago, m3rlinux said:

I have same issue with my HP gen8. I'm newbe, please, can you help me? Many thanks!

I managed to solve :smile:
I managed to access to virtual serial console following instructions found in this thread.
So, I had login into my NAS and by "sudo -i" I had root access.

After that I did these two commands
 

cp /lib/modules/update/libphy.ko /lib/modules/
cp /lib/modules/update/tg3.ko /lib/modules/

finally I rebooted DSM and Networ starting working again.
I apologyze my poor english.

Link to post
Share on other sites
Hi guys,
I tried to update my NAS (ds3617ds Jun's 1.02a2) from DSM 6.1.1-15101 Update 4 to DSM 6.1.2-15132 without luck, no lan. Fortunately I have serial cable connected to my router so I am able to debug it. Anyway the update removed all custom kernel drivers which was copied while initial installation. The modified rc and rc.modules are present, kernel modules and firmwares not. I tried also run reinstall bootloader choice, but it doesn't resolve missing kernel modules.
Last chance is to copy missing kernel modules manually with second USB drive.

its an old script bug due to my oversight, I am uploading a new version to fix it, hopefully without introduce new bugs :smile:
  • Like 8
Link to post
Share on other sites
6 hours ago, jun said:


its an old script bug due to my oversight, I am uploading a new version to fix it, hopefully without introduce new bugs :smile:

 

 

Thanks! Will the new loader be able to support DSM 6.1.2-15132 (as clean install) on ESXi 6.5?! :smile:

Link to post
Share on other sites
3 minutes ago, meimeiriver said:

 

Sorry, missed that. I thought I saw someone say it worked on bare metal.

 

clean install works on all configurations(bare metal and ESX ). my test lab it's on vmware 12 + esx 5 + esx 6 + esx 6.5:)

 

 

Edited by foxbat
  • Like 1
Link to post
Share on other sites
8 hours ago, jun said:


its an old script bug due to my oversight, I am uploading a new version to fix it, hopefully without introduce new bugs :smile:

@jun, is it 1.02b? It seem it cannot boot up for ds3617 in baremetal, always said migratable. Even, I use it for new install, it still got the same issue.

 

Use back 1.02a2, no problem on clean installation, 6.11 or 6.12

Link to post
Share on other sites
14 hours ago, foxbat said:

esx 6.5. update fail. fresh install 6.1.2 ok

Same here.
update crash my DSM.

I made a clean install.

 

Someone does know why update fails with ESXI ?
 

But my volume is crashed without repair option, never see this message, and all datas are available....

 

 

 

Link to post
Share on other sites

I really dont understand how this guys from Synology think! I did the update DSM 6.1.2-15132  from 6.1.1. bare metal.

Not succesful. Ok, no biggie. I just reinstall the DSM, the data partition is safe, right?

And here it comes, the setup page says: "please click Recover if you want to recover your data and settings now."

But what if i dont want to recover? If i want to start anew?  What other button is there to push? None!

Any ideeas?

Link to post
Share on other sites

Hi all,

 

I just used V1.02a for an ESXi install after an update that upset the DSM and complained of a recovery mode.

 

Whatever...

 

I used the V1.02 and installed from scratch and it seems like it's running the latest version now: 

 

Current DSM version:    DSM 6.1.2-15132

 

Now, my problem is that I can't create volumes, even though I've edited the synoinfo.conf file and enabled SHR:

 

support_syno_hybrid_raid="yes"

 

Any suggestions?

DSMvol.PNG

Link to post
Share on other sites
5 hours ago, fitman said:

@jun, is it 1.02b? It seem it cannot boot up for ds3617 in baremetal, always said migratable. Even, I use it for new install, it still got the same issue.

 

Use back 1.02a2, no problem on clean installation, 6.11 or 6.12

Sorry, fixed

Link to post
Share on other sites
2 hours ago, jun said:

Sorry, fixed

 

Would you be able to produce a build for AMD N54L please :smile: - the experimental version you did for 1.01 worked so would it be possible to apply them to your new loader?

 

If not could you provide more information on what you did to produce that loader so we can look at spinning our own release?

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.