CtrlAltDel Posted November 13, 2016 Share #1201 Posted November 13, 2016 Sorry I am new here, can I use this loader with my N54L? 從我的iPhone使用Tapatalk 發送 Yes, read this thread > viewtopic.php?f=2&t=22100 and the OP of this thread > viewtopic.php?f=2&t=20216 Quote Link to comment Share on other sites More sharing options...
lord_kimbou Posted November 13, 2016 Share #1202 Posted November 13, 2016 I update from 5.2 to 6.0.2 Up3. I used last loader v1.01 on USB only.. I have Amd Cpu integrated mainboard QC5000-ITX/PH, and apparently all is working!! Lan is Ok, Programs works Ok, 3 Sata disk working Ok, total memory is Ok too.. Do you want some additional test?? I'm a little noob on this, but if you guide me, I can do it! Quote Link to comment Share on other sites More sharing options...
xtiang7c0 Posted November 13, 2016 Share #1203 Posted November 13, 2016 Hey guys, if I want to edit and repack the synoboot.img to use it in my unRAID VM, what Software do I use? In 7 Zip I can´t edit the file as it´s read only mode. I´d like to change the MAC/SN in grub.cfg. Thanks Christian Hi, try this http://www.osforensics.com/tools/mount-disk-images.html It works! Fantastic. Thank you Quote Link to comment Share on other sites More sharing options...
dh4736 Posted November 13, 2016 Share #1204 Posted November 13, 2016 First of all - many thanks for the work which has gone into this - I currently using a DSM 5.2 for quite a while and just tried to migrate to 6 using 1.01 loader. By the looks my network drivers seem missing though - I am using an Asus P5N7A mainboard. Any help in how I can add the needed drivers would be gr8. Thx dh4736 Quote Link to comment Share on other sites More sharing options...
easytech Posted November 13, 2016 Share #1205 Posted November 13, 2016 Hi Community, I created a simple video to show the beginner how to prepare the Synoboot.img bootable device and also how to find your pendrive VID and PID. Below is the youtube link. Hope this will help the beginner on the preparation. Thank you. Jason EasyTech Thank you so much mate :- that was a big help for a noob like me. Can I use the same method to upgrade (not a fresh install) from DSM 5.2-5644 on a barmetal mini computer (lenovo M700) to DSM 6.0.2 without data loss on the SSD ? Thanx in advnced Common guys cant wait for one to confirm the above - holding back couse of my lack of experience- Hope some one who knows if I preb. the USB with the latest boot image ver. 1.0.1 and install the DSM 6.0.2 over DSM 5.2-5644 will it merge my existing data on the HD and I can continue where I left off when it was on DSM 5.2 ? PC= lenovo M700 tiny. Thanx Hi boOmLa, Yes, please follow the tutorial that shared by Dfds. viewtopic.php?f=2&t=22100 I did a testing on my another machine, 5.2 - 6.0 without problem. However, still recommend you to back up the data and configuration file. Also please make sure your computer have all the driver packed inside the Synoboot.img Thank you. Regards, Jason EasyTech Quote Link to comment Share on other sites More sharing options...
vikino Posted November 13, 2016 Share #1206 Posted November 13, 2016 Hi all, anyone tryied to import VM into QNAP Virtualization Station? Im getting this error: (0.00/100%)\\rqemu-img: Could not open /share/CACHEDEV1_DATA/VirtualPC/Syno6/DS3615xs/synoboot.vmdk: Invalid extent lines:RW 102400 VMFS synoboot.img 0# The Disk Data Base #DDBddb.adapterType = lsilogicddb.deletable = trueddb.encoding = UTF-8ddb.longContentID = 7e24a756b77e33e24ac940cc6ccf51e5ddb.thinProvisioned = 1ddb.uuid = 60 00 C2 9a ee da ca 33-df 5e 04 3f 80 55 f9 62ddb.virtualHWVersion = 10 When i create own virtual machine without importing and then try to start i get this: (0x1) internal error: process exited while connecting to monitor: 2016-11-13T12:42:09.320176Z qemu-system-x86_64: -drive file=/share/CACHEDEV1_DATA/VirtualPC/Syno6/DS3615xs/synoboot.img,if=none,id=drive-ide0-0-0,format=qcow2,cache=writeback: Image is not in qcow2 format . Image is not in qcow2 format? Thanks for any suggestions, Vitek EDIT: Figured it out... First what is needed is to modify .vmx file, because VMware ESXi does not support HW version 12, just edit it to 11 or 10. Then there is no prolem to import it to ESXi and afterwards export OVF template. I exported it as OVA and imported do Qnap. If anyone is interrested i can share link with ova. Quote Link to comment Share on other sites More sharing options...
webbyboy Posted November 13, 2016 Share #1207 Posted November 13, 2016 Works for me too on N54L with 5 Disks... Updted from 5.2 to 6.03 with this loder... Hi did you set anything on the grub.cfg for SataPortMap=? Quote Link to comment Share on other sites More sharing options...
vikino Posted November 13, 2016 Share #1208 Posted November 13, 2016 It is possible to convert IMG to ISO? I tryied to convert it by imgtoiso and it does not recognises filesystem Vitek Quote Link to comment Share on other sites More sharing options...
boOmLa Posted November 13, 2016 Share #1209 Posted November 13, 2016 Have you actually tried searching the forums, if you had you would have found your answer: viewtopic.php?f=2&t=22100 Tahnk you very much Quote Link to comment Share on other sites More sharing options...
boOmLa Posted November 13, 2016 Share #1210 Posted November 13, 2016 Test i did : I build a VM with XPEnoboot_DS3615xs_5.2-5967.1, and install the latest compatible version of DSM. Then, i create 4 disk of 10 Go, and use RAID5 to create 1 volume. I copy fiew thing inside the Volume (2630 files, 265 folder, 4.3 Go). Now it's time to "upgrade"... So i shutdown the VM (in fact, shutdown the NAS from the web interface), then i copy all new file from BootLoader V1.01, edit the VM setting and manually added existing VMDK (Disk1 to 4) ... In the non-VmWorld.. it's like create a new USB drive, and boot from it ! Then i use the "find.synology.com", Click on "install" and "migration", and manual install the new version of DSM (dowloaded from Synology Website). Once reboot, i log into the new NAS. My old password was still working ! And the "Test" folder i create inside was still there ! I did that because when i update my DS410 from DSM4 to DSM5, it change a lot (like the file format from ext2or3 to ext4). I was thinking that i lost all of my data... but it was not the case, the Volume was still there. Only lost all setting from the NAS (username, installed package,...). So i re-create the username, then added to me the right to see all Shared folder that was not visible ... and everyhting return to normal ! What you have done here is very very much appreciated - really BIG thanx to find time to build at test environment to help - BIG thanx mate and keep up the good work and spirit Quote Link to comment Share on other sites More sharing options...
boOmLa Posted November 13, 2016 Share #1211 Posted November 13, 2016 Hi boOmLa, Yes, please follow the tutorial that shared by Dfds. viewtopic.php?f=2&t=22100 I did a testing on my another machine, 5.2 - 6.0 without problem. However, still recommend you to back up the data and configuration file. Also please make sure your computer have all the driver packed inside the Synoboot.img Thank you. Regards, Jason EasyTech Hay Jason, thanx for the reply mate - I did forllow the youtube video and Dfds tutorial... Now I'am on DSM 6.0.2 One thing I've encountered when updating from http://find.synology.com/ (browser)- keept getting error like no disk were found and serial port disabled ... I used the synology assistent and wverything went great no prob. Big thanx for all your help guys Quote Link to comment Share on other sites More sharing options...
nols Posted November 13, 2016 Share #1212 Posted November 13, 2016 It is possible to convert IMG to ISO? I tryied to convert it by imgtoiso and it does not recognises filesystem Vitek Yes. Starwind V2V Converter works. You can boot with Hyper-V, but it hangs because of no network drivers... Quote Link to comment Share on other sites More sharing options...
nols Posted November 13, 2016 Share #1213 Posted November 13, 2016 It is possible to convert IMG to ISO? I tryied to convert it by imgtoiso and it does not recognises filesystem Vitek Yes. Starwind V2V Converter works. You can boot with Hyper-V, but it hangs because of no network drivers... Quote Link to comment Share on other sites More sharing options...
lazygatto Posted November 13, 2016 Share #1214 Posted November 13, 2016 I Update whit Jun 1.0.1 and its working fine everything Just a quick question DSM 6.0.2-8451 Update 3 is available, someone know if its safe to update? Updated successfully 2 VMs on eSXI and Proxmox Quote Link to comment Share on other sites More sharing options...
hehe8899 Posted November 14, 2016 Share #1215 Posted November 14, 2016 (edited) I've recently annouce that my work on a kernel mode dynamic patcher in this post .... How to install: find the vid/pid of your usb drive Burn the image to the drive, optionally edit grub.cfg to set vid/pid and boot entry, OR connect monitor/keyboard/serial console to your Box. Press C during Grub boot menu to enter command line vid 0xXXXX pid 0xYYYY to configure pid and vid ("pid" and "vid" are command, and "XXXX", "YYYY" are you usb drive's vid,pid) (There are a few other options can be config this way, you can read grub.cfg to know more detail.) Press Esc to go back to boot menu Select baremeta/baremetal AMD entry, press enter to boot. If your encounter the "disk port disabled" error during installation, try the force install menu entry. if both option does not work, you have to fallback to SataPortMap method, type this line in grub command line, replace XX with appropriate value. append SataPortMap=XX 11/2: as I promised, here is v1.01, download link is the same as v1.0 This update contains nothing fancy, mainly for inner peace, Plus, I revert megaraid_sas mpt3sas to old version. It's not shining new now, the title is obsolete My HP Microserver Gen8 can't boot by U-disk burned in your loader v1.01 as your indicate above. It shows "Non system disk" but works well with 5.2 XPEnoboot_DS3615xs_5.2-5644.5 from this forum. As I known, Gen8 can't boot by UEFI mode. Any suggestions? update: The U-disk above was unstable and my Gen8 was updated to DSM 6.0.2 with new U-sidk by your loader v1.01. Thanks! Edited November 14, 2016 by Guest Quote Link to comment Share on other sites More sharing options...
djelusion Posted November 14, 2016 Share #1216 Posted November 14, 2016 does anyone have a link to dsm 6.0 pat file?. looks like this is working... but i dont have a pat file. Quote Link to comment Share on other sites More sharing options...
Polanskiman Posted November 14, 2016 Share #1217 Posted November 14, 2016 does anyone have a link to dsm 6.0 pat file?. looks like this is working... but i dont have a pat file. Google is your friend >>> https://usdl.synology.com/download/DSM/ ... s_8451.pat It's from Synology official servers. Quote Link to comment Share on other sites More sharing options...
Polanskiman Posted November 14, 2016 Share #1218 Posted November 14, 2016 Some Info for N54L users (AMD based)I burned the newest 1.01 Image on my USB Stick, adjusted PID, VID, SNR and MAC but still ran into "Booting the Kernel" without finding the NAS in my network. After i adjusted the timeout to '5' i had the chance to see the grub menu, where i could choose the AMD entry, which did the trick Thanks for the hard work I thought one second is enough Next update maybe change the timeout= parameter to default to 3 or 4 seconds. Should be plenty enough Quote Link to comment Share on other sites More sharing options...
lazygatto Posted November 14, 2016 Share #1219 Posted November 14, 2016 I've recently annouce that my work on a kernel mode dynamic patcher in this post .... How to install: find the vid/pid of your usb drive Burn the image to the drive, optionally edit grub.cfg to set vid/pid and boot entry, OR connect monitor/keyboard/serial console to your Box. Press C during Grub boot menu to enter command line vid 0xXXXX pid 0xYYYY to configure pid and vid ("pid" and "vid" are command, and "XXXX", "YYYY" are you usb drive's vid,pid) (There are a few other options can be config this way, you can read grub.cfg to know more detail.) Press Esc to go back to boot menu Select baremeta/baremetal AMD entry, press enter to boot. If your encounter the "disk port disabled" error during installation, try the force install menu entry. if both option does not work, you have to fallback to SataPortMap method, type this line in grub command line, replace XX with appropriate value. append SataPortMap=XX 11/2: as I promised, here is v1.01, download link is the same as v1.0 This update contains nothing fancy, mainly for inner peace, Plus, I revert megaraid_sas mpt3sas to old version. It's not shining new now, the title is obsolete My HP Microserver Gen8 can't boot by U-disk burned in your loader v1.01 as your indicate above. It shows "Non system disk" but works well with 5.2 XPEnoboot_DS3615xs_5.2-5644.5 from this forum. As I known, Gen8 can't boot by UEFI mode. Any suggestions? update: The U-disk above was unstable and my Gen8 was updated to DSM 6.0.2 with new U-sidk by your loader v1.01. Thanks! This DSM loader can boot in UEFI AND in legacy (BIOS) mode as well. Quote Link to comment Share on other sites More sharing options...
unmesh Posted November 14, 2016 Share #1220 Posted November 14, 2016 I'm trying to take the new DSM for a test drive in ESXi 6 with the new Jun 1.01 loader but importing the OVF file always gives me the error Failed to deploy VM: postNFCData failed Anyone else seeing this? I've tried the webui with both Chrome and Firefox in case there was a browser anomaly. I've also tried the Windows fat client but it too fails during upload. Quote Link to comment Share on other sites More sharing options...
unmesh Posted November 14, 2016 Share #1221 Posted November 14, 2016 Here is a working version for ESXi 6 (or 5.5) :https://mega.nz/#!7Y0zCQ6A!KyMADeLGTsnC ... Ds8rpGEvEY It's an OVF template with HW v10. Everything seems to work. RDM disk on LSI Virtual SAS SCSI controller are detected properly with power management, BTRFS and TV Tuner work. Jun, your version is HW v11 and for some reasons it ask for a reinstall in a loop so it does not work. Kind regards I built a VM with this OVF, installed DSM, installed Update 3 and was even able to reboot from the DSM UI. Once I powered down the VM, though, it cannot see the hard drives at power on and tries to PXE boot off the network and gives up saying it cannot find an OS. Any suggestions? Quote Link to comment Share on other sites More sharing options...
dgrigo Posted November 14, 2016 Share #1222 Posted November 14, 2016 Guys! the was "A new loader for latest DSM" is causing frustration, why the "was" like its not working anymore, even if its working with latest update and no 6.1 update is available yet. Best Quote Link to comment Share on other sites More sharing options...
Ponury_Typ Posted November 14, 2016 Share #1223 Posted November 14, 2016 Updated successfully 2 VMs on eSXI and Proxmox Could You post conf file of the VM on proxmox ? Quote Link to comment Share on other sites More sharing options...
Arcao Posted November 14, 2016 Share #1224 Posted November 14, 2016 Guys! the was "A new loader for latest DSM" is causing frustration, why the "was" like its not working anymore, even if its working with latest update and no 6.1 update is available yet. AFAIK, DSM 6.1 is a beta version which needs a new kernel image in bootloader, so not supported at the moment. Quote Link to comment Share on other sites More sharing options...
jun Posted November 14, 2016 Author Share #1225 Posted November 14, 2016 Some Info for N54L users (AMD based)I burned the newest 1.01 Image on my USB Stick, adjusted PID, VID, SNR and MAC but still ran into "Booting the Kernel" without finding the NAS in my network. After i adjusted the timeout to '5' i had the chance to see the grub menu, where i could choose the AMD entry, which did the trick Thanks for the hard work I thought one second is enough Next update maybe change the timeout= parameter to default to 3 or 4 seconds. Should be plenty enough Press up/down key before the menu is shown, the same way as you enter BIOS setup screen Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.