Trabalhador Anonimo Posted January 10 Share #1026 Posted January 10 Hi there. I´m trying to build a new test system on Virtualbox. I had tryied all models at m-shell, but I always get error on modules.alias.3.json.tgz checksun. Cloud you please verify if there is any mismatch? Best regards. 1 Quote Link to comment Share on other sites More sharing options...
sobig11 Posted January 22 Share #1027 Posted January 22 Hi .. i'am trying install my HP Microserver Gen 10 which ran before wirh DSM 6.1.3 with the redPill Loader... but i stuck at teh first step... i boot from the internal USB-Port as well as i did with DSM but first came error messages, that VGA and VESA Files could not be found, then the menu comes up in normal size...with just one entry if i try to build the loader the the script couldn't find the kernel file after "Loading Linux...." ERROR disk "hd0 ' msdos" not found .......... where can i change it or change the script to find it at the correct place... Thank you Quote Link to comment Share on other sites More sharing options...
ichel Posted February 1 Share #1028 Posted February 1 On 1/22/2024 at 5:44 PM, sobig11 said: Hi .. i'am trying install my HP Microserver Gen 10 which ran before wirh DSM 6.1.3 with the redPill Loader... but i stuck at teh first step... i boot from the internal USB-Port as well as i did with DSM but first came error messages, that VGA and VESA Files could not be found, then the menu comes up in normal size...with just one entry if i try to build the loader the the script couldn't find the kernel file after "Loading Linux...." ERROR disk "hd0 ' msdos" not found .......... where can i change it or change the script to find it at the correct place... Thank you same here Quote Link to comment Share on other sites More sharing options...
xpe48 Posted February 6 Share #1029 Posted February 6 Hi, trying this method, however I run into an issue after this loads to install DSM all of a sudden the screen goes blank and ping connectivity is lost to the hardware. Could this be related to i915 driver? --------------------------------------={ TinyCore RedPill Friend }=-------------------------------------- TCRP Friend Version : 0.1.0k 0.1.0 friend kernel version up from 5.15.26 to 6.4.16 0.1.0d Fix Some H/W Display Info, Add skip_vender_mac_interfaces cmdline to enable DSM's dhcp to use the correct mac and ip 0.1.0h Add process to abort boot if corrupted user_config.json is used 0.1.0j Remove skip_vender_mac_interfaces and panic cmdline (SAN MANAGER Cause of damage) 0.1.0k Added timestamp recording function before line in /mnt/tcrp/friendlog.log file. Model : SA6400, Serial : 2270TQRHSMTMY, Mac : D843AE17BF5B, Build : 7.2.0-64570, Update : 0, LKM : prod Loader BUS: usb CPU,MEM: 12th Gen Intel(R) Core(TM) i5-12500 [12 Thread(s)], 31.2G Memory DMI: Micro-Star International Co., Ltd. MS-7D40/MPG B760I EDGE WIFI (MS-7D40), BIOS A.60 01/10/2024 SAS/RAID HBAs Count : 0 , NICs Count : 1 System is running in UEFI boot mode Setting MAC Address from D8:43:AE:17:BF:5B to D8:43:AE:17:BF:5B on eth0 (r8169) IP Address :192.168.1.83, Network Interface Card : eth0 [10ec:8125] (r8125) Detecting upgrade : Ramdisk OK ! zImage OK ! Detecting Internet -> OK! Checking for latest friend -> OK, latest zImage : /mnt/tcrp/zImage-dsm initrd : /mnt/tcrp/initrd-dsm, Module Processing Method : EUDEV cmdline : withefi earlyprintk syno_hw_version=SA6400 console=ttyS0,115200n8 netif_num=1 pid=0xa836 earlycon=uart8250,io,0x3f8,115200n8 syno_port_thaw=1 SasIdxMap=0 mac1=D843AE17BF5B sn=2270TQRHSMTMY SMBusHddDynamicPower=0 vid=0x05dc elevator=elevator loglevel=15 HddHotplug=0 DiskIdxMap syno_hdd_detect=0 vender_format_version=2 sataboot2 syno_hdd_powerup_seq=0 log_buf_len=32M root=/dev/md0 SataPortMap syno_ttyS1=serial,0x2f8 syno_ttyS0=serial,0x3f8 Access http:/192.168.1.83:7681 via the TTYD web terminal to check the problem. (If you have any problems with the DSM installation steps, check the /var/log/linuxrc.syno.log file in this access) Default TTYD root password is blank User config is on /mnt/tcrp/user_config.json Press <r> to enter a menu for Reset DSM Password Press <e> to enter a menu for Edit USB/SATA Command Line Press <j> to enter a Junior mode (to re-install DSM) Press <ctrl-c> to stop boot booting in : 6 Press <ctrl-c> to stop boot booting in : 5 Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted February 11 Share #1030 Posted February 11 Ive been using TCRP friend also mshell etc only on intel. I assumed this all was intel only, all the way back to Junes loaders etc. Are people now using this TCRP with AMD? Like could i use a B550 AMD Board with a 5900x? Is so which DiskStation Model would i choose for this hardware? Quote Link to comment Share on other sites More sharing options...
Master Luke Posted March 23 Share #1031 Posted March 23 Dear Guys, I'm totally confused, but I hope, I can find help: System: Asus Q370M-C + Intel 9100, bare metal DS3622XS+ with 7.1.1-42962 The system ran over a half year. 50 days ago I had problems with booting. After little bit BIOS-Playing with UEFI and Legacy the 5th time the USB-Stick show me his boot-menu and I choose the right one. It starts and work until today. Today I must reboot my Xpenology-NAS and now, I can't boot anymore! BIOS reset etc. doesn't work (UEFI adjustment). I put the stick in another PC and after booting, the message was: error: symbol "grub_disk_native_sectors" not found Entering rescue mode... grub rescue> _ What can I do? Can I repair the stick or should I creat a new one? I want only my NAS back.... Thanks a lot! Best Regards! Quote Link to comment Share on other sites More sharing options...
Master Luke Posted March 23 Share #1032 Posted March 23 Guys, me again! Solution: I took an older stick (proofed by an older DSM 6.2 station) and made this on a separate Windows-PC (only booting in UEFI-Mode): https://github.com/PeterSuh-Q3/tinycore-redpill/blob/main/README.md I choose always the old system parameters! Means: DSM-Version, MAC, SN etc. But I did not changed/modified the VID and PID from the new USB-Stick. After preparation of the new loader, i put the stick in the NAS. The System/Stick installed itself and after few seconds: it works! I logged on the NAS with the known Syno-surface. I checked all my folders and links from other devices to the NAS! GREAT! Holy $hit! Thanks a lot to @Peter Suh !!! 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.