mymax Posted January 11, 2016 Share #526 Posted January 11, 2016 I found eject USB script on synology forum http://forum.synology.com/enu/viewtopic ... 39&t=35668 sync; /usr/syno/bin/synousbdisk -umount sdq; >/tmp/usbtab Where it can be placed ? For auto-start after full boot. p.s. right answer is: 1. create new script S99ZZZ_USB_eject.sh with sync; /usr/syno/bin/synousbdisk -umount sdk1; >/tmp/usbtab 2. copy it in the /usr/syno/etc/rc.d directory 3. give it the execute permission via ssh chmod +x S99ZZZ_USB_eject.sh 4. reboot I tried to run this script on N54L and it seems to work properly from the SSH shell, the volume is unmounted properly. But logging in into the admin webpage I get a warning that the USB disk has been removed improperly. Is there any problem? Link to comment Share on other sites More sharing options...
mymax Posted January 11, 2016 Share #527 Posted January 11, 2016 I found eject USB script on synology forum http://forum.synology.com/enu/viewtopic ... 39&t=35668 sync; /usr/syno/bin/synousbdisk -umount sdq; >/tmp/usbtab Where it can be placed ? For auto-start after full boot. p.s. right answer is: 1. create new script S99ZZZ_USB_eject.sh with sync; /usr/syno/bin/synousbdisk -umount sdk1; >/tmp/usbtab 2. copy it in the /usr/syno/etc/rc.d directory 3. give it the execute permission via ssh chmod +x S99ZZZ_USB_eject.sh 4. reboot I tried to run this script on N54L and it seems to work properly from the SSH shell, the volume is unmounted properly. But logging in into the admin webpage I get this warning: "External device USB Disk on Synology was not ejected properly." Is it correct? Link to comment Share on other sites More sharing options...
latonita Posted March 22, 2016 Share #528 Posted March 22, 2016 Is there a way to read temperature values from SMBus? I tried to install lm-sensors package, but it cant read since there is no i2c-piix4 kernel module (using 5.1) Link to comment Share on other sites More sharing options...
fakeman Posted April 1, 2016 Share #529 Posted April 1, 2016 Is eSATA port multiplier working on N40L with DSM 5.2? All already have 5 drives in the device, but running low on storage with them and need extra space. I plan to use an 4 oder 5 disk external drive enclosure. Any suggestions? I have N54L and tried (N40L/N54L only cpu difference), eSATA works, but if you are going to use multiple disk enclosure w/SATA multiplier then you will not get what you want. I have an Orico 3-bay eSATA enclosure, if I do not enable RAID mode then DSM will only recognize the 1st disk Link to comment Share on other sites More sharing options...
ordimans Posted August 5, 2016 Share #530 Posted August 5, 2016 What is the last version possible on N40L ? I have 5.0 4493 Link to comment Share on other sites More sharing options...
metys Posted August 6, 2016 Share #531 Posted August 6, 2016 I have DSM 5.2-5967 on N40L Link to comment Share on other sites More sharing options...
ordimans Posted August 7, 2016 Share #532 Posted August 7, 2016 OK. Can i use manual update with the good file to update ? Link to comment Share on other sites More sharing options...
grattamone Posted January 3, 2017 Share #533 Posted January 3, 2017 Hi, I just did an upgrade to 6.0.2-8451 update7 following Polanskiman's thread (viewtopic.php?f=2&t=22100) on my 2 HP N40L servers. Everything is ok on this platform, working great ! Link to comment Share on other sites More sharing options...
darkknigt Posted January 11, 2017 Share #534 Posted January 11, 2017 Thanks for the feedback. I was not sure whether to upgrade or not, but now that you've done it you've encouraged me. Any recommendation? Link to comment Share on other sites More sharing options...
oswaldini Posted January 12, 2017 Share #535 Posted January 12, 2017 Anyone get eSATA to work in DSM 6.0 ? Link to comment Share on other sites More sharing options...
grattamone Posted January 14, 2017 Share #536 Posted January 14, 2017 @darkknigt : no special recommandation but just to let you know, before I upgrade to version 6 my servers were already registered to Synology's Quickconnect service. So I had a valid MAC and S/N generated with the excel spreadsheet. Then when I upgraded to version 6, I just had to replace the PID and VID and everything went ok. @ oswaldini : i have 2 N40L with 6 HDDs inside with one HDD using eSATA. No issue detected. Everything's OK ! and I just did the "6.0.2-8451 update 8" update with no problem. Link to comment Share on other sites More sharing options...
oswaldini Posted January 14, 2017 Share #537 Posted January 14, 2017 How you set SataPortMap and BIOS ? I can't get eSATA to work :/ Link to comment Share on other sites More sharing options...
gazzaman2k Posted January 14, 2017 Share #538 Posted January 14, 2017 @darkknigt : no special recommandation but just to let you know, before I upgrade to version 6 my servers were already registered to Synology's Quickconnect service. So I had a valid MAC and S/N generated with the excel spreadsheet. Then when I upgraded to version 6, I just had to replace the PID and VID and everything went ok. @ oswaldini : i have 2 N40L with 6 HDDs inside with one HDD using eSATA. No issue detected. Everything's OK ! and I just did the "6.0.2-8451 update 8" update with no problem. does your quick connect work on v6? i have the N40L and juns loader but when i click the quick connect page it just gives me an error? Link to comment Share on other sites More sharing options...
hotshots Posted January 15, 2017 Share #539 Posted January 15, 2017 Quick connect has nothing to do with the version of the loader. You just must use the right combination of Mac and serial. This has been discussed many times... Link to comment Share on other sites More sharing options...
gazzaman2k Posted January 15, 2017 Share #540 Posted January 15, 2017 Quick connect has nothing to do with the version of the loader.You just must use the right combination of Mac and serial. This has been discussed many times... been there done that still gives me "the the system has failed to perform the requested operation, there is an unkown error" as soon as i click onto the "log in to or register a synology account" bit on the quick connect page within the DSM Link to comment Share on other sites More sharing options...
mightymartin Posted January 21, 2017 Share #541 Posted January 21, 2017 I have the same problem, but with AMD config. I do not know how to solve this. Link to comment Share on other sites More sharing options...
gazzaman2k Posted January 21, 2017 Share #542 Posted January 21, 2017 its not really needed anyway as i can remotely connect to the nas through port forwarding Link to comment Share on other sites More sharing options...
ordimans Posted March 12, 2017 Share #543 Posted March 12, 2017 Some have DSM 6.0 on 40L ? Or let run on 5.2 ? Because UPS are not detected by DSM ... Don't know if this can be use .... viewtopic.php?p=4292#p4292 Link to comment Share on other sites More sharing options...
littlestone Posted April 14, 2017 Share #544 Posted April 14, 2017 Wow. Anyone else has successful story? Hi, I just did an upgrade to 6.0.2-8451 update7 following Polanskiman's thread (viewtopic.php?f=2&t=22100) on my 2 HP N40L servers. Everything is ok on this platform, working great ! Link to comment Share on other sites More sharing options...
ordimans Posted April 16, 2017 Share #545 Posted April 16, 2017 Anyone here with 6.2 ? Link to comment Share on other sites More sharing options...
Gronaldo Posted June 17, 2017 Share #546 Posted June 17, 2017 On 2017-1-14 at 4:43 PM, oswaldini said: How you set SataPortMap and BIOS ? I can't get eSATA to work :/ Just remove completely. Link to comment Share on other sites More sharing options...
ordimans Posted June 27, 2017 Share #547 Posted June 27, 2017 I am working on my own kernel, to support AMD cpu. I compiled kernel with AMD support. But some difficulties to generate the boot image after with https://github.com/kref/scripts Link to comment Share on other sites More sharing options...
Polanskiman Posted June 28, 2017 Share #548 Posted June 28, 2017 17 hours ago, ordimans said: I am working on my own kernel, to support AMD cpu. I compiled kernel with AMD support. But some difficulties to generate the boot image after with https://github.com/kref/scripts Can't you just use Jun's boot image and replace the necessary files? Link to comment Share on other sites More sharing options...
ordimans Posted June 28, 2017 Share #549 Posted June 28, 2017 Good idea !! Just don't know if i must reuse the menuentry for AMD which was comment. It use bzImage and no zImage. ANd not sure if it's ok, because it seems to there is a crc checksum in a file... Link to comment Share on other sites More sharing options...
Polanskiman Posted June 28, 2017 Share #550 Posted June 28, 2017 4 minutes ago, ordimans said: Good idea !! Just don't know if i must reuse the menuentry for AMD which was comment. It use bzImage and no zImage. ANd not sure if it's ok, because it seems to there is a crc checksum in a file... Menu entry needs to be fixed. Probably the script too. Indeed, forgot about the checksum. Yes checksum need to be correct. Link to comment Share on other sites More sharing options...
Recommended Posts