mitch55 Posted April 13, 2022 Share #2476 Posted April 13, 2022 No, just one. How to modify this? I have to make manipulation again? Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 13, 2022 Author Share #2477 Posted April 13, 2022 11 minutes ago, mitch55 said: No, just one. How to modify this? I have to make manipulation again? No you can keep and test changing to DiskIdxMap=0C00 While at grub press e on your selection and edit your linux line until you find the right setting. Then you can mount the USB on TC and edit the grub.cfg manually for a permanent change 1 Quote Link to comment Share on other sites More sharing options...
mitch55 Posted April 13, 2022 Share #2478 Posted April 13, 2022 (edited) Heu... What do you mean by "mount the usb"? I found 😉 @djvas335, what is your configuration for SataPortMap and DiskIdxMap ? I don't find the correct parameters. It's ok, I found. Edited April 13, 2022 by mitch55 Quote Link to comment Share on other sites More sharing options...
cpresco Posted April 13, 2022 Share #2479 Posted April 13, 2022 21 hours ago, cpresco said: @anyone I'm considering migrating from DS918+ to DS3622xs+ for various reasons and recommendations I've seen in this thread. DSM is currently at 7.0.1-42218U3. TCRP is 0.4.5. Hardware is in my sig. Are these the correct steps for migrating an existing DS918+/7.0.1-42218U3 to DS3622xs+/7.0.1-42218U3? 1. Backup all data 2. Create a new USB loader with TCRP 0.4.6 from pocopico github 3. Remove existing USB loader and boot with new USB loader 4. Select Tiny Core Image Build during boot 5. Run following commands ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh clean now ./rploader.sh serialgen DS3622xs+ ./rploader.sh identifyusb now ./rploader.sh satamap now ./rploader.sh build broadwellnk-7.0.1-42218 I'm guessing that DSM will do it's own migration when I access DSM after the reboot. Once I have a successful migration to DS3622xs+/7.0.1-42218U3 I'll be considering the upgrade to DSM7.1 and am guessing that would be the two step update but I'm not sure what the sequence of events/commands would be for that. Anyone? Quote Link to comment Share on other sites More sharing options...
ColoradoMurf Posted April 13, 2022 Share #2480 Posted April 13, 2022 I'm hitting a wall for the last couple days and have tried and read everything possible and could really use some help please. Host: ESXi 7.0u3 VM: Sata Controller 0 - Attach TinyCore VMDK to this controller at 0:0 PCI Passthrough: - LSI9211-8i (Currently only have 4 disks attached out of 8 possible) I do everything to get the build (broadwellnk-7.1.0-42661) up and running. Once DSM starts, it is showing my drives as 2,3,4,5 instead of 1,2,3,4. SataPortMap: "1" DiskIdxMap: "0F" I have tried adding SasIdxMap: 0 and doesn't change anything. I have tried changing the DiskIdxMap and it doesn't change it either. Whatever number I put in the SataPortMap, then an equal number of starting drives are taken. Example, if I change it to 2, then Disk 1 and 2 are empty and my Disks start at 3. If I remove SataPortMap or put it = 0, then my DSM won't load. Goal: My Drives passed through on my LSI9211-8i to be disks 1-8 and the loader to be hidden. I know this is probably something simple but I am hitting my head against a wall trying to solve this for my OCD brain. Any help will be appreciated. Thanks in advance. Quote Link to comment Share on other sites More sharing options...
RedCat Posted April 13, 2022 Share #2481 Posted April 13, 2022 19 hours ago, RedCat said: I try to install under proxmox 920+ with 7.1.0. Loader is booting, find.synology.com find the 920+. I click connect, the next screen is: Dont detect hard drive in DS920+. 918 and 3622xs works for me under proxmox with 7.1 What is wrong? Does everyone else work and find hdds 920+ with 7.1? Quote Link to comment Share on other sites More sharing options...
nemesis122 Posted April 13, 2022 Share #2482 Posted April 13, 2022 Hi all do you know what this means ? i have created the Loader 7.1 3622 with all this command Fixing recursive fault .... see the last / i have 3 times rebootet thank you [DS3622xs+] ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh serialgen DS3622xs+ ./rploader.sh identifyusb now ./rploader.sh satamap now ./rploader.sh build broadwellnk-7.0.1-42218 ./rploader.sh clean now ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json ./rploader.sh build broadwellnk-7.1.0-42661 ./rploader.sh clean now; rm -rf /mnt/sdb3/auxfiles; rm -rf /home/tc/custom-module; ./rploader.sh backup now; [ 58.647045] Call Trace: [ 58.658944] [<ffffffff8106a2cc>] ? wq_worker_sleeping+0xc/0x90 [ 58.687819] [<ffffffff8155fc21>] __schedule+0x471/0x7c0 [ 58.713512] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 58.737657] [<ffffffff81053b40>] do_exit+0x680/0xa10 [ 58.762115] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 58.786005] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 58.811107] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 58.841627] [<ffffffff8155fa8d>] ? __schedule+0x2dd/0x7c0 [ 58.868207] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 58.896645] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 58.923800] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 58.950180] [<ffffffff81565612>] page_fault+0x22/0x30 [ 58.974934] [<ffffffff810b309b>] ? timecounter_read+0xb/0x50 [ 59.002384] [<ffffffffa019f8c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe] [ 59.036094] [<ffffffffa0177ff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe] [ 59.068123] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 59.095343] [<ffffffffa0177760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe] [ 59.128258] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 59.156742] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 59.183518] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 59.212042] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 59.235604] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 59.264827] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 59.290925] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 59.320369] Code: 89 de e8 0d a1 4f 00 49 8b 04 24 48 85 c0 75 e6 e9 07 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 8b 87 c8 04 00 00 <48> 8b 40 d8 c3 0f 1f 40 00 55 ba 08 00 00 00 48 89 e5 48 83 ec [ 59.411785] RIP [<ffffffff8106de27>] kthread_data+0x7/0x10 [ 59.438497] RSP <ffff8802f897fa90> [ 59.455290] CR2: ffffffffffffffd8 [ 59.471380] ---[ end trace 3b14681a2df59b1d ]--- [ 59.493565] Fixing recursive fault but reboot is needed! Quote Link to comment Share on other sites More sharing options...
sam juan Posted April 13, 2022 Share #2483 Posted April 13, 2022 7 hours ago, pocopico said: Can you both try recreating the loader ? ./rploader.sh ext platform-XXXXXXXXX add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json I've modified the script on redpill-misc extension for identifying missing HW to match the modules-load.d files. it should work for both. Tries to find CPU capabilities and NVIDIA GPU existence to disable the following: acpi-cpufreq on -> /lib/modules-load.d/70-cpufreq-kernel.conf crc32c-intel on -> /lib/modules-load.d/70-crypto-kernel.conf nvidia on -> /lib/modules-load.d/70-syno-nvidia-gpu.conf nvidia-uvm on -> /lib/modules-load.d/70-syno-nvidia-gpu.conf thanks @pocopico it works now (TSU) in my older CPU where it does not have SSE4.2 and speedstep. recreated the loader. Quote Link to comment Share on other sites More sharing options...
Unregistrado Posted April 13, 2022 Share #2484 Posted April 13, 2022 1 hour ago, ColoradoMurf said: I'm hitting a wall for the last couple days and have tried and read everything possible and could really use some help please. Host: ESXi 7.0u3 VM: Sata Controller 0 - Attach TinyCore VMDK to this controller at 0:0 PCI Passthrough: - LSI9211-8i (Currently only have 4 disks attached out of 8 possible) I do everything to get the build (broadwellnk-7.1.0-42661) up and running. Once DSM starts, it is showing my drives as 2,3,4,5 instead of 1,2,3,4. SataPortMap: "1" DiskIdxMap: "0F" I have tried adding SasIdxMap: 0 and doesn't change anything. I have tried changing the DiskIdxMap and it doesn't change it either. Whatever number I put in the SataPortMap, then an equal number of starting drives are taken. Example, if I change it to 2, then Disk 1 and 2 are empty and my Disks start at 3. If I remove SataPortMap or put it = 0, then my DSM won't load. Goal: My Drives passed through on my LSI9211-8i to be disks 1-8 and the loader to be hidden. I know this is probably something simple but I am hitting my head against a wall trying to solve this for my OCD brain. Any help will be appreciated. Thanks in advance. You need to remap the drives. When using a lsi card what I understood is it will always start one disk higher. Quote Link to comment Share on other sites More sharing options...
nemesis122 Posted April 13, 2022 Share #2485 Posted April 13, 2022 (edited) i have now again kernel panic with Tinycore Redpill newest version and buidling 7.1.... .3622 please help is the gen8 not compatible with 3622xs ?? thank you 95.848072] RIP [<ffffffff8106de27>] kthread_data+0x7/0x10 [ 95.875538] RSP <ffff8802f5effa90> [ 95.892268] CR2: ffffffffffffffd8 [ 95.908078] ---[ end trace 736d20c1730b6c0a ]--- [ 95.930136] Fixing recursive fault but reboot is needed! [ 186.527146] NMI watchdog: Watchdog detected hard LOCKUP on cpu 0dModules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc i40e(O) r8168(O) igb(O) i2c_algo_bit e1000e(O) vfat fat sha256_generic sg ixgbe(OE) vxlan(OE) dca(OE) ip6_udp_tunnel udp_tunnel usb_storage xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios] [ 186.527146] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P D OE 4.4.180+ #42661 [ 186.527147] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527147] task: ffffffff818114c0 ti: ffffffff81800000 task.ti: ffffffff81800000 [ 186.527148] RIP: 0010:[<ffffffff8108f18d>] [<ffffffff8108f18d>] queued_spin_lock_slowpath+0x13d/0x150 [ 186.527148] RSP: 0018:ffff880309603d48 EFLAGS: 00000002 [ 186.527149] RAX: 00000000000c0101 RBX: 0000000000000292 RCX: 0000000000000101 [ 186.527149] RDX: 0000000000000101 RSI: 0000000000000001 RDI: ffff880309696340 [ 186.527150] RBP: ffff880309603d48 R08: 0000000000000001 R09: 0000000000000004 [ 186.527150] R10: 000000000000024d R11: 00000000000001ee R12: 00000000000007ba [ 186.527151] R13: 000000000000024d R14: ffff8802fb4b8360 R15: ffff880309696340 [ 186.527151] FS: 0000000000000000(0000) GS:ffff880309600000(0000) knlGS:0000000000000000 [ 186.527151] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527152] CR2: 00007fdd61f429b8 CR3: 000000000180a000 CR4: 00000000001606f0 [ 186.527152] Stack: [ 186.527153] ffff880309603d60 ffffffff81563474 ffff8802fb48ec00 ffff880309603e58 [ 186.527153] ffffffff81084a47 ffff880309603e94 ffff88030960f230 0000000081076d54 [ 186.527153] ffff8802fb48f400 ffff8802fb48ec00 ffff8802fb48ec00 0000000000000000 [ 186.527154] Call Trace: [ 186.527154] <IRQ> d [<ffffffff81563474>] _raw_spin_lock_irqsave+0x24/0x30 [ 186.527155] [<ffffffff81084a47>] load_balance+0x277/0x940 [ 186.527155] [<ffffffff8108579e>] rebalance_domains+0x22e/0x2e0 [ 186.527155] [<ffffffff81085990>] run_rebalance_domains+0x140/0x1d0 [ 186.527156] [<ffffffff810552ba>] __do_softirq+0xca/0x2e0 [ 186.527156] [<ffffffff810aa21d>] ? hrtimer_interrupt+0xcd/0x180 [ 186.527157] [<ffffffff81055603>] irq_exit+0x93/0xa0 [ 186.527157] [<ffffffff81032643>] smp_apic_timer_interrupt+0x43/0x60 [ 186.527157] [<ffffffff8156459b>] apic_timer_interrupt+0x9b/0xa0 [ 186.527158] <EOI> d [<ffffffff8100d456>] ? mwait_idle+0xb6/0x190 [ 186.527158] [<ffffffff8100e020>] arch_cpu_idle+0x10/0x20 [ 186.527159] [<ffffffff8108abd8>] default_idle_call+0x28/0x30 [ 186.527159] [<ffffffff8108aef1>] cpu_startup_entry+0x311/0x320 [ 186.527160] [<ffffffff8155e50b>] rest_init+0x72/0x74 [ 186.527160] [<ffffffff818f5e55>] start_kernel+0x3e2/0x3ef [ 186.527160] [<ffffffff818f52e7>] x86_64_start_reservations+0x29/0x2b [ 186.527161] [<ffffffff818f53e2>] x86_64_start_kernel+0xf9/0x104 [ 186.527162] Code: 01 00 00 00 65 ff 0d 9f 7c f8 7e 5d c3 be 01 00 00 00 f0 0f b1 37 85 c0 0f 85 5a ff ff ff eb e4 83 fa 01 75 04 eb e4 f3 90 8b 07 <84> c0 75 f8 b8 01 00 00 00 5d 66 89 07 c3 0f 1f 44 00 00 48 c7 [ 186.527162] Sending NMI to other CPUs: [ 186.527162] NMI backtrace for cpu 1 [ 186.527163] CPU: 1 PID: 8044 Comm: hotplug Tainted: P D OE 4.4.180+ #42661 [ 186.527163] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527164] task: ffff8800f033f2c0 ti: ffff8802f5cb8000 task.ti: ffff8802f5cb8000 [ 186.527164] RIP: 0010:[<ffffffff8108f114>] [<ffffffff8108f114>] queued_spin_lock_slowpath+0xc4/0x150 [ 186.527165] RSP: 0018:ffff8802f5cbbe70 EFLAGS: 00000046 [ 186.527165] RAX: 0000000000000000 RBX: ffff8800361dd940 RCX: 0000000000080000 [ 186.527166] RDX: ffff880309656e00 RSI: 0000000000000003 RDI: ffff880309696340 [ 186.527166] RBP: ffff8802f5cbbe70 R08: 0000000000000001 R09: 0000000000000001 [ 186.527166] R10: 0000000000001cf2 R11: 0000000000000000 R12: ffff880309696340 [ 186.527167] R13: ffff8800361ddfac R14: ffffffff818d72a0 R15: 0000000000016340 [ 186.527167] FS: 00007fdabba30740(0000) GS:ffff880309640000(0000) knlGS:0000000000000000 [ 186.527168] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527168] CR2: 000000000043eb9a CR3: 00000002f8531000 CR4: 00000000001606f0 [ 186.527169] Stack: [ 186.527169] ffff8802f5cbbe80 ffffffff8156350c ffff8802f5cbbec0 ffffffff810789ee [ 186.527169] 0000000000000286 ffff8800f033f2c0 0000000000000000 ffff8800361dd940 [ 186.527170] 0000000000002051 0000000000000000 ffff8802f5cbbf38 ffffffff810504e8 [ 186.527170] Call Trace: [ 186.527171] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 186.527171] [<ffffffff810789ee>] wake_up_new_task+0xae/0x1b0 [ 186.527171] [<ffffffff810504e8>] _do_fork+0xf8/0x320 [ 186.527172] [<ffffffff81050794>] SyS_clone+0x14/0x20 [ 186.527172] [<ffffffff8156380a>] entry_SYSCALL_64_fastpath+0x1e/0x8e [ 186.527173] Code: 46 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 <8b> 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 [ 186.527173] NMI backtrace for cpu 2 [ 186.527174] CPU: 2 PID: 3924 Comm: kworker/u48:5 Tainted: P D OE 4.4.180+ #42661 [ 186.527174] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527175] task: ffff8802faba0000 ti: ffff8802f5efc000 task.ti: ffff8802f5efc000 [ 186.527175] RIP: 0010:[<ffffffff8108f114>] [<ffffffff8108f114>] queued_spin_lock_slowpath+0xc4/0x150 [ 186.527176] RSP: 0018:ffff8802f5eff7b0 EFLAGS: 00000046 [ 186.527176] RAX: 0000000000000000 RBX: 0000000000016340 RCX: 00000000000c0000 [ 186.527177] RDX: ffff880309696e00 RSI: 0000000000000001 RDI: ffff880309696340 [ 186.527177] RBP: ffff8802f5eff7b0 R08: 0000000000000001 R09: 00000000000008e2 [ 186.527178] R10: 0000000000000006 R11: ffffffff81a056ad R12: 0000000000000009 [ 186.527178] R13: ffff880309696340 R14: ffff880309696340 R15: 0000000000000002 [ 186.527178] FS: 0000000000000000(0000) GS:ffff880309680000(0000) knlGS:0000000000000000 [ 186.527179] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527179] CR2: 0000000000000028 CR3: 000000000180a000 CR4: 00000000001606f0 [ 186.527180] Stack: [ 186.527180] ffff8802f5eff7c0 ffffffff8156338d ffff8802f5eff810 ffffffff8155f83d [ 186.527181] 0000000081125b08 0000000000000008 ffff8802faba0000 ffff8802faba0000 [ 186.527181] 0000000000000009 0000000000000046 ffff8802faba0000 0000000000000009 [ 186.527181] Call Trace: [ 186.527182] [<ffffffff8156338d>] _raw_spin_lock_irq+0x1d/0x20 [ 186.527182] [<ffffffff8155f83d>] __schedule+0x8d/0x7c0 [ 186.527182] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 186.527183] [<ffffffff811219f3>] do_exit.cold.24+0x4f/0x74 [ 186.527183] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 186.527184] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 186.527184] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 186.527184] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 186.527185] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 186.527185] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 186.527186] [<ffffffff81565612>] page_fault+0x22/0x30 [ 186.527186] [<ffffffff8106de27>] ? kthread_data+0x7/0x10 [ 186.527186] [<ffffffff8106a2cc>] ? wq_worker_sleeping+0xc/0x90 [ 186.527187] [<ffffffff8155fc21>] __schedule+0x471/0x7c0 [ 186.527187] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 186.527188] [<ffffffff81053b40>] do_exit+0x680/0xa10 [ 186.527188] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 186.527188] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 186.527189] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 186.527189] [<ffffffff8155fa8d>] ? __schedule+0x2dd/0x7c0 [ 186.527190] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 186.527190] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 186.527190] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 186.527191] [<ffffffff81565612>] page_fault+0x22/0x30 [ 186.527191] [<ffffffff810b309b>] ? timecounter_read+0xb/0x50 [ 186.527192] [<ffffffffa019f8c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe] [ 186.527192] [<ffffffffa0177ff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe] [ 186.527193] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 186.527193] [<ffffffffa0177760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe] [ 186.527193] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 186.527194] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 186.527194] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 186.527195] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 186.527195] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527195] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 186.527196] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527197] Code: 46 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 <8b> 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 [ 186.527197] NMI backtrace for cpu 3 [ 186.527198] CPU: 3 PID: 6 Comm: kworker/u48:0 Tainted: P D OE 4.4.180+ #42661 [ 186.527198] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527198] Workqueue: events_unbound call_usermodehelper_exec_work [ 186.527199] task: ffff8802fb56bfc0 ti: ffff8802fb5a4000 task.ti: ffff8802fb5a4000 [ 186.527199] RIP: 0010:[<ffffffff8108f130>] [<ffffffff8108f130>] queued_spin_lock_slowpath+0xe0/0x150 [ 186.527200] RSP: 0018:ffff8802fb5a7d00 EFLAGS: 00000002 [ 186.527200] RAX: 00000000000c0101 RBX: ffff8802f69a8cc0 RCX: 0000000000100000 [ 186.527201] RDX: ffff8803096d6e00 RSI: 0000000000000000 RDI: ffff880309696340 [ 186.527201] RBP: ffff8802fb5a7d00 R08: 0000000000000001 R09: 0000000000000001 [ 186.527202] R10: ffff8802f8e89ce0 R11: 0000000000000000 R12: ffff880309696340 [ 186.527202] R13: ffff8802f69a932c R14: ffffffff818d72a0 R15: 0000000000016340 [ 186.527203] FS: 0000000000000000(0000) GS:ffff8803096c0000(0000) knlGS:0000000000000000 [ 186.527203] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527203] CR2: 0000000000a74298 CR3: 00000002f6146000 CR4: 00000000001606f0 [ 186.527204] Stack: [ 186.527204] ffff8802fb5a7d10 ffffffff8156350c ffff8802fb5a7d50 ffffffff810789ee [ 186.527205] 0000000000000282 ffff8802fb56bfc0 0000000000000000 ffff8802f69a8cc0 [ 186.527205] 0000000000002050 0000000000000000 ffff8802fb5a7dc8 ffffffff810504e8 [ 186.527205] Call Trace: [ 186.527206] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 186.527206] [<ffffffff810789ee>] wake_up_new_task+0xae/0x1b0 [ 186.527206] [<ffffffff810504e8>] _do_fork+0xf8/0x320 [ 186.527207] [<ffffffff81076d18>] ? check_preempt_curr+0x68/0x90 [ 186.527207] [<ffffffff81076d54>] ? ttwu_do_wakeup+0x14/0xf0 [ 186.527208] [<ffffffff81050734>] kernel_thread+0x24/0x30 [ 186.527208] [<ffffffff81064eea>] call_usermodehelper_exec_work+0x8a/0xa0 [ 186.527209] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 186.527209] [<ffffffff81064e60>] ? call_usermodehelper_exec_async+0x130/0x130 [ 186.527209] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 186.527210] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 186.527210] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 186.527211] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 186.527211] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527211] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 186.527212] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527213] Code: 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 8b 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 e9 32 ff ff ff f3 90 <8b> 07 66 85 c0 75 f7 39 c1 75 0f 89 c8 be 01 00 00 00 f0 0f b1 [ 186.527215] Kernel panic - not syncing: Hard LOCKUP [ 187.560268] Shutting down cpus with NMI [ 187.560269] Kernel Offset: disabled [ 192.602209] ---[ end Kernel panic - not syncing: Hard LOCKUP 622xs Edited April 13, 2022 by nemesis122 Quote Link to comment Share on other sites More sharing options...
djvas335 Posted April 13, 2022 Share #2486 Posted April 13, 2022 I have Microserver gen8 running on ds3622xs+ 7.1 with no issues, however my cpu is core i3, also there is one step less which I used to compile redpill for gen8 ie omit this step while building loader ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json 44 minutes ago, nemesis122 said: i have now again kernel panic with Tinycore Redpill newest version and buidling 7.1.... .3622 please help is the gen8 not compatible with 3622xs ?? thank you 95.848072] RIP [<ffffffff8106de27>] kthread_data+0x7/0x10 [ 95.875538] RSP <ffff8802f5effa90> [ 95.892268] CR2: ffffffffffffffd8 [ 95.908078] ---[ end trace 736d20c1730b6c0a ]--- [ 95.930136] Fixing recursive fault but reboot is needed! [ 186.527146] NMI watchdog: Watchdog detected hard LOCKUP on cpu 0dModules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc i40e(O) r8168(O) igb(O) i2c_algo_bit e1000e(O) vfat fat sha256_generic sg ixgbe(OE) vxlan(OE) dca(OE) ip6_udp_tunnel udp_tunnel usb_storage xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios] [ 186.527146] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P D OE 4.4.180+ #42661 [ 186.527147] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527147] task: ffffffff818114c0 ti: ffffffff81800000 task.ti: ffffffff81800000 [ 186.527148] RIP: 0010:[<ffffffff8108f18d>] [<ffffffff8108f18d>] queued_spin_lock_slowpath+0x13d/0x150 [ 186.527148] RSP: 0018:ffff880309603d48 EFLAGS: 00000002 [ 186.527149] RAX: 00000000000c0101 RBX: 0000000000000292 RCX: 0000000000000101 [ 186.527149] RDX: 0000000000000101 RSI: 0000000000000001 RDI: ffff880309696340 [ 186.527150] RBP: ffff880309603d48 R08: 0000000000000001 R09: 0000000000000004 [ 186.527150] R10: 000000000000024d R11: 00000000000001ee R12: 00000000000007ba [ 186.527151] R13: 000000000000024d R14: ffff8802fb4b8360 R15: ffff880309696340 [ 186.527151] FS: 0000000000000000(0000) GS:ffff880309600000(0000) knlGS:0000000000000000 [ 186.527151] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527152] CR2: 00007fdd61f429b8 CR3: 000000000180a000 CR4: 00000000001606f0 [ 186.527152] Stack: [ 186.527153] ffff880309603d60 ffffffff81563474 ffff8802fb48ec00 ffff880309603e58 [ 186.527153] ffffffff81084a47 ffff880309603e94 ffff88030960f230 0000000081076d54 [ 186.527153] ffff8802fb48f400 ffff8802fb48ec00 ffff8802fb48ec00 0000000000000000 [ 186.527154] Call Trace: [ 186.527154] <IRQ> d [<ffffffff81563474>] _raw_spin_lock_irqsave+0x24/0x30 [ 186.527155] [<ffffffff81084a47>] load_balance+0x277/0x940 [ 186.527155] [<ffffffff8108579e>] rebalance_domains+0x22e/0x2e0 [ 186.527155] [<ffffffff81085990>] run_rebalance_domains+0x140/0x1d0 [ 186.527156] [<ffffffff810552ba>] __do_softirq+0xca/0x2e0 [ 186.527156] [<ffffffff810aa21d>] ? hrtimer_interrupt+0xcd/0x180 [ 186.527157] [<ffffffff81055603>] irq_exit+0x93/0xa0 [ 186.527157] [<ffffffff81032643>] smp_apic_timer_interrupt+0x43/0x60 [ 186.527157] [<ffffffff8156459b>] apic_timer_interrupt+0x9b/0xa0 [ 186.527158] <EOI> d [<ffffffff8100d456>] ? mwait_idle+0xb6/0x190 [ 186.527158] [<ffffffff8100e020>] arch_cpu_idle+0x10/0x20 [ 186.527159] [<ffffffff8108abd8>] default_idle_call+0x28/0x30 [ 186.527159] [<ffffffff8108aef1>] cpu_startup_entry+0x311/0x320 [ 186.527160] [<ffffffff8155e50b>] rest_init+0x72/0x74 [ 186.527160] [<ffffffff818f5e55>] start_kernel+0x3e2/0x3ef [ 186.527160] [<ffffffff818f52e7>] x86_64_start_reservations+0x29/0x2b [ 186.527161] [<ffffffff818f53e2>] x86_64_start_kernel+0xf9/0x104 [ 186.527162] Code: 01 00 00 00 65 ff 0d 9f 7c f8 7e 5d c3 be 01 00 00 00 f0 0f b1 37 85 c0 0f 85 5a ff ff ff eb e4 83 fa 01 75 04 eb e4 f3 90 8b 07 <84> c0 75 f8 b8 01 00 00 00 5d 66 89 07 c3 0f 1f 44 00 00 48 c7 [ 186.527162] Sending NMI to other CPUs: [ 186.527162] NMI backtrace for cpu 1 [ 186.527163] CPU: 1 PID: 8044 Comm: hotplug Tainted: P D OE 4.4.180+ #42661 [ 186.527163] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527164] task: ffff8800f033f2c0 ti: ffff8802f5cb8000 task.ti: ffff8802f5cb8000 [ 186.527164] RIP: 0010:[<ffffffff8108f114>] [<ffffffff8108f114>] queued_spin_lock_slowpath+0xc4/0x150 [ 186.527165] RSP: 0018:ffff8802f5cbbe70 EFLAGS: 00000046 [ 186.527165] RAX: 0000000000000000 RBX: ffff8800361dd940 RCX: 0000000000080000 [ 186.527166] RDX: ffff880309656e00 RSI: 0000000000000003 RDI: ffff880309696340 [ 186.527166] RBP: ffff8802f5cbbe70 R08: 0000000000000001 R09: 0000000000000001 [ 186.527166] R10: 0000000000001cf2 R11: 0000000000000000 R12: ffff880309696340 [ 186.527167] R13: ffff8800361ddfac R14: ffffffff818d72a0 R15: 0000000000016340 [ 186.527167] FS: 00007fdabba30740(0000) GS:ffff880309640000(0000) knlGS:0000000000000000 [ 186.527168] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527168] CR2: 000000000043eb9a CR3: 00000002f8531000 CR4: 00000000001606f0 [ 186.527169] Stack: [ 186.527169] ffff8802f5cbbe80 ffffffff8156350c ffff8802f5cbbec0 ffffffff810789ee [ 186.527169] 0000000000000286 ffff8800f033f2c0 0000000000000000 ffff8800361dd940 [ 186.527170] 0000000000002051 0000000000000000 ffff8802f5cbbf38 ffffffff810504e8 [ 186.527170] Call Trace: [ 186.527171] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 186.527171] [<ffffffff810789ee>] wake_up_new_task+0xae/0x1b0 [ 186.527171] [<ffffffff810504e8>] _do_fork+0xf8/0x320 [ 186.527172] [<ffffffff81050794>] SyS_clone+0x14/0x20 [ 186.527172] [<ffffffff8156380a>] entry_SYSCALL_64_fastpath+0x1e/0x8e [ 186.527173] Code: 46 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 <8b> 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 [ 186.527173] NMI backtrace for cpu 2 [ 186.527174] CPU: 2 PID: 3924 Comm: kworker/u48:5 Tainted: P D OE 4.4.180+ #42661 [ 186.527174] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527175] task: ffff8802faba0000 ti: ffff8802f5efc000 task.ti: ffff8802f5efc000 [ 186.527175] RIP: 0010:[<ffffffff8108f114>] [<ffffffff8108f114>] queued_spin_lock_slowpath+0xc4/0x150 [ 186.527176] RSP: 0018:ffff8802f5eff7b0 EFLAGS: 00000046 [ 186.527176] RAX: 0000000000000000 RBX: 0000000000016340 RCX: 00000000000c0000 [ 186.527177] RDX: ffff880309696e00 RSI: 0000000000000001 RDI: ffff880309696340 [ 186.527177] RBP: ffff8802f5eff7b0 R08: 0000000000000001 R09: 00000000000008e2 [ 186.527178] R10: 0000000000000006 R11: ffffffff81a056ad R12: 0000000000000009 [ 186.527178] R13: ffff880309696340 R14: ffff880309696340 R15: 0000000000000002 [ 186.527178] FS: 0000000000000000(0000) GS:ffff880309680000(0000) knlGS:0000000000000000 [ 186.527179] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527179] CR2: 0000000000000028 CR3: 000000000180a000 CR4: 00000000001606f0 [ 186.527180] Stack: [ 186.527180] ffff8802f5eff7c0 ffffffff8156338d ffff8802f5eff810 ffffffff8155f83d [ 186.527181] 0000000081125b08 0000000000000008 ffff8802faba0000 ffff8802faba0000 [ 186.527181] 0000000000000009 0000000000000046 ffff8802faba0000 0000000000000009 [ 186.527181] Call Trace: [ 186.527182] [<ffffffff8156338d>] _raw_spin_lock_irq+0x1d/0x20 [ 186.527182] [<ffffffff8155f83d>] __schedule+0x8d/0x7c0 [ 186.527182] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 186.527183] [<ffffffff811219f3>] do_exit.cold.24+0x4f/0x74 [ 186.527183] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 186.527184] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 186.527184] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 186.527184] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 186.527185] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 186.527185] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 186.527186] [<ffffffff81565612>] page_fault+0x22/0x30 [ 186.527186] [<ffffffff8106de27>] ? kthread_data+0x7/0x10 [ 186.527186] [<ffffffff8106a2cc>] ? wq_worker_sleeping+0xc/0x90 [ 186.527187] [<ffffffff8155fc21>] __schedule+0x471/0x7c0 [ 186.527187] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 186.527188] [<ffffffff81053b40>] do_exit+0x680/0xa10 [ 186.527188] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 186.527188] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 186.527189] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 186.527189] [<ffffffff8155fa8d>] ? __schedule+0x2dd/0x7c0 [ 186.527190] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 186.527190] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 186.527190] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 186.527191] [<ffffffff81565612>] page_fault+0x22/0x30 [ 186.527191] [<ffffffff810b309b>] ? timecounter_read+0xb/0x50 [ 186.527192] [<ffffffffa019f8c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe] [ 186.527192] [<ffffffffa0177ff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe] [ 186.527193] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 186.527193] [<ffffffffa0177760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe] [ 186.527193] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 186.527194] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 186.527194] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 186.527195] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 186.527195] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527195] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 186.527196] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527197] Code: 46 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 <8b> 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 [ 186.527197] NMI backtrace for cpu 3 [ 186.527198] CPU: 3 PID: 6 Comm: kworker/u48:0 Tainted: P D OE 4.4.180+ #42661 [ 186.527198] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 186.527198] Workqueue: events_unbound call_usermodehelper_exec_work [ 186.527199] task: ffff8802fb56bfc0 ti: ffff8802fb5a4000 task.ti: ffff8802fb5a4000 [ 186.527199] RIP: 0010:[<ffffffff8108f130>] [<ffffffff8108f130>] queued_spin_lock_slowpath+0xe0/0x150 [ 186.527200] RSP: 0018:ffff8802fb5a7d00 EFLAGS: 00000002 [ 186.527200] RAX: 00000000000c0101 RBX: ffff8802f69a8cc0 RCX: 0000000000100000 [ 186.527201] RDX: ffff8803096d6e00 RSI: 0000000000000000 RDI: ffff880309696340 [ 186.527201] RBP: ffff8802fb5a7d00 R08: 0000000000000001 R09: 0000000000000001 [ 186.527202] R10: ffff8802f8e89ce0 R11: 0000000000000000 R12: ffff880309696340 [ 186.527202] R13: ffff8802f69a932c R14: ffffffff818d72a0 R15: 0000000000016340 [ 186.527203] FS: 0000000000000000(0000) GS:ffff8803096c0000(0000) knlGS:0000000000000000 [ 186.527203] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 186.527203] CR2: 0000000000a74298 CR3: 00000002f6146000 CR4: 00000000001606f0 [ 186.527204] Stack: [ 186.527204] ffff8802fb5a7d10 ffffffff8156350c ffff8802fb5a7d50 ffffffff810789ee [ 186.527205] 0000000000000282 ffff8802fb56bfc0 0000000000000000 ffff8802f69a8cc0 [ 186.527205] 0000000000002050 0000000000000000 ffff8802fb5a7dc8 ffffffff810504e8 [ 186.527205] Call Trace: [ 186.527206] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 186.527206] [<ffffffff810789ee>] wake_up_new_task+0xae/0x1b0 [ 186.527206] [<ffffffff810504e8>] _do_fork+0xf8/0x320 [ 186.527207] [<ffffffff81076d18>] ? check_preempt_curr+0x68/0x90 [ 186.527207] [<ffffffff81076d54>] ? ttwu_do_wakeup+0x14/0xf0 [ 186.527208] [<ffffffff81050734>] kernel_thread+0x24/0x30 [ 186.527208] [<ffffffff81064eea>] call_usermodehelper_exec_work+0x8a/0xa0 [ 186.527209] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 186.527209] [<ffffffff81064e60>] ? call_usermodehelper_exec_async+0x130/0x130 [ 186.527209] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 186.527210] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 186.527210] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 186.527211] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 186.527211] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527211] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 186.527212] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 186.527213] Code: 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 8b 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 e9 32 ff ff ff f3 90 <8b> 07 66 85 c0 75 f7 39 c1 75 0f 89 c8 be 01 00 00 00 f0 0f b1 [ 186.527215] Kernel panic - not syncing: Hard LOCKUP [ 187.560268] Shutting down cpus with NMI [ 187.560269] Kernel Offset: disabled [ 192.602209] ---[ end Kernel panic - not syncing: Hard LOCKUP 622xs Quote Link to comment Share on other sites More sharing options...
nemesis122 Posted April 13, 2022 Share #2487 Posted April 13, 2022 (edited) this are my steps but there are some questions should i update your etc and i press always yes and one message said your partiton is only 2.9 mb ... i have tried with 16 GB stick and 115 Gb bove are the same the image was i use is tinycore-redpill.v0.4.6.img Please note im doing a fresh install not a upgrade What im doing wrong ? ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh serialgen DS3622xs+ ./rploader.sh identifyusb now ./rploader.sh satamap now ./rploader.sh build broadwellnk-7.0.1-42218 ./rploader.sh clean now ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json ./rploader.sh build broadwellnk-7.1.0-42661 ./rploader.sh clean now; rm -rf /mnt/sdb3/auxfiles; rm -rf /home/tc/custom-module; ./rploader.sh backup now; Edited April 13, 2022 by nemesis122 Quote Link to comment Share on other sites More sharing options...
nemesis122 Posted April 13, 2022 Share #2488 Posted April 13, 2022 is this step nessesary for a fresh install 1 +2 see the list? ./rploader.sh update now 1) ./rploader.sh fullupgrade now ./rploader.sh serialgen DS3622xs+ ./rploader.sh identifyusb now ./rploader.sh satamap now 2)./rploader.sh build broadwellnk-7.0.1-42218 ./rploader.sh clean now ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json ./rploader.sh build broadwellnk-7.1.0-42661 ./rploader.sh clean now; rm -rf /mnt/sdb3/auxfiles; rm -rf /home/tc/custom-module; ./rploader.sh backup now; Quote Link to comment Share on other sites More sharing options...
MajkelP Posted April 13, 2022 Share #2489 Posted April 13, 2022 On 4/12/2022 at 11:40 AM, pocopico said: Please remember SataPortMap is actually there to limit the number of available disk ports per controller. Controllers are enumerated as listed in lsscsi -Hv in that order. If you want no limits for a controller leave this open. E.g. no SataPortMap. The DiskIdxMap has to do with the disk numbers and how the disks will be represented to the system. Its a two digit hex value per controller. If you set DiskIdxMap=00 the first controller port/disk will start at 00. If you set DiskIdxMap=0008 the first controller will start at 00 and the second controller will start at 08. Thank you for your explanation @pocopico, I would like ask additional question. If want change above settings in working system, do I need start over again creating new loader (and edit file user_config.json)? or is there possibility to change above on existing working loader? Thanks Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 13, 2022 Author Share #2490 Posted April 13, 2022 1 minute ago, MajkelP said: Thank you for your explanation @pocopico, I would like ask additional question. If want change above settings in working system, do I need start over again creating new loader (and edit file user_config.json)? or is there possibility to change above on existing working loader? Thanks You can change that from within DSM or withing TC by editing grub.cfg which is on the first partition of the loader 1 Quote Link to comment Share on other sites More sharing options...
djvas335 Posted April 13, 2022 Share #2491 Posted April 13, 2022 All steps are necessary for any install just to be safe, and yes you need to answer yes to any question asked, or there is no point in running the command yes ? 4 minutes ago, nemesis122 said: is this step nessesary for a fresh install 1 +2 see the list? ./rploader.sh update now 1) ./rploader.sh fullupgrade now ./rploader.sh serialgen DS3622xs+ ./rploader.sh identifyusb now ./rploader.sh satamap now 2)./rploader.sh build broadwellnk-7.0.1-42218 ./rploader.sh clean now ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json ./rploader.sh build broadwellnk-7.1.0-42661 ./rploader.sh clean now; rm -rf /mnt/sdb3/auxfiles; rm -rf /home/tc/custom-module; ./rploader.sh backup now; 1 Quote Link to comment Share on other sites More sharing options...
RedCat Posted April 13, 2022 Share #2492 Posted April 13, 2022 I added the acpi extension to loader: ./rploader.sh ext apollolake-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/master/redpill-acpid/rpext-index.json The build is successfull, it write acpi2 added to loader I start the dsm 7.1, it boot, but the power button dont work. If I press it, the dsm dont halt. I tired it before under 7.0.1, there it worked Quote Link to comment Share on other sites More sharing options...
carlozo Posted April 13, 2022 Share #2493 Posted April 13, 2022 just wonder if this ok i am getting failed to preserve ownership tc@box:~$ Found /home/tc/redpill-load/cache/ds3622xsp_42218.pat, copying to cache director y : /mnt/sda3/auxfiles -sh: Found: not found tc@box:~$ cp: failed to preserve ownership for '/mnt/sda3/auxfiles/ds3622xsp_42218.pat': O peration not permitted -sh: cp:: not found tc@box:~$ tc@box:~$ Quote Link to comment Share on other sites More sharing options...
nemesis122 Posted April 13, 2022 Share #2494 Posted April 13, 2022 (edited) [ 198.618378] Stack: [ 198.618379] ffff8802f6abfe80 ffffffff8156350c ffff8802f6abfec0 ffffffff810789ee [ 198.618379] 0000000000000286 ffff8802f8d49980 0000000000000000 ffff8802f2880000 [ 198.618380] 0000000000001ff7 0000000000000000 ffff8802f6abff38 ffffffff810504e8 [ 198.618380] Call Trace: [ 198.618380] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 198.618381] [<ffffffff810789ee>] wake_up_new_task+0xae/0x1b0 [ 198.618381] [<ffffffff810504e8>] _do_fork+0xf8/0x320 [ 198.618381] [<ffffffff81050794>] SyS_clone+0x14/0x20 [ 198.618382] [<ffffffff8156380a>] entry_SYSCALL_64_fastpath+0x1e/0x8e [ 198.618383] Code: 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 8b 42 08 <85> c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 e9 32 ff [ 198.618384] NMI watchdog: Watchdog detected hard LOCKUP on cpu 2dModules linked in: broadwellnk_synobios(PO) adt7475 nfsv3 nfs lockd grace sunrpc i40e(O) r8168(O) igb(O) i2c_algo_bit e1000e(O) vfat fat sg sha256_generic synorbd(O) synofsbd(O) ixgbe(OE) vxlan(OE) dca(OE) ip6_udp_tunnel udp_tunnel usb_storage xhci_pci xhci_hcd ehci_pci ehci_hcd usbcore usb_common mv14xx(O) redpill(OE) [last unloaded: broadwellnk_synobios] [ 198.618385] CPU: 2 PID: 6 Comm: kworker/u48:0 Tainted: P D OE 4.4.180+ #42661 [ 198.618385] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 198.618385] task: ffff8802fb56bfc0 ti: ffff8802fb5a4000 task.ti: ffff8802fb5a4000 [ 198.618386] RIP: 0010:[<ffffffff8108f114>] [<ffffffff8108f114>] queued_spin_lock_slowpath+0xc4/0x150 [ 198.618386] RSP: 0018:ffff8802fb5a77b0 EFLAGS: 00000046 [ 198.618387] RAX: 0000000000000000 RBX: 0000000000016340 RCX: 00000000000c0000 [ 198.618387] RDX: ffff880309696e00 RSI: 0000000000000001 RDI: ffff880309696340 [ 198.618388] RBP: ffff8802fb5a77b0 R08: 0000000000000001 R09: 0000000000000ab1 [ 198.618388] R10: 0000000000000006 R11: ffffffff81a056ad R12: 0000000000000009 [ 198.618389] R13: ffff880309696340 R14: ffff880309696340 R15: 0000000000000002 [ 198.618389] FS: 0000000000000000(0000) GS:ffff880309680000(0000) knlGS:0000000000000000 [ 198.618390] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 198.618390] CR2: 0000000000000028 CR3: 00000002f5186000 CR4: 00000000001606f0 [ 198.618390] Stack: [ 198.618391] ffff8802fb5a77c0 ffffffff8156338d ffff8802fb5a7810 ffffffff8155f83d [ 198.618391] 0000000081125b08 0000000000000008 ffff8802fb56bfc0 ffff8802fb56bfc0 [ 198.618392] 0000000000000009 0000000000000046 ffff8802fb56bfc0 0000000000000009 [ 198.618392] Call Trace: [ 198.618392] [<ffffffff8156338d>] _raw_spin_lock_irq+0x1d/0x20 [ 198.618393] [<ffffffff8155f83d>] __schedule+0x8d/0x7c0 [ 198.618393] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 198.618394] [<ffffffff811219f3>] do_exit.cold.24+0x4f/0x74 [ 198.618394] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 198.618394] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 198.618395] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 198.618395] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 198.618396] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 198.618396] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 198.618396] [<ffffffff81565612>] page_fault+0x22/0x30 [ 198.618397] [<ffffffff8106de27>] ? kthread_data+0x7/0x10 [ 198.618397] [<ffffffff8106a2cc>] ? wq_worker_sleeping+0xc/0x90 [ 198.618398] [<ffffffff8155fc21>] __schedule+0x471/0x7c0 [ 198.618398] [<ffffffff8155ff96>] schedule+0x26/0x70 [ 198.618398] [<ffffffff81053b40>] do_exit+0x680/0xa10 [ 198.618399] [<ffffffff81007b95>] oops_end+0x85/0xa0 [ 198.618399] [<ffffffff8103ef7c>] no_context+0x12c/0x1d0 [ 198.618400] [<ffffffff8103f141>] __bad_area_nosemaphore+0x121/0x180 [ 198.618400] [<ffffffff8155fa8d>] ? __schedule+0x2dd/0x7c0 [ 198.618400] [<ffffffff8103f1ae>] bad_area_nosemaphore+0xe/0x10 [ 198.618401] [<ffffffff8103f3fb>] __do_page_fault+0x8b/0x3d0 [ 198.618401] [<ffffffff8103f74c>] do_page_fault+0xc/0x10 [ 198.618402] [<ffffffff81565612>] page_fault+0x22/0x30 [ 198.618402] [<ffffffff810b309b>] ? timecounter_read+0xb/0x50 [ 198.618402] [<ffffffffa019f8c4>] ixgbe_ptp_overflow_check+0x44/0x70 [ixgbe] [ 198.618403] [<ffffffffa0177ff5>] ixgbe_service_task+0x895/0xfd0 [ixgbe] [ 198.618403] [<ffffffff8107130a>] worker_run_work+0x9a/0xe0 [ 198.618404] [<ffffffffa0177760>] ? ixgbe_update_stats+0xe10/0xe10 [ixgbe] [ 198.618404] [<ffffffff810692bb>] process_one_work+0x1db/0x4e0 [ 198.618405] [<ffffffff810695ed>] worker_thread+0x2d/0x4a0 [ 198.618405] [<ffffffff810695c0>] ? process_one_work+0x4e0/0x4e0 [ 198.618405] [<ffffffff8106d9a3>] kthread+0xd3/0xf0 [ 198.618406] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 198.618406] [<ffffffff81563baf>] ret_from_fork+0x3f/0x80 [ 198.618407] [<ffffffff8106d8d0>] ? kthread_worker_fn+0x160/0x160 [ 198.618407] Code: 46 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 04 48 63 f6 48 05 00 6e 01 00 48 03 04 f5 a0 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 <8b> 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 [ 198.618408] Sending NMI to other CPUs: [ 198.618408] NMI backtrace for cpu 3 [ 198.618409] CPU: 3 PID: 7948 Comm: ifconfig Tainted: P D OE 4.4.180+ #42661 [ 198.618409] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 04/04/2019 [ 198.618409] task: ffff8802f59c0cc0 ti: ffff8800ef5e0000 task.ti: ffff8800ef5e0000 [ 198.618410] RIP: 0010:[<ffffffff8108f130>] [<ffffffff8108f130>] queued_spin_lock_slowpath+0xe0/0x150 [ 198.618410] RSP: 0018:ffff8800ef5e3a18 EFLAGS: 00000002 [ 198.618411] RAX: 00000000000c0101 RBX: ffff8802fafb0000 RCX: 0000000000100000 [ 198.618411] RDX: ffff8803096d6e00 RSI: 0000000000000000 RDI: ffff880309696340 [ 198.618412] RBP: ffff8800ef5e3a18 R08: 0000000000000001 R09: 0000000000000002 [ 198.618412] R10: 0000000000000003 R11: 0000000000000003 R12: ffff8802fafb066c [ 198.618413] R13: ffff880309696340 R14: 0000000000000000 R15: 0000000000000246 [ 198.618413] FS: 00007f583236a740(0000) GS:ffff8803096c0000(0000) knlGS:0000000000000000 [ 198.618414] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 198.618414] CR2: 00007fa1597c02a0 CR3: 00000000f111c000 CR4: 00000000001606f0 [ 198.618414] Stack: [ 198.618415] ffff8800ef5e3a28 ffffffff8156350c ffff8800ef5e3a78 ffffffff81077933 [ 198.618415] ffff8800ef5e3a60 ffffffff8120034e ffffffff00000002 ffff8802f52b8400 [ 198.618416] 0000000000000000 ffff8802faa79098 ffff8802f52b8400 0000000000000000 [ 198.618416] Call Trace: [ 198.618416] [<ffffffff8156350c>] _raw_spin_lock+0x1c/0x20 [ 198.618417] [<ffffffff81077933>] try_to_wake_up+0x193/0x3e0 [ 198.618417] [<ffffffff8120034e>] ? kernfs_activate+0x7e/0xe0 [ 198.618418] [<ffffffff81077b90>] wake_up_process+0x10/0x20 [ 198.618418] [<ffffffff813a3518>] devtmpfs_create_node+0xd8/0x110 [ 198.618418] [<ffffffff8139a9ba>] device_add+0x59a/0x5d0 [ 198.618419] [<ffffffff81143c4c>] ? kfree_const+0x1c/0x20 [ 198.618419] [<ffffffff8139abd3>] device_create_groups_vargs+0xd3/0xf0 [ 198.618420] [<ffffffff8139ac4c>] device_create+0x3c/0x40 [ 198.618420] [<ffffffff81444e20>] ptp_clock_register+0x1e0/0x2c0 [ 198.618420] [<ffffffff812e7ce9>] ? snprintf+0x39/0x40 [ 198.618421] [<ffffffffa01a01fa>] ixgbe_ptp_init+0x13a/0x330 [ixgbe] [ 198.618421] [<ffffffffa0175d93>] ixgbe_open+0x2f3/0x320 [ixgbe] [ 198.618422] [<ffffffff8106e671>] ? raw_notifier_call_chain+0x11/0x20 [ 198.618422] [<ffffffff814bbfd1>] __dev_open+0xb1/0x120 [ 198.618422] [<ffffffff814bc27e>] __dev_change_flags+0x9e/0x150 [ 198.618423] [<ffffffff814bc352>] dev_change_flags+0x22/0x60 [ 198.618423] [<ffffffff8152690c>] devinet_ioctl+0x5ec/0x6e0 [ 198.618424] [<ffffffff81527c64>] inet_ioctl+0x74/0xb0 [ 198.618424] [<ffffffff8149be16>] sock_do_ioctl+0x26/0x50 [ 198.618424] [<ffffffff8149c349>] sock_ioctl+0x209/0x260 [ 198.618425] [<ffffffff8119bd9a>] do_vfs_ioctl+0x7ea/0xa80 [ 198.618425] [<ffffffff8119c0d1>] SyS_ioctl+0xa1/0xb0 [ 198.618426] [<ffffffff8156380a>] entry_SYSCALL_64_fastpath+0x1e/0x8e [ 198.618427] Code: 72 8d 81 48 89 10 8b 42 08 85 c0 75 1e f3 90 8b 42 08 85 c0 74 f7 eb 13 f3 90 8b 37 81 fe 00 01 00 00 74 f4 e9 32 ff ff ff f3 90 <8b> 07 66 85 c0 75 f7 39 c1 75 0f 89 c8 be 01 00 00 00 f0 0f b1 [ 198.618430] Kernel panic - not syncing: Hard LOCKUP [ 199.651217] Shutting down cpus with NMI [ 199.651217] Kernel Offset: disabled [ 204.744931] ---[ end Kernel panic - not syncing: Hard LOCKUP cant understand what im doing wrong 🤔 Edited April 13, 2022 by nemesis122 Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 13, 2022 Author Share #2495 Posted April 13, 2022 8 minutes ago, carlozo said: just wonder if this ok i am getting failed to preserve ownership tc@box:~$ Found /home/tc/redpill-load/cache/ds3622xsp_42218.pat, copying to cache director y : /mnt/sda3/auxfiles -sh: Found: not found tc@box:~$ cp: failed to preserve ownership for '/mnt/sda3/auxfiles/ds3622xsp_42218.pat': O peration not permitted -sh: cp:: not found tc@box:~$ tc@box:~$ It’s normal. Don’t worry about that Quote Link to comment Share on other sites More sharing options...
carlozo Posted April 13, 2022 Share #2496 Posted April 13, 2022 thanks man just wonder how to get a new modelist apollolake-6.2.4-25556 apollolake-7.0-41890 apollolake-7.0.1-42218 broadwell-7.0.1-42218 broadwellnk-7.0.1-42218 bromolow-6.2.4-25556 bromolow-7.0-41222 bromolow-7.0.1-42218 v1000-7.0.1-42218 can t se broadwell-7.1.0-42661 must use broadwellnk-7.0.1-42218 first or what sorry asking to much i did sudo su ./rploader.sh update now ./rploader.sh serialgen DS3622xs+ ./rploader.sh satamap broadwellnk-7.1.0-42661 ./rploader.sh backup now ./rploader.sh build broadwellnk-7.1.0-42661 auto Quote Link to comment Share on other sites More sharing options...
blacktux88 Posted April 13, 2022 Share #2497 Posted April 13, 2022 is there an option to add Adaptec Series 6 with JBOD support ? thanks Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 13, 2022 Author Share #2498 Posted April 13, 2022 16 minutes ago, carlozo said: thanks man just wonder how to get a new modelist apollolake-6.2.4-25556 apollolake-7.0-41890 apollolake-7.0.1-42218 broadwell-7.0.1-42218 broadwellnk-7.0.1-42218 bromolow-6.2.4-25556 bromolow-7.0-41222 bromolow-7.0.1-42218 v1000-7.0.1-42218 can t se broadwell-7.1.0-42661 must use broadwellnk-7.0.1-42218 first or what sorry asking to much i did sudo su ./rploader.sh update now ./rploader.sh serialgen DS3622xs+ ./rploader.sh satamap broadwellnk-7.1.0-42661 ./rploader.sh backup now ./rploader.sh build broadwellnk-7.1.0-42661 auto Perform a ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh clean now then you will get latest files for the rest of the platforms Quote Link to comment Share on other sites More sharing options...
carlozo Posted April 13, 2022 Share #2499 Posted April 13, 2022 shall i do like this ./rploader.sh update now ./rploader.sh fullupgrade now ./rploader.sh clean now ./rploader.sh serialgen DS3622xs+ ./rploader.sh satamap broadwellnk-7.1.0-42661 ./rploader.sh backup now ./rploader.sh build broadwellnk-7.1.0-42661 auto because i get this ( '>') /) TC (\ Core is distributed with ABSOLUTELY NO WARRANTY. (/-_--_-\) www.tinycorelinux.net tc@box:~$ sudo su root@box:/home/tc# ./rploader.sh update now Checking Internet Access -> OK Checking if a newer version exists on the repo -> There is a newer version of the script on the repo should we use that ? [yY/nN]y OK, updating, please re-run after updating Updating tinycore loader with latest updates Backing up files to /mnt/sda3//mydata.tgz Done. root@box:/home/tc# ./rploader.sh fullupgrade now Performing a full TCRP upgrade Warning some of your local files will be moved to /home/tc/old/xxxx.2022-Apr-13-21-10 Updating custom_config.json % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 149 100 149 0 0 631 0 --:--:-- --:--:-- --:--:-- 634 100 33840 100 33840 0 0 80380 0 --:--:-- --:--:-- --:--:-- 80380 Updating global_config.json % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 149 100 149 0 0 598 0 --:--:-- --:--:-- --:--:-- 598 100 5692 100 5692 0 0 13456 0 --:--:-- --:--:-- --:--:-- 5558k Updating modules.alias.3.json.gz mv: cannot stat 'modules.alias.3.json.gz': No such file or directory % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 154 100 154 0 0 626 0 --:--:-- --:--:-- --:--:-- 626 100 5591 100 5591 0 0 20257 0 --:--:-- --:--:-- --:--:-- 20257 Updating modules.alias.4.json.gz mv: cannot stat 'modules.alias.4.json.gz': No such file or directory % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 154 100 154 0 0 652 0 --:--:-- --:--:-- --:--:-- 652 100 89007 100 89007 0 0 319k 0 --:--:-- --:--:-- --:--:-- 319k Updating rpext-index.json % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 147 100 147 0 0 620 0 --:--:-- --:--:-- --:--:-- 620 100 192k 100 192k 0 0 311k 0 --:--:-- --:--:-- --:--:-- 1073k Updating user_config.json % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 147 100 147 0 0 650 0 --:--:-- --:--:-- --:--:-- 650 100 431 100 431 0 0 1036 0 --:--:-- --:--:-- --:--:-- 1036 Updating dtc mv: cannot stat 'dtc': No such file or directory % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 134 100 134 0 0 592 0 --:--:-- --:--:-- --:--:-- 592 100 146k 100 146k 0 0 258k 0 --:--:-- --:--:-- --:--:-- 1055k Updating rploader.sh % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 142 100 142 0 0 601 0 --:--:-- --:--:-- --:--:-- 601 100 75085 100 75085 0 0 278k 0 --:--:-- --:--:-- --:--:-- 278k Updating ds1621p.dts mv: cannot stat 'ds1621p.dts': No such file or directory % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 142 100 142 0 0 550 0 --:--:-- --:--:-- --:--:-- 550 100 3026 100 3026 0 0 6452 0 --:--:-- --:--:-- --:--:-- 369k Updating ds920p.dts mv: cannot stat 'ds920p.dts': No such file or directory % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 141 100 141 0 0 613 0 --:--:-- --:--:-- --:--:-- 613 100 2423 100 2423 0 0 4965 0 --:--:-- --:--:-- --:--:-- 4965 Please make sure you are using the latest 1GB img before using backup option Current /home/tc size is 2.4M , try to keep it less than 1GB as it might not fit into your image Should i update the sda with your current files [Yy/Nn] y Backing up home files to sda : Backing up files to /mnt/sda3//mydata.tgz Done. root@box:/home/tc# ./rploader.sh clean now Clearing local redpill files root@box:/home/tc# ./rploader.sh serialgen DS3622xs+ Serial Number for Model : 20C0SQRATV8CE Mac Address for Model DS3622xs+ : 00:11:32:95:45:C2 Should i update the user_config.json with these values ? [Yy/Nn] y root@box:/home/tc# ./rploader.sh satamap broadwellnk-7.1.0-42661 Machine is VIRTUAL Hypervisor=VMware Running on VMware, Possible working solution, SataPortMap=1 DiskIdxMap=00 root@box:/home/tc# ./rploader.sh backup now Please make sure you are using the latest 1GB img before using backup option Current /home/tc size is 2.4M , try to keep it less than 1GB as it might not fit into your image Should i update the sda with your current files [Yy/Nn] y Backing up home files to sda : Backing up files to /mnt/sda3//mydata.tgz Done. root@box:/home/tc# ./rploader.sh build broadwellnk-7.1.0-42661 auto Rploader Version : 0.7.0.1 Loader source : https://github.com/pocopico/redpill-load.git Loader Branch : develop Redpill module source : https://github.com/dogodefi/redpill-lkm.git : Redpill module branch : develop Extensions : redpill-misc Extensions URL : "https://github.com/pocopico/redpill-load/raw/master/redpill-misc/rpext-index.json" TOOLKIT_URL : https://sourceforge.net/projects/dsgpl/files/toolkit/DSM7.0/ds.broadwellnk-7.0.dev.txz/download TOOLKIT_SHA : 0d9edca67d9e7e14c2529bbb58341b623936124d5264f71f1e4acbacf3ea202d SYNOKERNEL_URL : https://sourceforge.net/projects/dsgpl/files/Synology NAS GPL Source/25426branch/broadwellnk-source/linux-4.4.x.txz/download SYNOKERNEL_SHA : d3e85eb80f16a83244fcae6016ab6783cd8ac55e3af2b4240455261396e1e1be COMPILE_METHOD : toolkit_dev TARGET_PLATFORM : broadwellnk TARGET_VERSION : 7.1.0 TARGET_REVISION : 42661 REDPILL_LKM_MAKE_TARGET : dev-v7 KERNEL_MAJOR : 4 MODULE_ALIAS_FILE : modules.alias.4.json SYNOMODEL : ds3622xsp_42661 MODEL : DS3622xs+ Checking Internet Access -> OK Checking if a newer version exists on the repo -> Version is current Cloning into 'redpill-lkm'... remote: Enumerating objects: 1219, done. remote: Counting objects: 100% (1219/1219), done. remote: Compressing objects: 100% (579/579), done. remote: Total 1219 (delta 850), reused 1000 (delta 633), pack-reused 0 Receiving objects: 100% (1219/1219), 479.21 KiB | 4.99 MiB/s, done. Resolving deltas: 100% (850/850), done. Cloning into 'redpill-load'... remote: Enumerating objects: 1702, done. remote: Counting objects: 100% (820/820), done. remote: Compressing objects: 100% (406/406), done. remote: Total 1702 (delta 561), reused 601 (delta 404), pack-reused 882 Receiving objects: 100% (1702/1702), 28.44 MiB | 23.79 MiB/s, done. Resolving deltas: 100% (830/830), done. No extra build option specified, using default <static> Using static compiled redpill extension Removing any old redpill.ko modules Looking for redpill for : ds3622xsp_42661 Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/releases/redpill-4.4.180plus-broadwellnk.tgz Extracting module Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/src/check-redpill.sh Got redpill-linux-v4.4.180+.ko Testing modules.alias.4.json -> File OK ------------------------------------------------------------------------------------------------ It looks that you will need the following modules : Found IDE Controller : pciid 8086d00007111 Required Extension : No matching extension Found VGA Controller : pciid 15add00000405 Required Extension : vmwgfx Searching for matching extension for vmwgfx Found SATA Controller : pciid 15add000007e0 Required Extension : No matching extension Found SATA Controller : pciid 15add000007e0 Required Extension : No matching extension [#] Checking runtime for required tools... [OK] [#] Adding new extension from https://raw.githubusercontent.com/pocopico/rp-ext/master/vmxnet3/rpext-index.json... [#] Downloading remote file https://raw.githubusercontent.com/pocopico/rp-ext/master/vmxnet3/rpext-index.json to /home/tc/redpill-load/custom/extensions/_new_ext_index.tmp_json ######################################################################## 100.0% [OK] [#] ========================================== pocopico.vmxnet3 ========================================== [#] Extension name: vmxnet3 [#] Description: Adds VMware vmxnet3 virtual NIC driver Support [#] To get help visit: <todo> [#] Extension preparer/packer: https://github.com/pocopico/rp-ext/tree/main/vmxnet3 [#] Software author: https://github.com/pocopico [#] Update URL: https://raw.githubusercontent.com/pocopico/rp-ext/master/vmxnet3/rpext-index.json [#] Platforms supported: ds1621p_42218 ds918p_41890 dva3221_42661 ds3617xs_42621 ds3617xs_42218 ds920p_42661 ds918p_42661 ds1621p_42661 ds918p_25556 dva3221_42218 ds3615xs_42661 ds3622xsp_42661 ds3622xsp_42218 dva3221_42621 ds3615xs_41222 ds918p_42621 ds3617xs_42661 ds3615xs_25556 ds920p_42621 ds918p_42218 ds1621p_42621 ds3615xs_42621 ds3615xs_42218 ds3622xsp_42621 [#] ======================================================================================= Found Ethernet Interface : pciid 15add000007b0 Required Extension : vmxnet3 Searching for matching extension for vmxnet3 Found matching extension : "https://raw.githubusercontent.com/pocopico/rp-ext/master/vmxnet3/rpext-index.json" ------------------------------------------------------------------------------------------------ Starting loader creation Checking user_config.json : Done Entering redpill-load directory Removing bundled exts directories Cache directory OK Found build request for revision greater than 42218 Getting required extraction tool ------------------------------------------------------------------ Checking tinycore cache folder Creating temp folder /tmp/synoesp % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 345M 100 345M 0 0 77.6M 0 0:00:04 0:00:04 --:--:-- 81.7M Entering synoesp extract rd.gz finish 42506 blocks Copying required files to local cache folder for future use Copying usr/lib/libcurl.so.4 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libcurl.so.4': No such file or directory Copying usr/lib/libmbedcrypto.so.5 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libmbedcrypto.so.5': No such file or directory Copying usr/lib/libmbedtls.so.13 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libmbedtls.so.13': No such file or directory Copying usr/lib/libmbedx509.so.1 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libmbedx509.so.1': No such file or directory Copying usr/lib/libmsgpackc.so.2 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libmsgpackc.so.2': No such file or directory Copying usr/lib/libsodium.so to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libsodium.so': No such file or directory Copying usr/lib/libsynocodesign-ng-virtual-junior-wins.so.7 to /mnt/sda3/auxfiles cp: cannot stat 'usr/lib/libsynocodesign-ng-virtual-junior-wins.so.7': No such file or directory Copying usr/syno/bin/scemd to /mnt/sda3/auxfiles cp: cannot stat 'usr/syno/bin/scemd': No such file or directory Copying required libraries to local lib directory cp: cannot stat '/mnt/sda3/auxfiles/extractor/lib*': No such file or directory Linking lib to lib64 Copying executable cp: cannot stat '/mnt/sda3/auxfiles/extractor/scemd': No such file or directory Removing temp folder /tmp/synoesp Checking if tools is accessible ./rploader.sh: line 103: /bin/syno_extract_system_patch: No such file or directory Cound not execute Creating temp folder /tmp/pat Checking for cached pat file Found tinycore cache folder, linking to home/tc/custom-module Could not find pat file locally cached Configdir : /home/tc/redpill-load/config/DS3622xs+/7.1.0-42661 Configfile: /home/tc/redpill-load/config/DS3622xs+/7.1.0-42661/config.json Pat URL : https://global.download.synology.com/download/DSM/release/7.1/42661/DSM_DS3622xs%2B_42661.pat Downloading pat file from URL : https://global.download.synology.com/download/DSM/release/7.1/42661/DSM_DS3622xs%2B_42661.pat % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 348M 100 348M 0 0 60.5M 0 0:00:05 0:00:05 --:--:-- 60.8M File //mnt/sda3/auxfiles/ds3622xsp_42661.pat, is encrypted File //mnt/sda3/auxfiles/ds3622xsp_42661.pat, has been cached but its encrypted, re-running decrypting process Checking for cached pat file Found tinycore cache folder, linking to home/tc/custom-module Found locally cached pat file /home/tc/custom-module/ds3622xsp_42661.pat File /home/tc/custom-module/ds3622xsp_42661.pat, is encrypted Extracting encrypted pat file : /home/tc/custom-module/ds3622xsp_42661.pat to /tmp/pat sudo: /bin/syno_extract_system_patch: command not found extract latest pat Creating unecrypted pat file ds3622xsp_42661.pat to /home/tc/redpill-load/cache folder tar: ./VERSION: Not found in archive tar: Exiting with failure status due to previous errors Pat file sha256sum is : 427265d4e451b11e2f33ab5eac960da60ff2454f23363b86885419730cb00df1 Checking config file existence -> No config file found, please use the proper repo, clean and download again root@box:/home/tc# ./rploader.sh rploader.sh Version : 0.7.0.1 ---------------------------------------------------------------------------------------- Usage: ./rploader.sh <action> <platform version> <static or compile module> [extension manager arguments] Actions: build, ext, download, clean, update, listmod, serialgen, identifyusb, satamap, mountshare - build: Build the 💊 RedPill LKM and update the loader image for the specified platform version and update current loader. - ext: Manage extensions, options go after platform (add/force_add/info/remove/update/cleanup/auto) example: rploader.sh ext apollolake-7.0.1-42218 add https://raw.githubusercontent.com/pocopico/rp-ext/master/e1000/rpext-index.json or for auto detect use rploader.sh ext apollolake-7.0.1-42218 auto - download: Download redpill sources only - clean: Removes all cached files and starts over - update: Checks github repo for latest version of rploader - listmods: Tries to figure out required extensions - serialgen: Generates a serial number and mac address for the following platforms DS3615xs DS3617xs DS916+ DS918+ DS920+ DS3622xs+ FS6400 DVA3219 DVA3221 DS1621+ - identifyusb: Tries to identify your loader usb stick VID:PID and updates the user_config.json file - patchdtc: Tries to identify and patch your dtc model for your disk and nvme devices. - satamap: Tries to identify your SataPortMap and DiskIdxMap values and updates the user_config.json file - backup: Backup and make changes /home/tc changed permanent to your loader disk - backuploader: Backup current loader partitions to your TCRP partition - restoreloader:Restore current loader partitions from your TCRP partition - mountdsmroot: Mount DSM root for manual intervention on DSM root partition - postupdate: Runs a postupdate process to recreate your rd.gz, zImage and custom.gz for junior to match root - mountshare: Mounts a remote CIFS working directory Version : 0.7.0.1 ---------------------------------------------------------------------------------------- Available platform versions: ---------------------------------------------------------------------------------------- apollolake-6.2.4-25556 apollolake-7.0-41890 apollolake-7.0.1-42218 apollolake-7.1.0-42621 apollolake-7.1.0-42661 broadwell-7.0.1-42218 broadwell-7.1.0-42621 broadwell-7.1.0-42661 broadwellnk-7.0.1-42218 broadwellnk-7.1.0-42621 broadwellnk-7.1.0-42661 bromolow-6.2.4-25556 bromolow-7.0-41222 bromolow-7.0.1-42218 bromolow-7.1.0-42621 bromolow-7.1.0-42661 denverton-7.0.1-42218 denverton-7.1.0-42621 denverton-7.1.0-42661 geminilake-7.0.1-42218 geminilake-7.1.0-42621 geminilake-7.1.0-42661 v1000-7.0.1-42218 v1000-7.1.0-42621 v1000-7.1.0-42661 ---------------------------------------------------------------------------------------- Check global_settings.json for settings. root@box:/home/tc# hope i don t take your time is this right can you help please Quote Link to comment Share on other sites More sharing options...
pocopico Posted April 13, 2022 Author Share #2500 Posted April 13, 2022 50 minutes ago, carlozo said: thanks man just wonder how to get a new modelist apollolake-6.2.4-25556 apollolake-7.0-41890 apollolake-7.0.1-42218 broadwell-7.0.1-42218 broadwellnk-7.0.1-42218 bromolow-6.2.4-25556 bromolow-7.0-41222 bromolow-7.0.1-42218 v1000-7.0.1-42218 can t se broadwell-7.1.0-42661 must use broadwellnk-7.0.1-42218 first or what sorry asking to much i did sudo su ./rploader.sh update now ./rploader.sh serialgen DS3622xs+ ./rploader.sh satamap broadwellnk-7.1.0-42661 ./rploader.sh backup now ./rploader.sh build broadwellnk-7.1.0-42661 auto can you rerun only the last build part ? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.