pocopico Posted June 16, 2022 Author Share #3876 Posted June 16, 2022 1 hour ago, scfrancis said: Hello everyone, anyone to help me? @pocopico ?? 😊 I thin you need to contact @jumkey as he is the maintaner of this extension. Quote Link to comment Share on other sites More sharing options...
scfrancis Posted June 16, 2022 Share #3877 Posted June 16, 2022 à l’instant, pocopico a dit : I thin you need to contact @jumkey as he is the maintaner of this extension. OK thank you very much, @pocopico i will contact him now Quote Link to comment Share on other sites More sharing options...
Bose321 Posted June 17, 2022 Share #3878 Posted June 17, 2022 On 5/12/2022 at 1:49 PM, pocopico said: Change both to ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/develop/redpill-virtio/rpext-index.json ./rploader.sh ext broadwellnk-7.1.0-42661 add https://github.com/pocopico/redpill-load/raw/develop/redpill-acpid/rpext-index.json I've added these to my Unraid setup, and everything works great, except for the shutdown/reboot commands etc. They're not doing anything I'm afraid. Any idea what's missing here? Quote Link to comment Share on other sites More sharing options...
dodo-dk Posted June 17, 2022 Share #3879 Posted June 17, 2022 @Bose321 test this one https://raw.githubusercontent.com/dodo-dk/rp-ext/main/acpid/rpext-index.json 1 Quote Link to comment Share on other sites More sharing options...
testcb00 Posted June 18, 2022 Share #3880 Posted June 18, 2022 Hi, I want to try DSM using ASRock Q1900B-ITX but I find some issues. When I boot into Tinycore-Redpill, it shows nohup: redirecting stderr to stdout It seems that startx is failed. Luckily, I can access via PuTTY. Then, I use the scripts to edit the config and find that there are no SATA driver for 00:13.0 Intel Corporation Atom Processor E3800 Series SATA AHCI Controller (rev 0c) How to solve the problem? Quote Link to comment Share on other sites More sharing options...
testcb00 Posted June 18, 2022 Share #3881 Posted June 18, 2022 I solved the Bad Ports problem by Disable CSM and Enable Hot Plug. However, I cannot install DSM, the machine is in "Recover" loop. I have tried different models but no luck. Quote Link to comment Share on other sites More sharing options...
docop1 Posted June 18, 2022 Share #3882 Posted June 18, 2022 Quite a lot have change in 3 week. On the 14 may i can install redpill in esxi with Pcie LSI card. At the: sudo ./rploader.sh satamap now it was asking how many ports should be mapped, on the vmware Sata ctrl. with 1 drive connected (detected) Then it continue directly the second question: how many ports should be mapped for this controller. : As being the LSI ctrl. Now as on the 17jun and 18, the instal command don't ask this anymore for the LSI. By chance i screengrab the setting. As the only way is to enter this manually. to put : SataPortMap=148 DiskIdxMap=100004. With the Lsi card, it cannot get a proper dhcp ip when the dsm first boot. Never found in the synoAssistant. But when install with only sata 0 : redpill , sata 1:0 a new hdd and nothing else. it can install. Then i try to edit file in /proc/cmdline to mod the sataportmap and Disklxdxmap. And at boot i punch 'e' and also add there. And the lsi is show. Don't know if it survive multiple reboot or a cold shutdown. Also, for the update, by doing it give lot of error: sudo ./rploader.sh update sudo ./rploader.sh postupdate broadwellnk-7.1.0-42661 i got that : remote: Total 1253 (delta 302), reused 284 (delta 283), pack-reused 928 Receiving objects: 100% (1253/1253), 469.84 KiB | 692.00 KiB/s, done. Resolving deltas: 100% (865/865), done. Cloning into 'redpill-load'... remote: Enumerating objects: 2028, done. error: RPC failed; curl 56 OpenSSL SSL_read: Connection timed out error: 6376 bytes of body are still expected fetch-pack: unexpected disconnect while reading sideband packet fatal: early EOF fatal: fetch-pack: invalid index-pack output Removing any old redpill.ko modules Looking for redpill for : ds3622xsp_42661 Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/releases/redpill-4.4.180plus-broadwellnk.tgz Extracting module Getting file https://raw.githubusercontent.com/pocopico/rp-ext/master/redpill/src/check-redpill.sh mv: cannot move '/home/tc/redpill.ko' to '/home/tc/redpill-load/ext/rp-lkm/redpill-linux-v4.4.180+.ko': No such file or directory Creating temp ramdisk space Mounting partition sda1} Mounting partition sda2} Extracting update ramdisk unlzma: /mnt/sda2/rd.gz: Compressed data is corrupt 52176 blocks Found Version : 7.1-42661-2 Do you want to use this for the loader ? [yY/nN] : y Extracting redpill ramdisk And in the folder i don't have the file listed here as : exitcheck.sh i simply reboot to normal mode and in dsm it show 7.1u2. Is the ext driver install with 7.1u1 are still present, or the cleanup made in the first place to remove all ? Quote Link to comment Share on other sites More sharing options...
flyride Posted June 19, 2022 Share #3883 Posted June 19, 2022 FWIW, satamp does not ask about LSI controller ports as it is not a AHCI SATA controller. LSI ignores SataPortMap and DiskIdxMap - those only apply to AHCI SATA. It just tacks on its ports at the end of whatever SATA ports are defined. Quote Link to comment Share on other sites More sharing options...
docop1 Posted June 19, 2022 Share #3884 Posted June 19, 2022 here is Lsi port, detected and ask to be add in the configuration. That was working fine. Current version don't detect Lsi2008 card anymore and if add at the deploy, no dhcp get detected. Quote Link to comment Share on other sites More sharing options...
noxios Posted June 19, 2022 Share #3885 Posted June 19, 2022 (edited) Dear friends I have an HP Microserver Gen8, and after some info and questions here on the forum, I finally manage to install (through redpill) the various possible versions of NAS, I chose the 3622xs+, and the system is well installed and fluid, but apparently on this hardware, and this version, not all the sata ports are recognizable, with the exception of one + one sdd (placed in the fifth possible sata port dedicated to an ex cd player) Could you guide me and or tell me how on this device I can have access to all SATA ports and consequently to all disks? 3 in total + SSD I previously had xpenology version 6.2.4 (3617xs) and everything worked perfectly but in this new version of 7.1.0 (3622xs) it doesn't detect all disks automatically, maybe some adjustments can reverse/fix this situation but I'm not aware of how or what commands to use to achieve this end, can anybody help me ? Thank you Edited June 19, 2022 by noxios Quote Link to comment Share on other sites More sharing options...
docop1 Posted June 19, 2022 Share #3886 Posted June 19, 2022 @noxiosIt's a matter of extension. i have seen few post about that on gen8 and were working fine. look over github or dig among the thread (156page currently). 2 months ago i had a gen8 and all were detected when i install just to test out. But you better to put an lsi card as the hdd3-4 are not sata3. Quote Link to comment Share on other sites More sharing options...
neonflx Posted June 19, 2022 Share #3887 Posted June 19, 2022 I was able to install on bare metal a few months ago, since I tried to use TCRP to get 7.1 on clean install, can't find disks with the latest , same for esxi not sure what's going on with satamap , not complaining at all, just want to share my experience Quote Link to comment Share on other sites More sharing options...
wimsan Posted June 20, 2022 Share #3888 Posted June 20, 2022 Hi all, I successfully installed a DS1621+ in Proxmox. This is with a e1000 network interface. With the e1000 interface I get a network status (1 Gbps full Duplex) If I change the network interface to virtio I do not get a network status in DSM. I would like to go to virtio because it is faster than e1000 but I do need a network status to be able to build a High Availablity pair. I built the 1621 using myv.sh and added several network drivers like e1000, rtl8169 (because my mobo has a realtek LAN interface),v9fs. Is there another virtio driver available for DS1621+ that does give a network status in Proxmox? If so where can I find it? Quote Link to comment Share on other sites More sharing options...
irishj Posted June 20, 2022 Share #3889 Posted June 20, 2022 (edited) 18 hours ago, neonflx said: I was able to install on bare metal a few months ago, since I tried to use TCRP to get 7.1 on clean install, can't find disks with the latest , same for esxi not sure what's going on with satamap , not complaining at all, just want to share my experience I've you're referring to getting the 3622XS working and finding the disks attached to a HBA, I had a similar issue recently and after hours of troubleshooting, I ended up installing with 3617XS and it worked on the first attempt. I had two primary issues with the 3622XS. 1. The network adapter I was using, an Intel X540 was detected in TCRP and assigned IP addresses. Once I booted the loader it couldn't be detected in the network using Synology assistant. I changed to a Intel X710, which uses a different driver and it worked on the first attempt. 2 The eight harddisks I have attached to a HBA would be detected when I ran the satamap command, but when booting the loader and installer, it would say no disks available. I changed to 3617XS and all eight disks were detected on the first attempt at installing. There are issues with using 3266XS, so I'd instead recommend trying one of the other models like the 3617XS. Edited June 20, 2022 by irishj Quote Link to comment Share on other sites More sharing options...
noxios Posted June 20, 2022 Share #3890 Posted June 20, 2022 (edited) On 6/19/2022 at 5:05 PM, docop1 said: @noxiosIt's a matter of extension. i have seen few post about that on gen8 and were working fine. look over github or dig among the thread (156page currently). 2 months ago i had a gen8 and all were detected when i install just to test out. But you better to put an lsi card as the hdd3-4 are not sata3. Thank you @docop1 Finally I managed to understand how to put xpenology 7.1 (and others) in the various variants possible to emulate on the NAS, HP Proliant Microserver Gen8. It's actually very simple once you understand... of course 😉 (I chose to install the DS3622xs distro because I already used the DS3617xs with the previous "Jo Loader", and the new version 7.1 with redpill, works like a charm and detects all disks after some adjustments in the BIOS of my NAS HP). Very important! there is a relationship between the device's bios and the redpill loader. In any case, thank you very much, and 👍 for the developers of the very complete and functional redpill loader (I ended up for testing the version "tinycore-redpill.v0.9.0.2" and i think is even better !) Best regards Edited June 20, 2022 by noxios Quote Link to comment Share on other sites More sharing options...
sliders Posted June 20, 2022 Share #3891 Posted June 20, 2022 hi , testing the version "tinycore-redpill.v0.9.0.2" ????? the last version tinycore-redpill.v0.8.0.0 no ???? Quote Link to comment Share on other sites More sharing options...
flyride Posted June 21, 2022 Share #3892 Posted June 21, 2022 0.8.0 is the TCRP "stable release" 0.9.0 is the TCRP development release Use the stable release unless you are testing something for development. Quote Link to comment Share on other sites More sharing options...
shibby Posted June 21, 2022 Share #3893 Posted June 21, 2022 My experience of TCRP by @pocopico... from half year or better I had my own compilation of redpill loader for 918+ 7.0.1 Update 2. All works fine, all 6 drives detected (SHR2 from 4 drives and SHR from 2 drives)), ssd cache works, HW acceletarion works, atlantic 10GbE card works - happy me. Until i upgraded to "7.01. upgrade 4" and brick my xpenology (migratable loop). Then i burn TCRP 0.8.0.0 and build: 1) DS918+ Jun - Synology Assistant detected my NAS as "not installed" !! want to do fresh instalation 2) DS920+ Jun - Synology Assistant didnt find my NAS 3) DS920+ Jun with @Peter Suh my.sh script and @jumkey repo - Synology Assistant found my NAS as migratable. I did migration, NAS started but only 4 drives has been detected (and 2 NVMe for cache). Sata 5 and 6 (second raid array) has not been detected. 4) DS3622xsp Jun - found and migrated, working at the moment but... i cannot add extension for mu 10GbE card because of sum control error. I need HW acceleration... Benefits? I have latest DSM firmware... Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted June 21, 2022 Share #3894 Posted June 21, 2022 3 hours ago, shibby said: My experience of TCRP by @pocopico... from half year or better I had my own compilation of redpill loader for 918+ 7.0.1 Update 2. All works fine, all 6 drives detected (SHR2 from 4 drives and SHR from 2 drives)), ssd cache works, HW acceletarion works, atlantic 10GbE card works - happy me. Until i upgraded to "7.01. upgrade 4" and brick my xpenology (migratable loop). Then i burn TCRP 0.8.0.0 and build: 1) DS918+ Jun - Synology Assistant detected my NAS as "not installed" !! want to do fresh instalation 2) DS920+ Jun - Synology Assistant didnt find my NAS 3) DS920+ Jun with @Peter Suh my.sh script and @jumkey repo - Synology Assistant found my NAS as migratable. I did migration, NAS started but only 4 drives has been detected (and 2 NVMe for cache). Sata 5 and 6 (second raid array) has not been detected. 4) DS3622xsp Jun - found and migrated, working at the moment but... i cannot add extension for mu 10GbE card because of sum control error. I need HW acceleration... Benefits? I have latest DSM firmware... In my opinion, the easiest way is to apply a solution that forcibly adds the 5th and 6th SATA to the 3) DS920+. Originally, DS920+'s unique specification recommended to use only 4 drives, so using more than that is not recommended by jumkey and pocopipo. However, it was confirmed that 6 drives were recognized in the ds920+ device tree by dolbycat's test. I can't guarantee the stability, but it seems to be possible by applying a simple script. Would you like to try something like this? Quote Link to comment Share on other sites More sharing options...
shibby Posted June 21, 2022 Share #3895 Posted June 21, 2022 17 minutes ago, Peter Suh said: Would you like to try something like this? yes, i do Quote Link to comment Share on other sites More sharing options...
marigo Posted June 21, 2022 Share #3896 Posted June 21, 2022 (edited) I am using tinycore-redpill.v0.4.6.img to install DSM7.1 on Proxmox KVM. For storage I have attached 2 SATA drives. Everytime I use "./rploader.sh mapsata" I get incorrect output: "SataPortMap": "1", "DiskIdxMap": "10", When Build for "Appololake 918+" There are no drives detected. If I changed to an already working VM (Sataportmap: 62, DiskIdxMap:0002) Then only one drive is working. Am I doing something wrong? Edited June 21, 2022 by marigo Quote Link to comment Share on other sites More sharing options...
flyride Posted June 21, 2022 Share #3897 Posted June 21, 2022 Yes, something is wrong. You'll need to post more information about your hardware (motherboard, any disk controllers) and the output from satamap if you'd like some advice. Be sure that you "update" and "fullupgrade" prior to running satamap Quote Link to comment Share on other sites More sharing options...
Peter Suh Posted June 21, 2022 Share #3898 Posted June 21, 2022 (edited) 5 hours ago, shibby said: yes, i do In DS920+, the script was modified so that 6 built-in SATA can be used in jumkey's dynamic dtb method. Build the loader with the command below ./my.sh DS920+J jumkey noconfig noclean with the ll command Check the existence of model.dtb file ll /home/tc/redpill-load/custom/extensions/jumkey.qjs.dtb/ds920p_42218 with cat command Double-check that the following contents are printed. cat /home/tc/redpill-load/custom/extensions/jumkey.qjs.dtb/ds920p_42218/install_rd.sh Spoiler #!/bin/sh tar -zxvf patch.tar.gz # install dtc chmod +x etc cp dtc /usr/sbin/dtc # download 6 ports dtb file for ds920p #echo $PLATFORM_ID if [ "${PLATFORM_ID}" = "ds920p_42218" ]; then echo "copy ds920 6 ports model.dtb to /etc.defaults" cp -vf model.dtb /etc.defaults/model.dtb fi # copy file if [ ! -f model_${PLATFORM_ID%%_*}.dtb ]; then # Dynamic generation ./dtc -I dtb -O dts -o output.dts /etc.defaults/model.dtb qjs --std ./dts.js output.dts output.dts.out if [ $? -ne 0 ]; then echo "auto generated dts file is broken" exit 0 fi ./dtc -I dts -O dtb -o model_r2.dtb output.dts.out cp -vf model_r2.dtb /etc.defaults/model.dtb cp -vf model_r2.dtb /var/run/model.dtb else cp -vf model_${PLATFORM_ID%%_*}.dtb /etc.defaults/model.dtb cp -vf model_${PLATFORM_ID%%_*}.dtb /var/run/model.dtb fi If the result is even slightly wrong with this part, only 4 of the 6 ports will work. Edited June 21, 2022 by Peter Suh 1 Quote Link to comment Share on other sites More sharing options...
sam juan Posted June 21, 2022 Share #3899 Posted June 21, 2022 i still have TCRP 0.4.6 in my 2 boxes (no issues so far), it is worth to upgrade to TCRP 0.8 or maybe TCRP 0.9? tnx Quote Link to comment Share on other sites More sharing options...
Deniska Posted June 21, 2022 Share #3900 Posted June 21, 2022 (edited) В 07.06.2022 в 00:18, flyride сказал: There are different methods of making NVMe functional depending on the platform. I doubt all combinations have been tested so you may need to experiment. On DS918+, lib file needs to be patched. On DS3622xs+, there is a configuration file for the NVMe PCIe addresses DS3617xs is probably like DS3622xs+ DVA3221 method is not known, although I saw a post saying no lib file so it may be configuration file like DS3622xs+ On DS920+ and DS1621+, NVMe is supposed to be configured with Device Tree. If the Device Tree patchdtc script that is part of the loader build gets it wrong, DSM may not find it. Underlying Linux will probably see it, but DSM will not. This command reports detailed information about the NVMe PCIe address: udevadm info /dev/nvme0n1 You should review the Device Tree configuration and see if it is consistent with what is returned by udevadm. https://xpenology.com/forum/topic/62894-only-hdd-in-bay-1-are-found-by-storage-manager/#comment-285068 If necessary, you can edit the Device Tree manually but it is not fun: https://xpenology.com/forum/topic/62894-only-hdd-in-bay-1-are-found-by-storage-manager/?do=findComment&comment=285075 You could try the lib file and configuration file methods, although I doubt they will work for DS1621+ @flyride thank you for discovery nvme disk using as volume. I have tried lunch nvme as volume on DS1621+ but it doesn't work properly. I have done step back and installed DS920+ with extensions i8125 and e1000e for 2 NIC and acpid. And i have updated it for DSM 7.1-42661 Update 2 And finally all work perfect on AsRock H570-itx/ac, i5-10400, 16Gb, NVME disk. And nvme disk work as basic volume properly. Second NIC work too! Thanks guys for redpill loader, extensions and support! P.S. I've checked serial number in Synology account and it marked as invalid. I will look for another serial number. Edited June 21, 2022 by Deniska Adding P.S. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.