Jump to content
XPEnology Community

XPEnology DS3612xs DSM 4.2 build 3211++ (repack v1.2)


Recommended Posts

Yesterday I tried all USB ports (MB USB2,USB3, USB3 PCI CARD, CARD Reader with USB3) ... on my SYNOLOGY & they do not work.

 

These is also the reason, why UPS is not recognized .

 

You mean nothing append when you plug an usb device ?

I tested USB on two computer with external drive, and it's detected (mount as esata) and available on dsm. Printers are detected. Keyboard is working. (no UPS for testing :sad:)

 

 

Hi Trantor!

 

Thank you for noting my msg, though I am afraid I was talkig about different drivers - aacraid for SAS/SATA RAID Adapters rather than HBAs, or I completely misunderstand something?

 

PS: would enabling CONFIG_DEVPTS_MULTIPLE_INSTANCES allow virtual port creation to communicate with synobios? If so please enable too.

 

My bad forgot to build AACRAID driver, will be included in next update. No idea with CONFIG_DEVPTS_MULTIPLE_INSTANCES.

 

Trantor,

 

I just ordered a 24bay Supermicro system from eBay.

http://www.ebay.com/itm/171078773991?ss ... 1497.l2649

 

http://www.supermicro.com/aplus/motherb ... 8dme-2.cfm

The Supermicro H8DME-2 motherboard in this system contains the following.

- nVidia MCP55 Pro SATA2 3.0Gbps Controller

- nVidia MCP55 Pro Chipset Dual-port LAN / Ethernet Controller

 

Additionally, it also comes with 3x Supermicro AOC-SAT2-MV8 SATA cards (Marvell Hercules-2 Rev. C0 SATA host controller)

http://www.supermicro.com/products/acce ... t2-mv8.cfm

 

1) Does the current release contain the SATA and Ethernet drivers for the nVidia MCP55Pro?

2) Does it contain the driver to support Marvell Hercules host controller?

 

Thanks. I'll be testing it out once I get the hardware. I'm just curious about the compatibility prior to receive the hardware.

 

Nvidia network is supported as the marvell/nvidia sata controller.

Link to comment
Share on other sites

Can I use this repack to install it on 2 x 2TB disks in mirror using vmware workstation or player?

 

I would like to install XPenology only on these 2 disks. Please look at my post http://xpenology.com/forum/viewtopic.php?f=2&t=1041 for more info.

 

Thx!

 

Yes you can use this repack with VMware, but ESXi is recommended instead of workstation (this esxi thread for more infos).

Link to comment
Share on other sites

You mean nothing append when you plug an usb device ?

 

YES ... I see only my 6 disc > https://dl.dropboxusercontent.com/u/34829066/Synology/Slike/HDD.jpg

 

I did try 4 different USB FLASH & UPS on this ports:

 

- USB2 & USB3 on motherboard

- USB3 & SD card reader, wich is connected to USB3 on MB (inside)

- PCIex card with USB3

 

but, nothing works by me ... with 4.1-2668_1.2 & up, this stuff works.

Edited by Guest
Link to comment
Share on other sites

Can I use this repack to install it on 2 x 2TB disks in mirror using vmware workstation or player?

 

I would like to install XPenology only on these 2 disks. Please look at my post http://xpenology.com/forum/viewtopic.php?f=2&t=1041 for more info.

 

Thx!

 

Yes you can use this repack with VMware, but ESXi is recommended instead of workstation (this esxi thread for more infos).

 

 

My intention was to run this on esxi but the problem is I cannot install esxi on my hardware because to the onboard network intel wg-i217v adapter..

I tried to add the drivers for this adapter with esxi customizer but no luck..

 

Anyone already succeeded in this?

Link to comment
Share on other sites

My bad forgot to build AACRAID driver, will be included in next update. No idea with CONFIG_DEVPTS_MULTIPLE_INSTANCES.

 

Thanks! just please take the latest from Adaptec's site http://www.adaptec.com/en-us/speed/raid/aac/linux/aacraid-linux-src-1_2_1-30200_tgz.htm

 

As to CONFIG_DEVPTS_MULTIPLE_INSTANCES=y seems to be needed to create another virtual port, link it to one synobios is using and try cheating it https://www.kernel.org/doc/Documentation/filesystems/devpts.txt. Please enable this for experimenting.

Link to comment
Share on other sites

My bad forgot to build AACRAID driver, will be included in next update. No idea with CONFIG_DEVPTS_MULTIPLE_INSTANCES.

 

Thanks! just please take the latest from Adaptec's site http://www.adaptec.com/en-us/speed/raid/aac/linux/aacraid-linux-src-1_2_1-30200_tgz.htm

 

As to CONFIG_DEVPTS_MULTIPLE_INSTANCES=y seems to be needed to create another virtual port, link it to one synobios is using and try cheating it https://www.kernel.org/doc/Documentation/filesystems/devpts.txt. Please enable this for experimenting.

 

Just build latest aacraid driver from adaptec's site.

aacraid driver also support IBM ServeRAID adapter so I temporally disable the buil-in driver (ips). (FrankGNL please give feedback about this)

 

Download this and replace rd and zImage on your flash drive : http://xpenology.trantor.be/aacraid-v1.2.1_rd_zImage.7z

 

 

@interested : Did the USB work with the orignial 4.2-302 build from odie ?

 

PS : I leave home tomorrow for vacation for a week, so no update until august 20th ^^

Link to comment
Share on other sites

@interested : Did the USB work with the orignial 4.2-302 build from odie ?

 

Answer is NO.

 

Becouse of this, I did buy one new D-Link 2-Port USB 3.0 PCI Express Card (DUB-1310), but it does not work.

 

I dont know what is inside your ver. 4.1-2668(1.2-1.3a), but it works.

 

Please tell me how can I help you to resolve this ... deficiency ???

Edited by Guest
Link to comment
Share on other sites

@interested : Did the USB work with the orignial 4.2-302 build from odie ?

 

Answer is NO.

 

Becouse of this, I did buy one new D-Link 2-Port USB 3.0 PCI Express Card (DUB-1310), but it does not work.

 

I dont know what is inside your ver. 3.1-2668(1.2-1.3a), but it works.

 

Please tell me how can I help you to resolve this ... deficiency ???

 

Did any 4.2 version have USB working on your hardware ?

Link to comment
Share on other sites

I dont know what is inside your ver. 3.1-2668(1.2-1.3a), but it works.

 

Nothing that's not in the 4.2.

When I ask about other 4.2 build I mean like RS3413xs+ DSM 4.2-3211 x86 or DS3612xs_4.2-3211_x64.

 

To be clear, as you said when you plug for example USB sick nothing append ? even on the xpenology screen ?

Try command : tail -f /var/log/message and plug something in USB ports. (some input should appear)

 

Does the plugged device is even powered ? What's about a standard USB keyboard ?

Link to comment
Share on other sites

I am almost sure, that I did tested all this version, but without any luck.

 

Yes, when I plug in USB Stick nothing append, not even Keyboard on the xpenology screen.

 

I did put in USB and type this command > tail -f /var/log/messages

 

SYNOLOGY> tail -f /var/log/messages
Aug 11 20:27:36 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:27:55 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:33:20 ssrotated: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:33:26 ssrotated: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:37:46 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:38:08 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:38:12 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:38:18 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:38:23 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587
Aug 11 20:38:40 ssd: smtp.c (381) Failed to connect to smtp.gmail.com:587

 

Plugged device flashes for half a second, but that's all.

 

 

This is the screen after reboot > https://dl.dropboxusercontent.com/u/34829066/Synology/Slike/screen%20after%20reboot.JPG

 

Here are two logs, if it helps:

 

- messages > https://dl.dropboxusercontent.com/u/34829066/Synology/Datoteke/Logs/messages

- dmesg.boot > https://dl.dropboxusercontent.com/u/34829066/Synology/Datoteke/Logs/dmesg.boot

 

TNX.

Link to comment
Share on other sites

Ok went log hunting and right before the DSM crashes, by crash I mean no external access but the computer is still powered up. it prints this

 

Aug 12 06:04:35 inetd[7583]: accept (for printer) : Invalid argument

 

and all of the lines will be exactly the same all 1301 of them....

There is no printer hooked up nor has there ever been.

Link to comment
Share on other sites

 

Does two VM disks, are they IDE or SCSI?

 

Does spindown work for you?

 

For me installation is working, but when i shutdown the VM, attach my LSi raidcontroller, turn it on, it will auto power off the vm after 1 minute.

 

yes both disk are IDE and spin down works, auto power off happened to me when there was no support for the card.

 

Is your card in IT Mode?

Does spin down works even if you create a volume on the disks, why i ask, i would like to buy a LSI SAS 2008 and flash it to IT mode.

Thanks in advance

 

Regards Frank

Link to comment
Share on other sites

thanks for sharing!

 

i just successfully install this version of xpenology into my old computer directly(not vbox or vmware),

without out any problem.

 

here is my hardware specs for ppl wanna install.

 

CPU: AMD Athlon 64 X2 4000+

MB: MIS 7309

NIC: TP-Link Gigabit PCI Express TG-3468 with realtek chip

HDD: sata2 device *2

 

boot with USB drive and everything goes smoothly !

Link to comment
Share on other sites

Hi,

 

I'm trying to install this repack in ESX but still no luck..

 

I did the following:

 

- Converted the .img to .vmdk with starwind (IDE, pre-allocated)

- Mapped my 2TB disk as RDM as in the idiot's guide for install on esx

- followed the idiot's guide to create VM, added the boot image as an IDE drive, and the RDM as a Paravirtual SCSI drive

- boot the VM

- With synology assistant search, right click and install

- during install the device will get a reboot

- after this reboot i get the grub error 22

- shut down VM

- deleted the disk with boot vmdk

- reuploaded the boot vmdk

- assigned it to the VM

- boot the VM

- the installation completed after the countdown (think 600 sec)

- tried to browse to the IP I gave during install

- got the error it can not connect to the diskstation

- assistant finds the DS but says configuration lost

 

What am I doing wrong here?

My pc is directly connected to the esx server. Pc is also connected to a wireless router, different subnet but this should not matter..

 

Plz help!

Thx

Link to comment
Share on other sites

Trantor.

 

I got my new server. NVidia NIC and SATA works with this build. However the Marvell SATA cards do not. Whenever I have the Marvell SATA cards installed, the boot-up process would not complete.

 

I would get this error continuously during bootup

 

Screen Shot 2013-08-15 at 9.08.00 PM.png[/attachment]

593ef3ad62b0d_ScreenShot2013-08-15at9_08_00PM.png.5dbd2f8fd6f9baf54f8aa599c755be1a.png

marvel-bootup.png.0fdd3e401581540f0741622cd09f0a2b.png

Link to comment
Share on other sites

Trantor.

 

I got my new server. NVidia NIC and SATA works with this build. However the Marvell SATA cards do not. Whenever I have the Marvell SATA cards installed, the boot-up process would not complete.

 

I would get this error continuously during bootup

 

Screen Shot 2013-08-15 at 9.08.00 PM.png[/attachment]

 

 

I have to report the same problem is present with the Rocketraid 1742/1740 PCI-based controllers, also based on a Marvell SATA-controller, specifically the 88SX6042-chip.

 

The problem is *not* present on a generic PCIe-based controller with the Marvell 88SX7042-chip, nor on the Promise TX4310 PCI-based controller that has a Marvell 88SX5041.

 

So clearly one of the Marvell-modules is broken...?

 

I seem to recall that I previously had the Rocketraid 1742 working correctly, with an early build of QNOLOGY from XVortex on the QNAP-site...

 

Edit: Screendumps of boot up screen:

http://peecee.dk/upload/view/419198

http://peecee.dk/upload/view/419199

http://peecee.dk/upload/view/419200

http://peecee.dk/upload/view/419201

Link to comment
Share on other sites

@Kanedo and @colombodk :

The sata_mv driver is built-in the offical syno kernel and is modified by synology.

I tried to build it as module but the machine boot and shutdown itself afert 1min....

I assume you test my 4.1 build and have the same issue ?

If someone have enought knowledge to maybe patch sata_mv.c

 

@T-REX-XP :

Can you please give me more informations about ACPI driver to include and LCDPROC ?

 

@tsygam and @FrankGNL :

Did the latest aacraid driver solved your issue ?

 

@everyone ^^ :

Can you confirm me that the issue with external usb detected as esata is present in the odie's 4.2-3202 build ?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...