dvbmaniak Posted January 28, 2022 Share #3601 Posted January 28, 2022 12 hours ago, NoFate said: guys, is there something wrong with the 6.2.4 loader? I have an Hp Gen 8 , with esxi, the bootlader is on sata disk 0:0 , my extra hard disk is at sata disk 0:0 i have below configured : "SataPortMap": "2", "DiskIdxMap": "00" if i do this : sudo ./rploader.sh build bromolow-7.0.1-42218 i can perfect install a DSM 7 system, it works perfect had it running for a few days, during .pat upload the installed told me DSM is going to be installed on DISK 2 i do the exact same process, now with this command, a clean host in esxu sudo ./rploader.sh build bromolow-6.2.4-25556 i upload that specific pat file, again i get the message that it will install on disk 2 , it completes to 100% i do a reboot, but its back at the setup start again?? for a new .pat file upload? whats wrong? After this reboot, i'm back at point 1 what could be wrong? the same problem Link to comment Share on other sites More sharing options...
NoFate Posted January 28, 2022 Share #3602 Posted January 28, 2022 Just now, dvbmaniak said: the same problem Ah, that's good So there must be somethng wrong with the 6.2.4 loader Link to comment Share on other sites More sharing options...
AlexFullmoon Posted January 28, 2022 Share #3603 Posted January 28, 2022 As I missed a couple months of discussions, can I ask about status (and main problems) for specific variants? Besides "public alpha, not ready for production", I know that. 3615 has problems with Docker/databases both baremetal and VMs, right? 3617? 918? Link to comment Share on other sites More sharing options...
buggy25200 Posted January 28, 2022 Share #3604 Posted January 28, 2022 (edited) Hello, DSM 6.2.4 update 4 is out! https://www.cachem.fr/synology-dsm-6-2-4-25556-update-4/ No kernel modification so Update from loader make with 624-25556u2 should work (Same sha256sum for zimage platform918+/3617xs/3615xs) Edited January 28, 2022 by buggy25200 Link to comment Share on other sites More sharing options...
MastaG Posted January 28, 2022 Share #3605 Posted January 28, 2022 I'm running DS3615xs DSM 7.0.1-42218 on my MicroServer Gen8 G1610T. I've compiled it from source a while ago and I remember it took me some trouble to figure out how to add a repository for the ethernet drivers. Anyways it has been running rock solid up until now, surveillance station, docker + portainer and even a Windows 10 VM and I'm very happy with it. Now I believe update DSM 7.0.1-42218 Update 1 and 2 are out now. What's the best way to build a new image (which includes the ethernet driver)? 2 Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 29, 2022 Share #3606 Posted January 29, 2022 14 hours ago, MastaG said: I'm running DS3615xs DSM 7.0.1-42218 on my MicroServer Gen8 G1610T. I've compiled it from source a while ago and I remember it took me some trouble to figure out how to add a repository for the ethernet drivers. Anyways it has been running rock solid up until now, surveillance station, docker + portainer and even a Windows 10 VM and I'm very happy with it. Now I believe update DSM 7.0.1-42218 Update 1 and 2 are out now. What's the best way to build a new image (which includes the ethernet driver)? What was your process of adding your ext to the kernel? I've check rp-ext by pocopico and he only have some of the drivers I need for my device to work properly. Dell Poweredge T320 H310 LSI SAS2008 Megaraid SAS card. 3615 doesn't like the megaraid_sas drive so it never boots when I add this driver. It will on 3617, but trying to build it as of late is crazy. The pat download link is down most of the time during the night. Now some drivers like megaraid_sas won't download when pulled to the build. Anyway, I figured if I could added them to the kernel myself, what I need, then it would work. Any help would be awesome Link to comment Share on other sites More sharing options...
Hackaro Posted January 29, 2022 Share #3607 Posted January 29, 2022 On 1/27/2022 at 4:08 PM, PincoPalla said: Hello everyone as I wrote that I would have done a few days ago today I upgraded (migrated) the DSM from 6.2.3 up3 to 7.0.1 (42218) up2 baremetal from image redpill-DS918 + _7.0.1-42218_b1635406499.img, everything went right everything works correctly (or almost ..); as I feared, the system no longer sees me the two NVMe cards that I use for the cache which therefore I cannot mount, someone knows and wants to help me ??? Are the patches used for version 6.2.3 okay or are there others ??? Thank you Ciao PincOPallA, it seems to me that something has been written about the NVMe support between page 80 and page 90 on this thread... you should dig further in those pages. If you found something please re-post it here to us, because I'm very interested. Furthermore Could you be so kind to tell us: what is not working correctly? far more important which is your detailed list of BareMetal hardware? Thank you! Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 30, 2022 Share #3608 Posted January 30, 2022 Hello guys. Im trying to get 6.2.4 or higher installed on a Dell Poweredge T320. The problem that Im having is a lot of the drivers I needed to be installed are not included in the tinycore img or not in pocopico's rp-ext. Plus currently the url for the drivers/modules is broken. Not able to add drivers. Is it possible to manually add your own modules and if so how? See attachments below, maybe it can help someone to help me. Thanks. lspci dmesg kmod list Link to comment Share on other sites More sharing options...
Kaneske Posted January 30, 2022 Share #3609 Posted January 30, 2022 I read about GitHub has changed their Path structure. Doesn’t it work with adding the extension with new url to the jsons? 1 Link to comment Share on other sites More sharing options...
Piteball Posted January 30, 2022 Share #3610 Posted January 30, 2022 Hello guys. Im trying to get 6.2.4 or higher installed on a Dell Poweredge T320. The problem that Im having is a lot of the drivers I needed to be installed are not included in the tinycore img or not in pocopico's rp-ext. Plus currently the url for the drivers/modules is broken. Not able to add drivers. Is it possible to manually add your own modules and if so how? See attachments below, maybe it can help someone to help me. Thanks.lspci dmesg kmod listYour best bet would be to ask pocopico nicelly if he can compile drivers for the missing devices and to his rp-ext tree. In Linux drivers are bound to the Linux kernel so you need to recompile using kernel sources used in the specific DSM version and emulated Synology hardware. Skickat från min LE2113 via Tapatalk 1 Link to comment Share on other sites More sharing options...
IG-88 Posted January 30, 2022 Share #3611 Posted January 30, 2022 2 hours ago, Dvalin21 said: Hello guys. Im trying to get 6.2.4 or higher installed on a Dell Poweredge T320. The problem that Im having is a lot of the drivers I needed to be installed are not included in the tinycore img or not in pocopico's rp-ext. Plus currently the url for the drivers/modules is broken. Not able to add drivers. Is it possible to manually add your own modules and if so how? See attachments below, maybe it can help someone to help me. Thanks. it is possible to add manually if you look into it how its done also its way better to get help if you deliver specific information amount you hardware and what you are looking for like having a complete lspci or dmsg from system running the drivers properly (like a live linux) as you shortend your logs and information there is only a limited amount of whats to say onboard nic dell t320, Broadcom 5720 1GbE Dual Port LOM, -> tg3.ko from the lspci part, "Subsystem: Device 1028:1f4e" https://pci-ids.ucw.cz/read/PC/1000/0073/10281f4e -> Perc H310, sas2008 based -> mpt2sas.ko/mpt3sas.ko, there are native to 3615/3617 and usually work ootb with these also all this drivers are already there, so you just need to add them properly https://github.com/pocopico/3.10.108-modules https://github.com/pocopico/4.4.180plus-modules https://github.com/pocopico/4.4.180plus-broadwell for the tg3.ko there is also firmware needed, looks like this in jun's loaders rc.modules and there is a parallel "firmware" folder parallel to the modules folder EXTRA_FIRMWARES="tigon/tg3_tso5.bin tigon/tg3_tso.bin tigon/tg3.bin tigon/tg357766.bin" in extra.lzma \usr\lib\firmware\tigon\ (i have not looked into how redpill loader handles firmware compared to jun's) dell and hpe often used other broadcom nic's, they would most likely need bnx2.ko or bnx2x.ko and will need firmware too Link to comment Share on other sites More sharing options...
anibalin Posted January 30, 2022 Share #3612 Posted January 30, 2022 On 1/26/2022 at 11:21 AM, zahni said: @eldi: I have exactly the same issue and havn't found any help. I've you found a solution, I would be happy. Hey guys. I have found, at least on my case, that when the bootloader starts it should load the sata option (second one) and not the first one (default one) usb. Link to comment Share on other sites More sharing options...
nickhx Posted January 30, 2022 Share #3613 Posted January 30, 2022 (edited) Has anyone had any luck getting 7.0.1 on an 918+ with a LSI PCI passthrough card working on ESXi? I can install and boot ok, and DSM can see the drives fine. However, it doesn't seem able to read the SMART data so the Storage Pool is showing error messages which I can't clean. Edited January 30, 2022 by nickhx Link to comment Share on other sites More sharing options...
IG-88 Posted January 30, 2022 Share #3614 Posted January 30, 2022 (edited) On 1/30/2022 at 6:31 PM, nickhx said: Has anyone had any luck getting 7.0.1 on an 918+ with a LSI PCI passthrough card working on ESXi? I can install and boot ok, and DSM can see the drives fine. However, it doesn't seem able to read the SMART data so the Storage Pool is showing error messages which I can't clean. you can read about that problem in the additional driver section 6.2.3 extra.lzma, when using "clean" scsi/sas kernel driver you end up like that, with jun's sas for 918+ it ended in smart/sn working for disks but killing the raid when using hdd power management like spin down when using both, syno's scsi/sas support drivers and device drivers (like in 3617) it does work properly, so using 3617 would fix your problems - but with 7.0 there might be a new option because 3617 is now also kernel 4.4 like 918+, it would be possible (with some uncertainty's) to transplant the 3617 scsi/sas support driver and mpt2sas/mpt3sas drivers into 918+, kind of dirty trickery but if it works out ... - same might also be possible the other way around with the i915 drivers (maybe), so having i915 support in 3617 with its 16 thread/core kernel, or even nvme support for 3617 as code and base are all the same now? (but that might need lots of tinkering and testing) at least that is the kind of plans i would have when dealing with 7.0 and drivers and the missing kernel/driver source, atm i'm in no hurry for these things, but it gets more interesting with tinycore and @pocopico 's efforts but at some point it might be easier to use the redpill loader source to adapt to a better/newer base then 3615/3617/918+ - but that's beyond my capabilities i did some suggestions here for a new base (i guess beside the coding it needs some reverse engineering about the hardware that is checked to implement the needed fake psi id's) https://xpenology.com/forum/topic/38603-suggestions-for-units-to-have-a-loader-for-with-70/ Edited January 31, 2022 by IG-88 1 Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 30, 2022 Share #3615 Posted January 30, 2022 (edited) 12 hours ago, IG-88 said: it is possible to add manually if you look into it how its done also its way better to get help if you deliver specific information amount you hardware and what you are looking for like having a complete lspci or dmsg from system running the drivers properly (like a live linux) as you shortend your logs and information there is only a limited amount of whats to say onboard nic dell t320, Broadcom 5720 1GbE Dual Port LOM, -> tg3.ko from the lspci part, "Subsystem: Device 1028:1f4e" https://pci-ids.ucw.cz/read/PC/1000/0073/10281f4e -> Perc H310, sas2008 based -> mpt2sas.ko/mpt3sas.ko, there are native to 3615/3617 and usually work ootb with these also all this drivers are already there, so you just need to add them properly https://github.com/pocopico/3.10.108-modules https://github.com/pocopico/4.4.180plus-modules https://github.com/pocopico/4.4.180plus-broadwell for the tg3.ko there is also firmware needed, looks like this in jun's loaders rc.modules and there is a parallel "firmware" folder parallel to the modules folder EXTRA_FIRMWARES="tigon/tg3_tso5.bin tigon/tg3_tso.bin tigon/tg3.bin tigon/tg357766.bin" in extra.lzma \usr\lib\firmware\tigon\ (i have not looked into how redpill loader handles firmware compared to jun's) dell and hpe often used other broadcom nic's, they would most likely need bnx2.ko or bnx2x.ko and will need firmware too I've tried the mpt2sas and 3, they didn't work. What did seem to work was the megaraid_sas. I would be able to get all the way to the install, but get to 56% and then get it was a corrupt file or something. Now not sure what's going on as when I go to add ext, keep getting 404 not found. My main issue is the the sas raid card and getting it to work right. When Im able, ill go back and try mpt2 and 3 again. I did install them separately, maybe I need to install both. Edited January 30, 2022 by Dvalin21 Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 30, 2022 Share #3616 Posted January 30, 2022 14 hours ago, Kaneske said: I read about GitHub has changed their Path structure. Doesn’t it work with adding the extension with new url to the jsons? Ive tried that. Basically changing where it says master to main. Still got the same issue. Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 31, 2022 Share #3617 Posted January 31, 2022 15 hours ago, IG-88 said: it is possible to add manually if you look into it how its done also its way better to get help if you deliver specific information amount you hardware and what you are looking for like having a complete lspci or dmsg from system running the drivers properly (like a live linux) as you shortend your logs and information there is only a limited amount of whats to say onboard nic dell t320, Broadcom 5720 1GbE Dual Port LOM, -> tg3.ko from the lspci part, "Subsystem: Device 1028:1f4e" https://pci-ids.ucw.cz/read/PC/1000/0073/10281f4e -> Perc H310, sas2008 based -> mpt2sas.ko/mpt3sas.ko, there are native to 3615/3617 and usually work ootb with these also all this drivers are already there, so you just need to add them properly https://github.com/pocopico/3.10.108-modules https://github.com/pocopico/4.4.180plus-modules https://github.com/pocopico/4.4.180plus-broadwell for the tg3.ko there is also firmware needed, looks like this in jun's loaders rc.modules and there is a parallel "firmware" folder parallel to the modules folder EXTRA_FIRMWARES="tigon/tg3_tso5.bin tigon/tg3_tso.bin tigon/tg3.bin tigon/tg357766.bin" in extra.lzma \usr\lib\firmware\tigon\ (i have not looked into how redpill loader handles firmware compared to jun's) dell and hpe often used other broadcom nic's, they would most likely need bnx2.ko or bnx2x.ko and will need firmware too Sorry one more thing. The tg3 works fine (that Im aware of. Im at least able to find the device) The modules I have was from https://github.com/pocopico/4.4.180plus-broadwell If you look at my kmod you will see that the megaraid_sas is being used by 9 devices. (megaraid_sas 72750 9) Mptbase is dependent on mptctl, mptsas, mptspi, mptscsih and is used by 4 devices. Pocopico is missing some of the mpt modules in rp-ext like mptclt and mptscsih. He modified(compiled) mptsas and from what I could tell with adding or merged some other mpt, but my device dont seem to like it. Either way, this kmod, dmesg, lspci was pulled from 6.2.3 DSM3617xs on the device and have zero issues with it. I guess what I'm saying it worked better with all of the modules being installed (even though there were many werent used). I can understand the idea with the new approach, but it seems to be little harder at least for a lot dell servers and especially LSI SAS cards. I can see my motherboard sata ports with no issue, but nothing is connected to them so its not helpful Link to comment Share on other sites More sharing options...
painkiller895 Posted January 31, 2022 Share #3618 Posted January 31, 2022 On 1/20/2022 at 2:10 PM, miicker said: I just found this topic, I thought DSM 7 (or 6.2.4) was still impossible, then I looked into the update topic and I saw that people successfully installed DSM 7 on their NAS using RedPill. I have a baremetal system that runs Juns loader v1.04b (DS918+). I have an Intel Pentium G4560 with 5 disks installed. Can I use RedPill loader to install DSM 7? And if so, will I be able to keep my DSM settings and docker containers etc. I searched already on this site and on Google but could not find a proper tutorial on how to do this, is there anyone here that can help? If you have 12TB of data that's important to you don't do it unless you backup your stuff first. This is still in beta, try building a new system with the redoill loader and then transfer your data over is what I would do.... Link to comment Share on other sites More sharing options...
IG-88 Posted January 31, 2022 Share #3619 Posted January 31, 2022 19 hours ago, Dvalin21 said: What did seem to work was the megaraid_sas. is you controller in IR Mode? R like Raid? it suposed do be IT Mode like initiator target mode, where all disks are just single disks without any raid options its usually to be seen in the controllers bios 16 hours ago, Dvalin21 said: I can understand the idea with the new approach, but it seems to be little harder at least for a lot dell servers and especially LSI SAS cards. in case of 3617 syno had newer drivers in place apart from the one in the kernel (dsm 6.2.x) and i favored syno's own drivers over ones made from not matching kernel code i guess at least for 7.0 3617 it would be better to use syno's sas and mpt drivers in the loader, but that needs some tinkering like a custom.gz manually made up like the extra.lzma atm i'm not doing much with 7.0 as its kind of to new to have it on my system, i'm just poking a little bit here and there for now to see where its going 16 hours ago, Dvalin21 said: I can see my motherboard sata ports with no issue, but nothing is connected to them so its not helpful ahci is default in all syno kernels we have, kind of a safe choice for all units as its present in all and switching between dsm types is possible without worrying about drivers 1 Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 31, 2022 Share #3620 Posted January 31, 2022 1 hour ago, IG-88 said: is you controller in IR Mode? R like Raid? it suposed do be IT Mode like initiator target mode, where all disks are just single disks without any raid options its usually to be seen in the controllers bios in case of 3617 syno had newer drivers in place apart from the one in the kernel (dsm 6.2.x) and i favored syno's own drivers over ones made from not matching kernel code i guess at least for 7.0 3617 it would be better to use syno's sas and mpt drivers in the loader, but that needs some tinkering like a custom.gz manually made up like the extra.lzma atm i'm not doing much with 7.0 as its kind of to new to have it on my system, i'm just poking a little bit here and there for now to see where its going ahci is default in all syno kernels we have, kind of a safe choice for all units as its present in all and switching between dsm types is possible without worrying about drivers Thank you so much for answering all my questions. I really appreciate it. I can understand with Dsm 7, still new and all that. I would try 6.2.4, but I still have to go through tinycore correct? Also thank you for all past, present, and future assistance to this community. You and many others are very much appreciated. 1 Link to comment Share on other sites More sharing options...
IG-88 Posted January 31, 2022 Share #3621 Posted January 31, 2022 1 hour ago, Dvalin21 said: I would try 6.2.4, but I still have to go through tinycore correct? maybe not, but that's extremely new (<24h old) and not much tested yet https://xpenology.com/forum/topic/56025-juns-ds918-loader-modified-for-dsm-624/ 2 Link to comment Share on other sites More sharing options...
Dvalin21 Posted January 31, 2022 Share #3622 Posted January 31, 2022 10 minutes ago, IG-88 said: maybe not, but that's extremely new (<24h old) and not much tested yet https://xpenology.com/forum/topic/56025-juns-ds918-loader-modified-for-dsm-624/ Thanks for this. I will have to give this a try at some point. Link to comment Share on other sites More sharing options...
pipsen Posted February 1, 2022 Share #3623 Posted February 1, 2022 Did anybody already succeed to compile kernel modules for DSM 7.0.1 for lm-sensors? hwmon-vid.ko nct6775.ko Here are only modules for DSM 6.2.3: Link to comment Share on other sites More sharing options...
Amoureux Posted February 1, 2022 Share #3624 Posted February 1, 2022 who knows how fix it ? dmesg | grep error [ 3.561654] intel-lpss: probe of 0001:00:16.0 failed with error -22 [ 3.568502] intel-lpss: probe of 0001:00:18.0 failed with error -22 [ 3.575360] intel-lpss: probe of 0001:00:19.0 failed with error -22 [ 3.582289] intel-lpss: probe of 0001:00:19.2 failed with error -22 [ 8.743494] ahci: probe of 0001:01:00.0 failed with error -22 [ 8.749644] ahci: probe of 0001:00:12.0 failed with error -22 [ 26.346195] xhci_hcd: probe of 0001:00:15.0 failed with error -16 [ 29.881245] usb 1-12: device descriptor read/64, error -71 [ 30.111253] usb 1-12: device descriptor read/64, error -71 [ 30.471270] usb 1-12: device descriptor read/64, error -71 [ 30.701291] usb 1-12: device descriptor read/64, error -71 [ 31.866318] usb 1-12: device not accepting address 6, error -71 [ 32.416340] usb 1-12: device not accepting address 7, error -71 [ 41.252764] igb: probe of 0001:02:00.0 failed with error -5 [ 41.252768] igb: probe of 0001:03:00.0 failed with error -5 res 40/00:10:00:9d:0e/00:00:00:00:00/40 Emask 0x50 (ATA bus error) res 40/00:10:00:9d:0e/00:00:00:00:00/40 Emask 0x50 (ATA bus error) res 40/00:10:00:9d:0e/00:00:00:00:00/40 Emask 0x50 (ATA bus error) res 40/00:10:00:9d:0e/00:00:00:00:00/40 Emask 0x50 (ATA bus error) [ 74.421735] ata7: link reset sucessfully clear error flags res 40/00:38:00:8c:b5/00:00:00:00:00/40 Emask 0x50 (ATA bus error) res 40/00:38:00:8c:b5/00:00:00:00:00/40 Emask 0x50 (ATA bus error) res 40/00:38:00:8c:b5/00:00:00:00:00/40 Emask 0x50 (ATA bus error) [ 147.154767] ata7: link reset sucessfully clear error flags dmesg | grep failed [ 2.620571] redpill: module verification failed: signature and/or required key missing - tainting kernel [ 3.561654] intel-lpss: probe of 0001:00:16.0 failed with error -22 [ 3.568502] intel-lpss: probe of 0001:00:18.0 failed with error -22 [ 3.575360] intel-lpss: probe of 0001:00:19.0 failed with error -22 [ 3.582289] intel-lpss: probe of 0001:00:19.2 failed with error -22 [ 8.743494] ahci: probe of 0001:01:00.0 failed with error -22 [ 8.749644] ahci: probe of 0001:00:12.0 failed with error -22 [ 26.346195] xhci_hcd: probe of 0001:00:15.0 failed with error -16 [ 40.108495] systemd[1]: Cannot add dependency job for unit pkg-install-high-priority-builtin.service, ignoring: Unit pkg-install-high-priority-builtin.service failed to load: No such file or directory. [ 40.127555] systemd[1]: Cannot add dependency job for unit pkg-install-low-priority-builtin.service, ignoring: Unit pkg-install-low-priority-builtin.service failed to load: No such file or directory. [ 41.252764] igb: probe of 0001:02:00.0 failed with error -5 [ 41.252768] igb: probe of 0001:03:00.0 failed with error -5 [ 61.417339] ata7.00: failed command: READ FPDMA QUEUED [ 61.443123] ata7.00: failed command: READ FPDMA QUEUED [ 61.468662] ata7.00: failed command: WRITE FPDMA QUEUED [ 61.494397] ata7.00: failed command: READ FPDMA QUEUED [ 71.536095] ata7: COMRESET failed (errno=-16) [ 134.424600] ata7.00: failed command: READ FPDMA QUEUED [ 134.450331] ata7.00: failed command: READ FPDMA QUEUED [ 134.475936] ata7.00: failed command: READ FPDMA QUEUED [ 144.523120] ata7: COMRESET failed (errno=-16) Link to comment Share on other sites More sharing options...
plarkass Posted February 1, 2022 Share #3625 Posted February 1, 2022 Hello everyone, Stupid case butafter updating my synology to last 7.0.1 my acess is blocked. No any password in serial, web and SSH. Someone have a way to reset or open it again ? Link to comment Share on other sites More sharing options...
Recommended Posts