pocopico Posted September 7, 2021 Share #1051 Posted September 7, 2021 5 minutes ago, sbtec said: @pocopico Joining you in the ranks of the mighty HP Gen7, compiled 3615xs 7.01 from latest lkm/loader pair using syno toolkit. Have booted/installed on a blank hard drive. Rebooted and crashed deliberately a few times, still ok. In the process of installing some software and will continue testing, as per other posts here the Info Centre in Control Panel contains no detail in the General section. Previous install of 6.2.4 from earlier lkm/loader (see post Aug 1st) has been in use 24/7 until now. 😀 I actually feel lucky to even be able to install 7.01 on my G7 that for some reason refuses to die. 😂 Link to comment Share on other sites More sharing options...
sirdrug Posted September 7, 2021 Share #1052 Posted September 7, 2021 Hi! When i try to install on proxmox i had error mount md0 [ 119.952767] EXT4-fs (md0): mounting ext3 file system using the ext4 subsystem [ 120.016877] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 121.191939] <redpill/rtc_proxy.c:37> MfgCompatTime raw data: sec=9 min=1 hr=9 wkd=2 day=7 mth=8 yr=121 [ 121.193622] <redpill/rtc_proxy.c:95> Writing BCD-based RTC [ 121.194653] RTC time set to 2021-09-07 9:01:09 (UTC) [ 121.209845] EXT4-fs (md0): mounting ext3 file system using the ext4 subsystem [ 121.277528] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 121.392446] EXT4-fs (md0): mounting ext3 file system using the ext4 subsystem [ 121.402739] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 121.423260] EXT4-fs (md0): mounting ext3 file system using the ext4 subsystem [ 121.440052] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 121.515162] md0: detected capacity change from 2549940224 to 0 [ 121.516100] md: md0: set sdh1 to auto_remap [0] [ 121.516890] md: md0: set sdi1 to auto_remap [0] [ 121.517703] md: md0 stopped. [ 121.518220] md: unbind<sdh1> [ 121.521023] md: export_rdev(sdh1) [ 121.521535] md: unbind<sdi1> [ 121.525034] md: export_rdev(sdi1) [ 121.568367] md1: detected capacity change from 2147418112 to 0 [ 121.569287] md: md1: set sdh2 to auto_remap [0] [ 121.569996] md: md1: set sdi2 to auto_remap [0] [ 121.570701] md: md1 stopped. [ 121.571170] md: unbind<sdh2> [ 121.577035] md: export_rdev(sdh2) [ 121.577606] md: unbind<sdi2> [ 121.584056] md: export_rdev(sdi2) [ 124.686739] md: bind<sdh1> [ 124.687362] md: bind<sdi1> [ 124.688378] md/raid1:md0: active with 2 out of 16 mirrors [ 124.703310] md0: detected capacity change from 0 to 2549940224 [ 126.057168] EXT4-fs (md0): mounting ext3 file system using the ext4 subsystem [ 126.078430] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 127.766177] md: bind<sdh2> [ 127.767187] md: bind<sdi2> [ 127.767939] md/raid1:md1: active with 2 out of 16 mirrors [ 127.785579] md1: detected capacity change from 0 to 2147418112 [ 128.446373] EXT4-fs (md0): couldn't mount as ext3 due to feature incompatibilities [ 128.466030] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 128.554349] <redpill/rtc_proxy.c:222> Got an invalid call to rtc_proxy_set_auto_power_on [ 128.559532] EXT4-fs (md0): couldn't mount as ext3 due to feature incompatibilities [ 128.578612] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) Link to comment Share on other sites More sharing options...
Aigor Posted September 7, 2021 Share #1053 Posted September 7, 2021 28 minutes ago, shibby said: I tested fresh install 7.0.1 with redpill on my bare metal - it works. Now i wanted to migrate from 6.2.3 to 7.0.1. What kind of steps should i do? I turn off xpenology, replace flashdrive from jun`s loader to redpill and power on. Result is: i see nothing in synology assistant. I thought i will see my NAS with status "migrate" or something. any suggestion? if you have a DHCP in your network try to see ip assigned, if you know mac-address of your baremetal, once targeted you can poi browser to this ip Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1054 Posted September 7, 2021 2 minutes ago, Aigor said: migrate from 6.2.3 to 7.0.1 i seams like this was to big step. I made now redpill for 6.2.4 and upgrade goes well. Now another step: 6.2.4 -> 7.0... Link to comment Share on other sites More sharing options...
nemesis122 Posted September 7, 2021 Share #1055 Posted September 7, 2021 Has anyone the loader for Bromolow 3615 and can upload for me ? thank you Link to comment Share on other sites More sharing options...
sirdrug Posted September 7, 2021 Share #1056 Posted September 7, 2021 In /var/log/messages Sep 7 09:13:13 updater: updater.c:7045 ==== Start flash update ==== Sep 7 09:13:13 updater: updater.c:7049 This is X86 platform Sep 7 09:13:13 updater: boot/boot_lock.c(228): failed to mount boot device /dev/synoboot2 /tmp/bootmnt (errno:2) Sep 7 09:13:13 updater: updater.c:6510 Failed to mount boot partition Sep 7 09:13:13 updater: updater.c:3134 No need to reset reason for v.42214 Sep 7 09:13:13 updater: updater.c:7652 Failed to accomplish the update! (errno = 21) Sep 7 09:13:13 install.cgi: ninstaller.c:1546 Executing [/tmpData/upd@te/updater -v /tmpData > /dev/null 2>&1] error[21] Sep 7 09:13:15 install.cgi: ninstaller.c:123 Mount partion /dev/md0 /tmpRoot Sep 7 09:13:15 install.cgi: ninstaller.c:1515 Moving updater for configuration upgrade...cmd=[/bin/mv -f /tmpData/upd@te/updater /tmpRoot/.updater > /dev/null 2>&1] Sep 7 09:13:15 install.cgi: ninstaller.c:152 umount partition /tmpRoot Sep 7 09:13:15 install.cgi: ErrFHOSTCleanPatchDirFile: After updating /tmpData/upd@te...cmd=[/bin/rm -rf /tmpData/upd@te > /dev/null 2>&1] Sep 7 09:13:15 install.cgi: ErrFHOSTCleanPatchDirFile: Remove /tmpData/upd@te.pat... Sep 7 09:13:15 install.cgi: ErrFHOSTDoUpgrade(1794): child process failed, retv=-21 Sep 7 09:13:15 install.cgi: ninstaller.c:1811(ErrFHOSTDoUpgrade) err=[-1] Sep 7 09:13:15 install.cgi: ninstaller.c:1815(ErrFHOSTDoUpgrade) retv=[-21] Sep 7 09:13:15 install.cgi: install.c:409 Upgrade by the manual patch fail. Sep 7 09:13:15 install.cgi: install.c:678 Upgrade by the uploaded patch /tmpData/@autoupdate/upload.pat fail. any ideas? Link to comment Share on other sites More sharing options...
WiteWulf Posted September 7, 2021 Share #1057 Posted September 7, 2021 I had a couple more odd reboots of my system this morning. They always seem to occur shortly after a reboot. I'd restarted the system after updating firmware on the iLO card in my system, and the server rebooted almost immediately after it had booted into DSM (I think it managed about 3 minutes uptime), then rebooted again shortly afterwards. Looking in /var/log/messages for entries just before it reboots each time there's nothing that stands out, other than that it's typically doing stuff you'd expect after the system had just rebooted: starting docker containers and registering certificates for a couple of webhosts I have on the server Link to comment Share on other sites More sharing options...
WiteWulf Posted September 7, 2021 Share #1058 Posted September 7, 2021 (edited) Question: I have an HP NC360T PCIe NIC card in my system. I'm only using one interface, so have only declared one of them in my user_config.json. Is this a problem? I notice in Control Panel in DSM that two interfaces are detected, and both have the same MAC address (the one I declared for the interface that I'm actually using). Likewise, running 'ifconfig' from the cli reports two interfaces with the same MAC address. I know that an OSI 7-layer network stack shouldn't have an issue with multiple interfaces on a system having the same MAC address (it's standard on Sun machines, for example), but will DSM complain about this? Next time I rebuild the boot stick I'll be sure to declare both interfaces, but am just curious for now. Edited September 7, 2021 by WiteWulf Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1059 Posted September 7, 2021 50 minutes ago, shibby said: Now another step: 6.2.4 -> 7.0 without luck. Any suggestion how to upgrade 6.2.4 to 7.0? Link to comment Share on other sites More sharing options...
WiteWulf Posted September 7, 2021 Share #1060 Posted September 7, 2021 1 minute ago, shibby said: without luck. Any suggestion how to upgrade 6.2.4 to 7.0? You haven't stated what procedure you're following, how it's failing or what hardware you have. If you want help you need to give people a lot more information. Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1061 Posted September 7, 2021 firmware: DS918+ 6.2.4, redpill-6.2.4. Hardware: Lenovo M93p (i5 4gen, one SSD drive) - this is only for test. first try: turn off nas, replace flashdrive with redpill-7.0, turn on nas. Result: nas is not available, no ping, empty list in synology assistant second try: from DSM 6.2.4 i run manually update to 7.0-41890. NAS has been restarted (still runned on redpil-6.2.4) goes to recovery state. Tried to continue recovery, NAS restarted but still was in recovery mode. So i replace loader to redpill-7.0 and run recovery once again but after few second i back to recovery main page. I`m testing and trying to figure out a working procedure to upgrade Xpenology from 6.2.3 to 7.0 before i will do this on my prime NAS. 1 Link to comment Share on other sites More sharing options...
Franks4fingers Posted September 7, 2021 Share #1062 Posted September 7, 2021 My spare baremetal PC (Optiplex 9020 SFF) starts the boot from USB and gets stuck at the Booting Kernel message. I can then find the device from my laptop by either using find.synology.com or the IP address. The issue I have from there is that I get the error message that others appear to have had. We've detected an error on the hard drives (3,4,5,6) and the SATA ports have also been disabled. I have tried this using both UEFI and Legacy boot from within the BIOS and get the same issue. Does anyone have any tips to get past this point? Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1063 Posted September 7, 2021 2 minutes ago, Franks4fingers said: We've detected an error on the hard drives (3,4,5,6) and the SATA ports have also been disabled. had the same. Solution for me was added DiskIdxMap=00 SataPortMap=1 SasIdxMap=0 to boot/grup/grub.cfg file (line 45: linux /zImage ...) 1 Link to comment Share on other sites More sharing options...
TSo3 Posted September 7, 2021 Share #1064 Posted September 7, 2021 (edited) On 9/4/2021 at 1:24 PM, tocinillo2 said: Compiled 7.0.1 with last BSP patch and works perfect https://drive.google.com/file/d/1CqqhO-TBdwOff0dH54iP-XPdrhzgvtNR/view?usp=sharing - Add UEFI support. - Deleted twice EFI folder. - Fixed SynoBoot_EFI place. - Compiled with last BSP Patch for 7.0.1. - Insmod efi_gop into EFI. - Tested with Baremetal and works fine (Astock 3455-ITX). - After installation (the reboot process can take 15-20 minutes) you have to install File Station manually: https://www.synology.com/en-us/support/download/DS918+#system (select DSM 7.0), find and download File Station SPK and install it in Package Center. I successfully upgraded my elitedesk 800 G2 (i7-6700) from 6.2.3 to 7.0.1 Just added DiskIdxMap=00 SataPortMap=4 SasIdxMap=0 to config! Everything works fine and super fast, also face recognition on photos. File Station was already installed (maybe because I did an upgrade) Thank you very much! Edited September 7, 2021 by TSo3 1 Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1065 Posted September 7, 2021 1 minute ago, TSo3 said: I successfully upgraded my elitedesk 800 G2 (i7-6700) from 6.2.3 to 7.0.1 can you discribe steps which yuo made? Link to comment Share on other sites More sharing options...
Franks4fingers Posted September 7, 2021 Share #1066 Posted September 7, 2021 5 minutes ago, shibby said: had the same. Solution for me was added DiskIdxMap=00 SataPortMap=1 SasIdxMap=0 to boot/grup/grub.cfg file (line 45: linux /zImage ...) 5 minutes ago, TSo3 said: I successfully upgraded my elitedesk 800 G2 (i7-6700) from 6.2.3 to 7.0.1 Just added DiskIdxMap=00 SataPortMap=4 SasIdxMap=0 to config! Thank you very much! That line in my grub.cfg file is as follows: linux /zImage netif_num=1 earlycon=uart8250,io,0x3f8,115200n8 syno_hdd_powerup_seq=1 syno_hdd_detect=0 elevator=elevator root=/dev/md0 loglevel=15 log_buf_len=32M mac1=123456789012 vid=0x0781 pid=0x5572 console=ttyS0,115200n8 sn=xxxxxxxxxxxxx earlyprintk syno_port_thaw=1 HddHotplug=0 withefi syno_hw_version=DS918+ vender_format_version=2 Did you add the DiskIdxMap= SataPortMap= SasIdxMap= values to the end of that line? Also, how did you derive what the SataPortMap value needed to be? Cheers for the help. Link to comment Share on other sites More sharing options...
TSo3 Posted September 7, 2021 Share #1067 Posted September 7, 2021 Just now, shibby said: can you discribe steps which yuo made? I did exactly what the old guide says. Mount the img with OSFMount and added VIN, PID, SN, MAC and DiskIdxMap=00 SataPortMap=4 SasIdxMap=0 on grub. After that i just put the usb on PC and i started the upgrade Link to comment Share on other sites More sharing options...
TSo3 Posted September 7, 2021 Share #1068 Posted September 7, 2021 3 minutes ago, Franks4fingers said: That line in my grub.cfg file is as follows: linux /zImage netif_num=1 earlycon=uart8250,io,0x3f8,115200n8 syno_hdd_powerup_seq=1 syno_hdd_detect=0 elevator=elevator root=/dev/md0 loglevel=15 log_buf_len=32M mac1=123456789012 vid=0x0781 pid=0x5572 console=ttyS0,115200n8 sn=xxxxxxxxxxxxx earlyprintk syno_port_thaw=1 HddHotplug=0 withefi syno_hw_version=DS918+ vender_format_version=2 Did you add the DiskIdxMap= SataPortMap= SasIdxMap= values to the end of that line? Also, how did you derive what the SataPortMap value needed to be? Cheers for the help. linux /zImage netif_num=1 earlycon=uart8250,io,0x3f8,115200n8 syno_hdd_powerup_seq=1 syno_hdd_detect=0 elevator=elevator root=/dev/md0 loglevel=15 log_buf_len=32M mac1=xxxxxxxxxxx vid=0xxxxx pid=0xxxxx console=ttyS0,115200n8 DiskIdxMap=00 SataPortMap=4 SasIdxMap=0 sn=xxxxxxxxxxx earlyprintk syno_port_thaw=1 HddHotplug=0 withefi syno_hw_version=DS918+ vender_format_version=2 That is my config. I copy SataPortMap=4 from my previous (6.2.3) config. As for DiskIdxMap=00 SasIdxMap=0 I set them to 0 just for check. So i dont know what the SataPortMap DiskIdxMap SasIdxMap value needed to be. I suppose i am lucky 2 Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1069 Posted September 7, 2021 4 minutes ago, Franks4fingers said: Did you add the DiskIdxMap= SataPortMap= SasIdxMap= values to the end of that line? to be honest i put those values between "HddHotplug=0 withefi" but this propably is not important, it may be in the middle, it may be at the end 6 minutes ago, Franks4fingers said: Also, how did you derive what the SataPortMap value needed to be? testing, testing, testing. I tried few options and this will work for me. Just try. If it will not work for you, then change SataPortMap value. 2 Link to comment Share on other sites More sharing options...
titoum Posted September 7, 2021 Share #1070 Posted September 7, 2021 all good, i have rebuild my key with parameters set correctly and all booted super duper. for those going fresh don't forget to setup your gouvernor to powersaver again 1 1 Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1071 Posted September 7, 2021 another try and another fail. fresh/clean instalation of DS918+ 6.2.3. Swaped usb drive with redpill-7.0.1 and power on PC. Result: NAS is not available, no ping, not found by assistant. The strange is that i replace HDD to the formated/clean then NAS has been available in network (found by assistant) and ready to install fresh DSM. i tested redpill compiled by myself and also shared by @tocinillo2. Result is the same. No have idea what else i can do. Best Regards. Link to comment Share on other sites More sharing options...
nemesis122 Posted September 7, 2021 Share #1072 Posted September 7, 2021 Maybe its releated to this and you need 3615 Bromolow Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1073 Posted September 7, 2021 Just now, nemesis122 said: Maybe its releated to this and you need 3615 Bromolow i have 4-gen CPU (Haswell). I can install DS918+ 6.2.3 (jun). I can install DS918+ 7.0.1 on fresh HDD using redpill. I can even upgrade from 6.2.3 (jun) to 6.2.4 (redpill) using DS918+ image. But i can`t upgrade from 6.2.3/6.2.4 to 7.x 😕 Link to comment Share on other sites More sharing options...
shibby Posted September 7, 2021 Share #1074 Posted September 7, 2021 but ok, i compile bromolow-7.0.1-42214. Now my NAS has been found by Synology Assistant as "migratable" 🤔 this is incomprehensible for me 1 Link to comment Share on other sites More sharing options...
D.S Posted September 7, 2021 Share #1075 Posted September 7, 2021 20 hours ago, pocopico said: It quite big .. i dont know if it will fit into uncompressed rd.gz and I dont know if you compress with gzip if it works. AQC107.7z 1.28 MB · 5 downloads Thanks! Tried but it doesn't work. Link to comment Share on other sites More sharing options...
Recommended Posts