Recommended Posts

Just seen that DSM 5.2-5592 Update 3 has been released by Synology.

 

Release Notes:

 

Version : 5.2-5592 Update 3

 

(2015/08/20)

Fixed Issues

 

Optimized fan settings for DS715 and DS215+.

Enhanced compatibility with hard drives.

Improved the compatibility with UPS devices.

Fixed an issue where the NTP (Network Time Protocol) service became temporarily unavailable after manual calibration.

 

Anyone know if we can just update to this with the latest version of xpenoboot?

Share this post


Link to post
Share on other sites
all disk will be unmounted and can NOT be mount

 

 

after second reboot everything seems to be OK (verified on 3 xpenos: N54l, ESXi and QNAP TS-469PRO)

Share this post


Link to post
Share on other sites

Have installed update 3 today virtualized on kvm and had no disk after the restart from the Update.

After next reboot everything is working fine again.

 

just reboot at minimum twice and everything should work as expected :ugeek:

 

 

edit: experienced off behavior:

 

update 3 disabled my rsync. i had to reenable it.

but again aft er that it seems like it is fully functioning

Share this post


Link to post
Share on other sites

Although I haven't had a chance to do any testing on Update 3 (will be migrating my test & live servers tonight), I have briefly spoken with Vortex who has said that the unmounted volumes is normal on the first reboot. As for certain services needing to be manually re-enabled, I would guess that is related to the unmounted volumes (ie. Web Station disables itself because it cant find the 'web' folder; rsync disables itself because there are no volumes to sync).

Share this post


Link to post
Share on other sites
all disk will be unmounted and can NOT be mount

 

 

after second reboot everything seems to be OK (verified on 3 xpenos: N54l, ESXi and QNAP TS-469PRO)

 

 

 

all disk will be unmounted and can NOT be mount

 

restart one more time and it will re-mount all drives

 

 

It work! after restart twice, everything come back!!

Share this post


Link to post
Share on other sites

 

 

after second reboot everything seems to be OK (verified on 3 xpenos: N54l, ESXi and QNAP TS-469PRO)

 

 

 

 

restart one more time and it will re-mount all drives

 

 

It work! after restart twice, everything come back!!

Share this post


Link to post
Share on other sites

Yes, I can confirm that update 3 works. Just reboot into upgrade/migrate mode, run the updater from control panel. I let the system download it directly and update it and reboot the first time. Confirmed, first reboot, volumes are missing. Reboot again and volumes come back. Per YoungHo, gotta re-enable user home service as well as re-run the media indexing function. So far, these services need to be manually restarted, even after the 2nd reboot:

 

1. User Home Service

2. Media Indexing

3. Log Center

4. Backup Service

 

I have a bare-metal install with no apps other than default so I'm not sure what else might be effected. Can anyone confirm any other system services/apps that needed a manual stop/start to get back going after update 3 installation? Add your comments here!

Share this post


Link to post
Share on other sites

hi guys,

 

i rebooted several times with no luck, my update went automatically yesterday en since then cant do anything with nas. because no hdd is found and all services is down. if i log and try to change things like restoring settings or pointing hdd get a error ( The operation failed. plz log in to dsm and retry )

 

i reboot more then 10 times already with upgrade funtion and also debug mode stil the same.

 

also i dont see ip adres in system health wiget or uptime.

 

System internal service [synobackupd, hotplugd, synostoraged] failed to start. Please contact Synology support for assistance.

 

anyone any idea how to set all back to normal

 

regards

Share this post


Link to post
Share on other sites

No problems everything working fine on bare metal after second reboot, And rebooting several times just to be sure.

 

 

( I Did not choose Install/Upgrade )

 

I simply downloaded and installed through control panel.

 

 

Dell Optiplex 760

Share this post


Link to post
Share on other sites

I did not choose Install/Upgrade, too ! - after second reboot Update 3 works fine on G7 with vmware !

 

BUT:

Surveillance Station (7.1) with FOSCAM 9805W and other disconnects/connect every 30 sec. - the camera interface of the Foscam looks nice all time.

Its not possible to use it !

 

Same on the 213j works fine !?

Share this post


Link to post
Share on other sites

Upgraded. Volume dismounted after 1st start after upgrade. 2nd restart fixed volume.

Found some packages in stopped mode and started it.

No issues in general.

Running a VM under Hyper-V

Share this post


Link to post
Share on other sites

I am new to XPEnology. It been running great. However I didn't realize auto update was on and now I get the following with update 3:

 

System internal service [synobackupd, hotplugd, synostoraged] failed to start. Please contact Synology support for assistance.

 

Any ideas of what to try? Really hope I didn't loose everything.

 

any help is appreciated

Share this post


Link to post
Share on other sites

Update 3 downloaded directly and installed without using install\upgrade mode.

Successfull on G7 with Vmware ESXI 6.0

All Volumes there after 2 restarts.

 

Perfect

Share this post


Link to post
Share on other sites

Successfully applied update 3 to my HP N54L DSM 5.2 5299 Update 2 instance today.

 

Had to reboot twice and then reapply my Media Server and Video Station folder settings + reindex.

 

All good now.

Share this post


Link to post
Share on other sites

Update 3 downloaded directly and installed without using install\upgrade mode.

Successfull on Bare metal

Needed to reboot twice.

 

Perfect

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.