hiyo Posted December 15, 2020 Share #1 Posted December 15, 2020 Hey Guys, Wealth of information here. Been running fine with my setup until update 3. I am using hardware passthrough with my LSI card on ESXI 6.7. My setup no longer can be seen by Synology assistant and i can no longer ping my ip either. If i remove the LSI controller everything works again. I am hoping there is a simple fix for this. Anyone experienced this and can shed some light? I have noticed the 918 image + 1.04b loader works fine wth my setup, which leads me to my last question. Should I stick with 3617xs image to take better advantage of the 16gb+ memory, or does it matter if I moved over to the 918+ image? would I loose any performance etc. Thanks ! Loader version and model: Jun's Loader v1.03b DS3617XS Using custom extra.lzma: No Installation type: VM - ESXi 6.7 with FixSynoboot.sh installed) (16gb memory) AMD RYZEN 5 3400g Asrock b450M Pro 4 / LSI SAS9207-8i passthrough / Mellanox Connectx-3 En Mcx311a-xcat 10 GbE card Quote Link to comment Share on other sites More sharing options...
mic-cosmos Posted December 24, 2020 Share #2 Posted December 24, 2020 I have the same issue. Here's how I fixed my VM back to update 2 if anyone's curious in response to a DM: I did revert back to update 2 but it was a difficult process. The server was stuck in an endless recovery loop where I would be able to access the recovery menu after using a fresh synoboot.img but this was followed by the server being rebooted and then not registering an IP address. I managed to get to the DSM by choosing the "baremetal" option instead of the virtual machine option but only 2/4 HDDs on the HBA passthrough would register and my HDD RAID array showed up as "crashed". I eventually managed to reinstall the update 2 DSM by disconnecting the HBA passthrough and the installing a fresh DSM on a virtual HDD. I then reconnected the HBA passthrough. After I booted into the DSM using the virtual HDD, I got the message that the DSM installs on my HBA passthrough HDDs were no good and was asked if I wanted to reinstall the DSM (using the one from the virtual HDD).; I chose yes. I then removed the virtual HDD and was then able to boot to DSM using my HBA passthroughs and update back up to update 2 after that. Quote Link to comment Share on other sites More sharing options...
dynaguy Posted December 30, 2020 Share #3 Posted December 30, 2020 (edited) I have the exact problem and I endup with rebuild with version 6.2.2-24922 now. Loader version and model: Jun's Loader v1.03b DS3617XS Using custom extra.lzma: No Installation type: VM - ESXi 6.7 with FixSynoboot.sh installed) (6gb memory) Virtual NIC: E1000e Passthrough: Dell SAS 6Gbps HBA Edited December 30, 2020 by dynaguy Quote Link to comment Share on other sites More sharing options...
vikikang Posted January 7, 2021 Share #4 Posted January 7, 2021 Wish I Could saw this earlier. Had to recreate vm to roll back to update2 Quote Link to comment Share on other sites More sharing options...
vikikang Posted January 21, 2021 Share #5 Posted January 21, 2021 Hey, somebody still here? Is there any solution now? Quote Link to comment Share on other sites More sharing options...
id001 Posted January 25, 2021 Share #6 Posted January 25, 2021 Same here. Attached the serial.out file Looks like it is a problem with the mpt2sas driver Is it helpful to someone? serial.out Quote Link to comment Share on other sites More sharing options...
vikikang Posted January 27, 2021 Share #7 Posted January 27, 2021 I have tried driver extnsion with no luck. Quote Link to comment Share on other sites More sharing options...
bateau Posted January 31, 2021 Share #8 Posted January 31, 2021 +1 to I wish I had seen this thread. 6.2.3-Update 3 fails to connect to network on ESXi with LSI controller in pass-through. Rolling back to Update 2. Quote Link to comment Share on other sites More sharing options...
Orphée Posted January 31, 2021 Share #9 Posted January 31, 2021 Hello, For me it worked with DS3615xs : Quote Link to comment Share on other sites More sharing options...
vikikang Posted February 1, 2021 Share #10 Posted February 1, 2021 5 hours ago, Orphée said: Hello, For me it worked with DS3615xs : It seems this problem is specific with 3617xs model and Esxi combination Quote Link to comment Share on other sites More sharing options...
Hokey33 Posted June 14, 2021 Share #11 Posted June 14, 2021 (edited) Can someone confirm that 6.2.3-Update 3 could work with Dell H200 IT passthrough on DS3615xs? Edited June 14, 2021 by Hokey33 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.