DoganReis 0 Posted January 5 Share Posted January 5 - Outcome of the installation/update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - Intel Core i3-9100F - MSI H310M PRO-VDH PLUS LGA 1151 - 16GB DDDR4 - 2x 2TB HDD - Additional Comment: Reboot required Quote Link to post Share on other sites
muld626 1 Posted January 6 Share Posted January 6 - Outcome of the installation/update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun v1.04b - DS918+ - Using custom extra.lzma: Yes I-88 13.3 - Installation type: BAREMETAL - Intel Core i3-8300 - Supermicro X11SCH-F - 16GB - 8 x 4TB Red WD AFRX - 10Gb NIC (asus C100C / Aquantia C107) & 1Gb NIC (Intel-i210) - Additional Comment: Plex HW decoding OK / Reboot required Quote Link to post Share on other sites
rafailof 0 Posted January 6 Share Posted January 6 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: JUN'S LOADER v1.03b / 3615xs - Using custom extra.lzma: No - Installation type: BAREMETAL / Asus P5B Deluxe / RAM OCZ Platinum 4GB (2 x 2GB) OCZ2P10664GK / CPU INTEL XEON E5440 QUAD CORE - Additional comments: The update has been done automatically. No manual reboot from my side. Using an SSD cache, no problem from the update Edited January 6 by rafailof Quote Link to post Share on other sites
ColinO53 1 Posted January 7 Share Posted January 7 On 12/23/2020 at 4:42 AM, siang said: - Outcome of the update: Unsuccessful - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: JUN'S LOADER v1.03b - DS3617XS - Using custom extra.lzma: No - Installation type: VM - ESXI 6.5 (FixSynoboot.sh), Intel i350-T4 Quad Port (Passthrough), LSI 9211-8i IT mode (Passthrough) with 8x3TB. - Additional comments: VM with LSI HBA card passthrough should avoid update 3. Not detected (No IP) with LSI 9211-8i HBA card after update. Suspect the DSM not recognise the HBA therefore not booting DSM properly to obtain network IP. Replaced fresh copy of DS3615xs synoboot VM to boot and migrate, then replace fresh copy of DS3617xs synoboot VM and finally migrate back to DS3617xs DSM 6.2.3, follow with manually updating to 6.2.3-25426 Update 2. Stay with 6.2.3-25426 Update 2 until known solution. I had a similar experience the only difference between my setup and Siang's is I'm using a Dell R610 with a PERC H200 HBA and no IT mode as it recognized the drives on first boot. The card is configured as a passthrough to the VM and I'm running Proxmox 6.3-3 as my hypervisor. Regardless of the differences I had the eact same problem. Once I removed the H200 passthrough from the VM. I was able to see the box again. I couldn't roll it back so i had to tear down the VM and start over. As Siang said DO NOT UPGRADE to UPDATE 3 for now! 1 Quote Link to post Share on other sites
FRANCESCHIP 0 Posted January 8 Share Posted January 8 (edited) - Outcome of the update: SUCCESSFULL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun's Loader v1.03b DS3615XS - Using custom extra.lzma: No - Installation type: BAREMETAL - Intel NIC (HP NC360T) - HP ProLiant MicroServer N54L - Additional comment: Installation from DSM update menu. Reboot required Edited January 8 by FRANCESCHIP Quote Link to post Share on other sites
mortisboy 2 Posted January 8 Share Posted January 8 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: No - Installation type: BAREMETAL - ASUS H87I Plus - i7 4770K - All onboard working fine with 5x4TB@RAID5 and SSD cache - Additional comment: Upgraded via DSM function - Reboot Required Quote Link to post Share on other sites
gfacek2 0 Posted January 8 Share Posted January 8 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 Update 4 - Loader version and model: JUN'S LOADER v1.04b - 918+ - Using custom extra.lzma: No - Installation type: BAREMETAL - ASRock J5040-ITX - Additional comments: 2x Reboot required Quote Link to post Share on other sites
rickym 4 Posted January 12 Share Posted January 12 -Outcome of the installation: SUCCESSFUL -DSM version prior update: DSM 6.2.3-25426 Update 2 -Loader version and model: JUN'S LOADER v1.04b DS918xs -Using custom extra.lzma: No -Installation type: BAREMETAL - Asus H110i Plus ITX motherboard -Intel 82574L Nic as internal nic didn't work. Quote Link to post Share on other sites
insolegeek 0 Posted January 12 Share Posted January 12 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: No - Installation type: Custom - MSI B250I PRO - Pentium G4560 - Additional comment: Upgraded via DSM function - Reboot Required Edited January 12 by insolegeek Quote Link to post Share on other sites
meninred 0 Posted January 12 Share Posted January 12 (edited) - Outcome of the update: SUCCESSFULL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun's Loader v1.03b DS3615XS - Using custom extra.lzma: No - Installation type: BAREMETAL - HP Proliant ML110 G6 - Additional comment: Installation from DSM update menu. Reboot required - FixSynoboot.sh applied before update - D-Link DGE-530T as 2nd internal nic Edited January 12 by meninred Quote Link to post Share on other sites
vencafm 0 Posted January 13 Share Posted January 13 - Outcome of the update: SUCCESSFULL - DSM version prior update: DSM 6.2.2-24922 update 6 and clean HW - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: Yes Ig-88 v13.3 - Installation type: BAREMETAL Fujitsu Esprimo P720 E90+ MT, Intel Core i3 4160 3.6 GHz, 8 GB RAM - Additional comments: The installation was several times repeated due to failing reboot after installation. The problem was with an old USB disk (512MB), the replacement with newer 4GB usb fixed the problem. Custom Extra.lzma installed to get proper drivers for intel VGA to get HW transcoding in PLEX Quote Link to post Share on other sites
kitkat 0 Posted January 16 Share Posted January 16 (edited) - Outcome of the update: SUCCESSFULL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: No - Installation type: BAREMETAL ASRock J4125-ITX (Celeron J4125) 8GB DDR4 / 3*1TB IronWolf - Additional comments: FixSynoboot.sh mandatory , Reboot Edited January 16 by kitkat Quote Link to post Share on other sites
mykia 0 Posted January 17 Share Posted January 17 - Outcome of the migration: SUCCESSFULL - DSM version prior update: DSM 5.2-5967-update 9 - Loader version and model: Jun's Loader v1.03b DS3615XS - Using custom extra.lzma: No - Installation type: BAREMETAL GigaByte Q67M-Dd2H-B3 - cpu i3-2120 -8GB DDR3 1600 (Hyperx )/2*1TB WDRED3.5 +1TB 2.5 - Additional comments: In order to perform the migration, I deleted, from each disk, the first partition with a Gparted live Quote Link to post Share on other sites
Hostilian 14 Posted January 17 Share Posted January 17 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3 25426 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: YES - Installation type: BAREMETAL - ASROCK J3455-itx. Intel NIC in there too and multiple drives. - Additional comments: Worked first time. Automatic, full reboot to login promot. No issues and no need to remove my custom extra.lzma (used prior to previous upgrade). Quote Link to post Share on other sites
harryw 0 Posted January 21 Share Posted January 21 - Outcome of the update: UNSUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: Jun's Loader v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - HP Microserver Gen8 8Gb RAM (4Gb ECC and 4Gb non-ECC) - Additional comments: Unable to apply updates. See attached screen shots of the process and failure. Quote Link to post Share on other sites
harryw 0 Posted January 22 Share Posted January 22 11 hours ago, harryw said: - Outcome of the update: UNSUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: Jun's Loader v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - HP Microserver Gen8 8Gb RAM (4Gb ECC and 4Gb non-ECC) - Additional comments: Unable to apply updates. See attached screen shots of the process and failure. After applying the suggested script FixSynoboot.sh, rebooting and then trying the Update again all is good. Thank you 'flyride' for the suggestion. I had a look at it before but wasn't sure if it was relevant to my bare metal Gen8. Quote Link to post Share on other sites
SebeekS 0 Posted January 23 Share Posted January 23 (edited) - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3 25426 Update 2 - Loader version and model: Jun's Loader v1.04b DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - ASUS J1900I-C (2x4GB RAM + PCIe Marvell 9125 2x SATA) - Additional comments: Worked fine, rebooted to login screen. Edited January 23 by SebeekS Quote Link to post Share on other sites
bateau 5 Posted January 23 Share Posted January 23 - Outcome of the installation/update: UNSUCCESSFUL - DSM version prior update: DSM 6.2.3 25426 Update 2 - Loader version and model: JUN'S LOADER v1.03b - DS3617xs - Using custom extra.lzma: NO - Installation type: VM - ESXi 6.7 - Additional comments: Doesn't show up on the network. ESXi doesn't show IP address requested. @flyride, may I trouble you for some assistance? As far as I recall FixSinoboot.sh was applied before. Quote Link to post Share on other sites
trevvv 0 Posted January 24 Share Posted January 24 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 - Loader version and model: Jun's Loader v1.03b DS3617xs - Using custom extra.lzma: No - Installation type: VM - ESXi 6.7 U3 (with FixSynoboot.sh installed) Test system - Additional comment: FixSynoboot.sh. Manual Update. Reboot Required. Quote Link to post Share on other sites
stone 0 Posted January 26 Share Posted January 26 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6..1.6 15266 - Loader version and model: Jun's Loader v1.03b DS3615xs - Using custom extra.lzma: No - Installation type: asus p8p67-lw, i5 2500k, manual update via control panel sitenote:I am completely new and couldnt find a tutorial how to upgrade - not sure if i did it right but thats how it worked for me: -downloaded latest .pat -created new usb stick with serial from OLD stick but with new loader -control panel -> manual choose downloaded pat file -> confirm -> update loads and system reboots but did not come back - plug in new usb stick and "hard reboot" -> still not reachable but found via syn assist -option to recover available -> started recover -> after further reboot all back to normal (except re-installing/repairing some apps) Quote Link to post Share on other sites
NeoID 6 Posted January 27 Share Posted January 27 - Outcome of the installation/update: UNSUCCESSFUL - DSM version prior update: DSM 6.2.3 25426 Update 2 - Loader version and model: JUN'S LOADER v1.03b - DS3617xs - Using custom extra.lzma: NO - Installation type: VM - ESXi 6.7 - Additional comments: Same as all other people who use ESXi and a PCI/LSI card in passthrough mode. After the upgrade the NAS cannot be found on the network anymore. The only way I got access again was to temporarily switch to the DS3615xs loader and reinstall DSM and then migrate back to DS3617xs again. If you use a PCI card in passthrough DO NOT UPDATE to this version. Quote Link to post Share on other sites
Krisje 1 Posted January 31 Share Posted January 31 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.2-24922 update 4 - Loader version and model: JUN'S LOADER v1.04b DS 918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL – Jetway NF9M Celeron N2930, NIC RTL 8111G - Additional comments: Real3x mod removed Quote Link to post Share on other sites
bbkw 0 Posted February 3 Share Posted February 3 - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3 25426 Update 2 - Loader version and model: JUN'S LOADER v1.04b DS 918+ - Using custom extra.lzma: NO - Installation type: J1900, 4GB - Additional comments: fixsynoboot.sh. Auto update. Reboot Quote Link to post Share on other sites
Dundermiflin 0 Posted February 3 Share Posted February 3 - Outcome of the update: SUCCESSFULL - DSM version prior update: DSM 6.2.3-25426 Update 2 - Loader version and model: Jun's Loader v1.03b DS3615XS - Using custom extra.lzma: No - Installation type: BAREMETAL - HP Microserver Gen8 - Additional comment: Installation from DSM update menu. Reboot required - FixSynoboot.sh applied before update Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.