malibu70 Posted September 23, 2020 Share #1 Posted September 23, 2020 Good eveninng during 2 weeks i try to install a xpenology in new pc, configuration Amd Athlon 3000g Gigabyte B450M s2H Intel EXPI9402PTBLK net card any loader 6.x can see from network with find.synology.com or synology assitant i try 5.2 loaders and synology assistant and find.synology can see and start to install but at 40% stop during upload files (i try many diferents) in the begining i try with the netcard from mother board but is a realtek and i read can be some problems so i buy a Intel EXPI9402PTBLK that i read can work perfect with xpenolgy 6.x but too have the same problem. anybody can help me? Thanks in advance Quote Link to comment Share on other sites More sharing options...
IG-88 Posted September 23, 2020 Share #2 Posted September 23, 2020 check if the vid/pid of the usb flash drive you use is in the grub.cfg https://xpenology.com/forum/topic/7973-tutorial-installmigrate-dsm-52-to-61x-juns-loader/ Quote Link to comment Share on other sites More sharing options...
malibu70 Posted September 23, 2020 Author Share #3 Posted September 23, 2020 Thank you so much for your answer master, i did, even i change usb drives with 3 kinds diferent example: Volume: None Controller: SanDisk Possible Memory Chip(s): Not available VID: 0781 PID: 5583 Manufacturer: SanDisk grub: set vid=0x0781 set pid=0x5583 set sn=1330ODN0259xx set mac1=0015173E45xx i follow all the post but i cant find where is my mistake, i start to think about the image attached is when i start with 5.2 loader, with 6.x in anyway assistant cand find with the realtek from board or with intel Quote Link to comment Share on other sites More sharing options...
IG-88 Posted September 23, 2020 Share #4 Posted September 23, 2020 31 minutes ago, malibu70 said: the image attached is when i start with 5.2 loader, with 6.x in anyway assistant cand find with the realtek from board or with intel i was talking about 6.2 loaders like 1.03b and 1.04b, haven't touched a 5.2 loader for years 1.03b needs csm/legacy mode in bios to boot) and also the legacy usb device needs to be selected and might only show up after restarting once with csm active) 1.04b should boot in default uefi mode, not sure if the realtek chip (8118, is just a fancy 8111 aka 8168) will work ootb with juns driver pack but should at least work with this one https://xpenology.com/forum/topic/28321-driver-extension-jun-103b104b-for-dsm623-for-918-3615xs-3617xs/ Quote Link to comment Share on other sites More sharing options...
malibu70 Posted September 27, 2020 Author Share #5 Posted September 27, 2020 Thanks a lot for your answer, finally i have runnig Quote Link to comment Share on other sites More sharing options...
IG-88 Posted September 27, 2020 Share #6 Posted September 27, 2020 35 minutes ago, malibu70 said: Thanks a lot for your answer, finally i have runnig any conclusion that might help other people? what loader and dsm version you ended up? used any extra.lzma for drivers? Quote Link to comment Share on other sites More sharing options...
malibu70 Posted September 27, 2020 Author Share #7 Posted September 27, 2020 i used 1.04b for 918+ with extra.lzma/extra2.lzma for loader 1.04b ds918+ DSM 6.2.3 v0.13.3 as you advice but during the week i couldnt doit, i have to wait till weekend for experiments Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.