Ermite

DSM 6.2.3-25426 Update 2

Polanskiman

Please read the READ ME topic before posting:

 

Message added by Polanskiman

Recommended Posts

image.thumb.png.8434671efef804881b0dad4adf7c6422.png

 

https://www.synology.com/en-global/releaseNote/DS3615xs
 

Spoiler

Version: 6.2.3-25426-2
(2020-07-16)


Important Note

Your Synology NAS may not notify you of this DSM update because of the following reasons. If you want to update your DSM to this version now, please click here to manually update it. Only Synology NAS with DSM 6.2.3 installed can be updated to this version.
The update is not available in your region yet. The update is expected to be available for all regions within the next few days, although the time of release in each region may vary slightly.
This update will restart your Synology NAS.


What's New

Added support for Synology Expansion Unit FX2421.


Fixed Issues

Fixed the issue where a DS920+ or DS720+ might not enter hibernation when its connected expansion unit has entered deep sleep.
Fixed the issue where drive status LED indicators on a connected expansion unit might not work properly when the expansion unit wakes up from deep sleep.
Fixed the issue where daylight saving time might not display correctly in certain time zones (e.g., Dublin, Casablanca).
Fixed the issue where mounted remote shared folders on a Synology NAS may cause volumes to operate improperly or the Synology NAS unable to shut down in certain scenarios.
Fixed the issue where the system might incorrectly prompt "drive slot disabled” notice when a DS413 or DS213+ wakes up from deep sleep.
Enhanced the performance in writing a large number of files to a Btrfs volume with RAID 1 configuration using hard disk drives (HDD).
Fixed the issue where Synology Universal Search and Synology Drive might consume excessive CPU resources when the option "Utilize unused memory as database cache to improve (search) performance" has been enabled.
Fixed the issue where domain-related services might not resume working because the update of domain data could not be complete.
Fixed security vulnerabilities (Synology-SA-20:18).
Fixed the issue where the system might incorrectly prompt IP address conflict warning if a network interface card is attached to Synology NAS and the option "Reply to ARP requests if the target IP address is a local address configured on the incoming interface" is disabled.
Fixed the issue where the status of an Ethernet port might not be detected properly when the Ethernet port is not connected to a network cable while Open vSwitch has been enabled.

 

Share this post


Link to post
Share on other sites

Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP N54L, Intel 82576 Dual RJ45 PCIe 2.0 x1, Enermax 2.5" x1, 3.5" x1 HDD Bay, PM-MSATA22GT-R (mSATA x2, SATA Gen3 x2) PCIe SATA Expansion Card

- Additional comments:  Update with DSM GUI to DSM 6.2.3-25426 Update 2 : All is work.

Share this post


Link to post
Share on other sites

Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BareMetal | ASRock B250M Pro4 | i5-6400T | Intel X520-QDA1 | 4x WD Red 3TB  & 2x 128GB Intenso NVME

- Additional comments: all fine

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.04b - DS918+ 

- Using custom extra.lzma: NO

- Installation type: VM in ESXi 6.7 - GA-X150M-PLUS / Cpu : E3-1240L v5 / Ram : 16G Ecc / Nic : RTL8111

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock C2750D4I

- Additional comments: REBOOT REQUIRED -- Manual Update

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615XS

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver  Gen7 N54L

- Additional comments: Reboot required

 

 

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615XS

- Using custom extra.lzma: NO

- Installation type: VM - ESXI 6.5

- Additional comments: Reboot required - shutdown and restart working now with 6.2.3 !!!

Share this post


Link to post
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver Gen 8 with Intel NIC

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615XS

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver  Gen7 N54L

- Additional comments: Reboot required, download bromolow file from https://archive.synology.com/download/DSM/criticalupdate/update_pack/25426-2/

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3

- Loader version and model: Jun's v1.04b - DS918+

- Using custom extra.lzma: YES (v0.11 for 6.23 by IG-88)

- Installation type: BAREMETAL - ASROCK Z370M PRO4 - i5-8600k - Giga PHY Intel® I219V

- Additional comments: reboot, HW transcode is still working in Plex and Jellyfin.

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - HP ProLiant MicroServer Gen8 (Xeon E3-1265L)

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

 Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: extra3615_v0.12_test

- Installation type: BAREMETAL - HP ProLiant MicroServer Gen8 (Xeon E3-1265L)

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

 Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: Yes - v0.13.2 by IG-88

- Installation type: BAREMETAL - Asrock N3700-ITX

- Additional comment: Updated via auto-update; Reboot required; Restart & Hardware encoding in Video Station functioning

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - HP ProLiant MicroServer N54L

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.04b DS918+

- Using custom extra.lzma: No

- Installation type: VM - ESXi (with FixSynoboot.sh installed) Test system

 

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615xs

- Using custom extra.lzma: No

- Installation type: VM - ESXi (with FixSynoboot.sh installed) Test system

 

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3617xs

- Using custom extra.lzma: No

- Installation type: VM - ESXi (with FixSynoboot.sh installed) Test system

 

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.04b DS918+

- Using custom extra.lzma: No

- Installation type: BAREMETAL J4105-ITX production system

 

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3617xs

- Using custom extra.lzma: No

- Installation type: VM - ESXi (with FixSynoboot.sh installed) production system

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.2-24922 Update 4

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: Yes + original zImage and rd.gz (extracted from Synology's 24922 PAT)

- Installation type: BAREMETAL - ASUS H81M-K (with onboard Realtek 8111G controller)

- Additional comment: Reboot required ... after that, the machine was "lost" (though booted fine, no network issue). I had to fresh remake the same USB Flash Drive, this time as "stock" (without custom extra.lzma, zImage and rd.gz). Recovered with Synology Assistant, rebooted once more and now it works like a charm (nothing modified or lost).

Share this post


Link to post
Share on other sites

- Outcome of the update:  UNSUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - HP ProLiant MicroServer GEN8

- Additional comment: File States Corrupt. Downloaded It A Few Times Do Not Know What is Going On.

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.04b DS918+

- Using custom extra.lzma: Yes - v0.13.3 by IG-88

- Installation type: Baremetal J5005-ITX production system

Share this post


Link to post
Share on other sites

Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Supermicro X8DTI-F / NIC: Intel 82576 Dual-Port Gigabit Ethernet, plus an Intel EXPI9301CTBLK PRO1000 Network Card CT PCIex / Chipset: Dual Intel E5620 Xeon / SATA Additional Controllers: Lindy 4 port SATA 3 PCIe /  Disks: 8 x 8TB WD Red, 1 x 256GB SSD

- Additional comments: After manual reboot everything recognised and working

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL
- DSM version prior update: DSM 6.2.3-25426
- Loader version and model: JUN'S LOADER v1.04b - DS918+
- Using custom extra.lzma: Yes, 0.11 for 6.2.3(HD sleep disabled)
- Installation type: BAREMETAL - Intel Pentium G4560 / 8GB / GA-B250-HD3P / LSI SAS 9211-8i (IT) / Disks : 8 x 8TB WD & 4 x 4TB WD / Pro-1000/PT PCI-e Dual Port 
- Additional comments: REBOOT REQUIRED / HW transcode works in Plex

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL
- DSM version prior update: DSM 6.2.3-25426
- Loader version and model: Jun's Loader v1.03b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - Dell Precision T1700 / Intel Xeon E3-1226 / 8GB / Disks : 4 x 2TB WD RED (WD20EFRX-68EUZN0)
- Additional comments: REBOOT REQUIRED / HW transcode works in Plex / Seems all fine

Share this post


Link to post
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL 

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

 Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.04b - DS918+ (with NVME cache)

- Using custom extra.lzma: Yes. v0.11 from IG-88

- Installation type: BAREMETAL - Supermicro X11SSZ-TLN4F + Intel Xeon E3-1245 v5

- Additional comment: NvME cache working after update, all 4 NIC available (2 x 1GBe + 2 x 10Gbe) , 16 GB RAM available, 10GBe connection  working. H/W transcoding works also using driver extension for 918+ , v0.11,

Reboot required: No

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: Yes

- Installation type: BAREMETAL - HP Microserver Gen8

- Additional comments: REBOOT REQUIRED -- Manual Update + update /etc.default/synoinfo.conf if specific (eg. more HDDs etc.)

 

The update reseted values, supposed to be restored to

- esataportcfg to 0x00000 (instead default 0xff000), 

- usbportcfg to 0x7C000 (instead default 0x300000) = 5 USB on the Gen8

- internalportcfg to 0xFFFFFF (instead of default 0xfff) = 21 Disks support in my case

Share this post


Link to post
Share on other sites

- Outcome of the update:  UNSUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - HP ProLiant MicroServer GEN8

- Additional comment: File corrupt both autodownload and manual

http://download.synology.com/download/DSM/criticalupdate/update_pack/25426-2/synology_bromolow_3615xs.pat

Share this post


Link to post
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver Gen 7 N54L

- Additional comment: Reboot required

 

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: yes - extra3615_v0.11_test

- Installation type: BAREMETAL - HP Microserver Gen 8 (Intel Xeon E3-1220L V2 with 8GB RAM and Asus NIC: ASUS XG-C100C 10Gb)

- Additional comment: Reboot required

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.