Jump to content
XPEnology Community

DSM 6.2.3-25426 Update 2


Ermite
Message added by Polanskiman

Please read the READ ME topic before posting:

 

Recommended Posts

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3  - 25426

- Loader version and model: Jun's Loader v1.03b DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asus H87i-plus with i3 CPU. Intel NIC in there too and multiple drives.

- Additional comments: Worked first time. No issues and straight back again after a reboot.

Link to comment
Share on other sites

Machine 1

- Outcome of the update: SUCCESSFUL

- DSM version prior update: n/a

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: v0.13.3

- Installation type: BAREMETAL - Asus PRIME H310I-PLUS R2.0, NIC: Realtek® RTL8111H (onboard)

- Additional comments: See below:

1. Jun's 1.04b loader is the only one that worked.  Find.synology didn't work using 1.03b for DS3615, or 1.04b w/o the additional extra.lzma.

2. First try I used I5-9600K, after replacing the i915 driver, dev/dri showed up, but hardware transcoding didn't work (just try playing any .avi).  Also, I had to replace libsynophoto-plugin-detection.so for face detection / subject in Moments to work.

3. Second try I used I5-8600K, everything worked out of the box, no need to replace i915.ko or libsynophoto-plugin-detection.so.

4. In VMM, for all VM's CPU compatibility mode must be enabled.  If not, when installing Linux, it doesn't go past the partition screen.  In Windows, if I don't enable CPU compatibility mode, strangely most applications run, but iTunes, and Irfanview would not work under Windows 7, iTunes would not work under Windows 10.  With CPU compatibility mode on, everything works.

5. WOL, shutdown, all work normally.

 

Machine 2

- Outcome of the update: SUCCESSFUL

- DSM version prior update: n/a

- Loader version and model: JUN'S LOADER v1.03b - DS3615XS

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asus P6X58D-E, NIC: Marvell 88E8056 (onboard), i7-930

- Additional comments: See below:

1. Jun's 1.03b loader is the only one that worked.  Find.synology didn't work using 1.04b.

2. In VMM, Windows 10 can only be installed when set to UEFI boot.  No need to turn on CPU compatibility mode.  Resolution must be set in the UEFI BIOS.

3. WOL, shutdown, all work normally.

4. Even though there's no dev/dri, which means it's not supposed to have hardware transcoding, it can deliver .avi videos to DS Video on my iPhone.  So some form of transcoding was working.  Because my other set up with the I5-9600k, even though dev/dri existed, .avi just won't play.

5. To summarize, everything works out of the box without additional extra.lzma, etc.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.04b - DS918+ 

- Using custom extra.lzma: Yes, v0.13.3 by IG-88

- Installation type: BAREMETAL - HP ProDesk 600 G1 SFF, CPU: Intel Core i3-4330, NIC: onboard Intel I217-LM

Link to comment
Share on other sites

  • 4 weeks later...

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.1.7

- Loader version and model: Jun's Loader v1.03b DS3615XS with virtio/9p loaded

- Using custom extra.lzma: Yes, v0.11_test by IG88

- Installation type: VM - Proxmox  6.2-11 with PCI sata controller passtrough (with 4 disks attached)

- Additional Comment: Bootloader boot as usb disk, Migration with keeping setting/data BREAKS my xpenology (maybe coz of chroot and other tiers apps) but it works back well once I did a new install migration with keeping data only (so needed to reinstall all apps)

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.1.7

- Loader version and model: JUN'S LOADER v1.03b - for DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL Gen8 Microserver G1610T

- Additional comment: Reboot required, updated number of available drives to 45. Onboard LAN working, with LSI SAS card installed.

                                               Rebooting prevents the system from loading. Need to fully shutdown and power on whenever a reboot is needed

 

 

Link to comment
Share on other sites

  • 2 weeks later...

- Outcome of the update:  SUCCESSFUL
- DSM version prior update: DSM 6.2.3-25426 Update 2
- Loader version and model: JUN'S LOADER v1.04b - DS918+
- Using custom extra.lzma: No
- Installation type: BAREMETAL - FRACTAL Design Node 804 | ASUS B150M-C D3| Celeron G9300| 16 GB RAM|+ HP NC360T
- Additional comments: Reboot required

Link to comment
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3 - 25426 update 2/ use  Fixsynoboot patch

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: VM -UNRAID - Gigabyte A970 Board With AMD 6core processor Intel NIC

- Additional comment: Reboot required

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL
- DSM version prior update: DSM 6.2.3-25426 Update 1
- Loader version and model: JUN'S LOADER v1.04b - DS918+
- Using custom extra.lzma: No
- Installation type: Proxmox VE
- Additional comments: need to modify the synology prior update or else the update always failed at file broken.

 

solution:

 

login you synology at root, and

ln /dev/sda1 /dev/synoboot1
ln /dev/sda2 /dev/synoboot2

while

sda1 is your fist volume in the 52MB synoboot image
sda2 is your second volume in the 52MB synoboot image

 

check using fdisk -l

Edited by taiziccf
Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.2-24922 Update 4

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - MSI 970 Gaming - AMD Athlon II X4 630 (AM3 CPU)

- Additional comment: Reboot Required | Manual DSM Update| NIC: HP NC-360T | On-board NIC: Disabled 

Link to comment
Share on other sites

 Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.1 - 23739

- Loader version and model: JUN'S LOADER v1.04b - DSM_DS918+_25426

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J4105-ITX | 8 Gb Ram | Sharkoon CA-M | Bequiet Pure Power 400W | WD Red 3 Tb + WD Red 3x2 Tb

- Additional comment: Reboot required

Edited by artyom
Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.2-25426

- Loader version and model: Jun's Loader v1.03b 3617XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - Intel 10400T + ASRock H410M-ITX

- Additional comment: Lagacy BIOS required. Onboard NIC is not working without an extra.lzma -> Anyway, I used an Intel E1G42ETBLK ET Dual Gigabit NIC. For fully specs read my SecondaryNAS signature

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: Clean first install

- Loader version and model: JUN'S LOADER v1.04b - DS918+ 

- Using custom extra.lzma: No

- Installation type: BAREMETAL - ASRock AM1H-ITX, Athlon 5350, RTL8111GR

- Additional comment: USB stick required to be in USB 3.0 port as well as legacy booted, or else error 13 at install.

Link to comment
Share on other sites

- Outcome of the installation: SUCCESSFUL

- DSM version prior update: Clean first install

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: Yes, loaded with @IG-88 Driver extension jun 1.03b for DS3615xs

- Installation type: BAREMETAL - ASROCK AD525PV3

- Additional comment: Reboot required

Link to comment
Share on other sites

- Outcome of the installation: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: Jun’s Loader v1.04b DS918+

- Installation type: BAREMETAL - biostar b85s3+ i3 , 32GB , GT 730 2GB

- Additional comment: Had to use FixSynoboot.sh from https://xpenology.com/forum/topic/28183-running-623-on-esxi-synoboot-is-broken-fix-available/

 

 

 

Link to comment
Share on other sites

- Outcome of the installation: SUCCESSFUL

- DSM version prior update: Clean first install

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: Yes, loaded with @IG-88 Driver extension jun 1.03b for DS3615xs

- Installation type: BAREMETAL - ASUS P9D WS

- Additional comment: Reboot required. everything is onboard, both onboard Intel NIC were detected.

 

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update:  DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.03b - DS3615XS

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock Q1900-ITX

- Additional comments: Manual update, Reboot required

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 4

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Mitac PD10BI MT Mini-ITX motherboard

- Additional comments: Reboot required

 

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426 Update 2

- Loader version and model: Jun's Loader v1.04b DS918+

- Using custom extra.lzma: v0.13.3 for 6.2.3 from IG-88

- Installation type: BAREMETAL - ASRock J5040-ITX, 8GB RAM, using onboard sata ports & nic

- Additional comment:  Got message that file was corrupt, so I added FixSynoboot.sh, then picked automatic install, rebooted.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426 UPDATE 2

- Loader version and model: JUN'S LOADER v1.04b  DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASUS H87I-PLUS - NIC: Intel I217 - SANDISK FLAIR 32GB

- Additional comments: Clean install, all fine except some improper shut downs (PC is fine not restarting) i suspect usb stick overheats.

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824-1

- Loader version and model: Jun's Loader v1.03b DS3615XS

- Using custom extra.lzma: No

- Installation type: BAREMETAL - HP ProLiant MicroServer GEN8 with Extra HP NIC 610

- Additional comment: Used the GUI to update - auto rebooted and took about 7mins :: No Drama other than Plex lost its shared folder permissions

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.3-25426

- Loader version and model: JUN'S LOADER v1.04b - DS918+ 

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Fujitsu PRIMERGY TX1310 M1, CPU: Intel Core i3-4130, NIC: onboard Intel I210

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...