Jump to content
XPEnology Community

QNAP auf eigener Hardware


fa2k

Recommended Posts

10 minutes ago, Tiras said:

Die B02:D00:F0 sollte eigentlich funktionieren. Ich bin leider verrutscht. Deine Angabe war mit B00:D28:F2 glaube ich schon richtig.

Wenn ich in TC möchte starte ich den PC neu und drücke während dem booten schon die Pfeil-Runter Taste. Damit unterbrichst du den Countdown und kannst anschließend zum a wechseln.

danke - das spart wirklich Zeit. in der Model conf steht nach der Suche

[System Network 1]
DEV_BUS = B02:D00:F0
PCI_SWITCH_PORT = -1
DEV_PORT = 0
[System Network 2]
DEV_BUS = B00:D28:F3
PCI_SWITCH_PORT = -1
DEV_PORT = 0

 

die Ports sind wie in LSPCI (normal und vtnn) - was mich wundert ist der Switch-Port (minus) -1 damit kann ich gar nichts anfangen

1 minute ago, Tiras said:

Probier mal die normale B02:D00:F0 Adresse und nur DEV_PORT = 0

mit PCI_SWITCH_PORT = 3 oder ohne?

Link to comment
Share on other sites

14 minutes ago, Tiras said:

Weist du evtl. was PCI_SWITCH_PORT oder DEV_BRIDGE_BUS bedeutet? Ich habe bisher nichts gut erklärendes gefunden.

ich wollte dich auch fragen ob es da eine Liste mit Erklärungen gibt. Beim PCI_Switch_Port denke ich es mir: In meinen lspci Listen oben siehst du bei -vtnn dass es 3 Switch Ports gibt, auf zweien davon sind Netz und die SATA Karte, da sie auf der gleichen Adresse liegen. Aber welcher Port der richtige ist bin ich auch nicht sicher.

Gerade letzten Versuch für heute gemacht mit Adresse B02:D00:F0 Adresse und nur DEV_PORT = 0, das klappte nicht.

Ich bleibe dran....danke & bis demnächst

 

Link to comment
Share on other sites

On 4/7/2021 at 7:04 PM, Tiras said:

Probier mal:

[System Network 1]

DEV_BUS = B02:D00:F0

DEV_PORT = 0

#PCI_SWITCH_PORT = -1

Es scheint mit Logik alleine kommt man da nicht weiter. sowohl der Wert aus lspci (DEV_BUS = B02:D00:F0) mit Angabe "PCI_SWITCH_PORT = 3" oder ohne , als auch lspci -vtnn, wo man sehen kann dass eth0 auf PCI Switch 00:1c.2 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 3 (rev 0e)+-1c.2-[02]----00.0  Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136] ergibt (DEV_BUS = B00:D28:F0), die Netzwerkschnittstelle kommt nicht hoch, kein link angezeigt und nur loopback da. Hat jemand noch eine Idee?

Link to comment
Share on other sites

6 hours ago, Tiras said:

Leider nein, und da ich mein Problem auch nicht beheben kann, bin ich wieder auf unraid umgestiegen.

schade - sehr bedauerlich, aber auch verständlich. Scheint sonst eh niemand mehr da zu sein...na dann - alles Gute & viel Glück!

Link to comment
Share on other sites

  • 2 weeks later...

Hallo Zusammen,

 

ich habe ein kleines Problem. Ich schaffe es zwar ein QNAP Modell auszuwählen und auch zu installieren, auf die Weboberfläche komme ich ebenfalls. Sobald ich jedoch versuche mich anzumelden, lädt das ganze unendlich lange. Ich habe bereits das QNAP Modell gewechselt, jedoch habe ich hier das Problem das ich mich gar nicht erst Anmelden kann. Ich hoffe einfach mal das mir einer von euch helfen kann. Schonmal vielen Dank im vorraus! 

Link to comment
Share on other sites

  • 2 weeks later...

Ich habe das zwar zum laufen gebracht nach der Anleitung


allerdings etwas verfeinert und aktualisiert nach letzten Updates

MODEL_TYPE="QY380_QY390_10_11"
PATCHED_FIRMWARE="TS-X85_20210406-4.5.2.1630"
DOWNLOAD_URL="https://download.qnap.com/Storage/TS-X85/"

sed -i "s|MODEL_TYPE=\".*\"$|MODEL_TYPE=\"$MODEL_TYPE\"|" my_create_qnap_boot
sed -i "s|PATCHED_FIRMWARE=\".*\"$|PATCHED_FIRMWARE=\"$PATCHED_FIRMWARE\"|" my_create_qnap_boot
sed -i "s|DOWNLOAD_URL=\".*\"$|DOWNLOAD_URL=\"$DOWNLOAD_URL\"|" my_create_qnap_boot

head -n10 my_create_qnap_boot

jedoch ist die VM nicht im Netzwerk sichtbar

grafik.thumb.png.15fd05e68d781f3567d41459829fbe36.png

Link to comment
Share on other sites

Hallo,

Ich habe dieses Forum schon durchgelesen und versucht, mir eine QNAP auf einer virtuellen Instance zu installieren. In mienem Fall ist es ein Unraid Server

Leider klappt die Installation nicht, weil aus irgendeinem Grund die Platten nur readonly sind. siehe auch die Screenshots, die ich gemacht habe:

grafik.png.61fc4a23e7dd27ed075cec5e8d154219.png

 

Hier die Einstellungen, mit denen ich das Script gestartet habe:

grafik.png.659bce12321a0ee76d86043d0b2a4f8e.png

 

Ich habe schon alle möglichen Schnittstellen probiert, auch mal die Festplatten getauscht, andere probiert. Will nicht klappen. Ich komme immer wieder hier raus.

Ich habe den Verdacht, das es nur was kleines ist, aber ich finde es nicht.

 

Kann mich einer mal erleuchten? Hat es schon jemand auf einem Unraid geschafft?

 

Pasadena

Link to comment
Share on other sites

Need some help to get Qnap running with Network on Proxmox as it needs e1000e nic

 

I added 

args: -netdev type = tap, id = net0, ifname = tap102i0 -device e1000e, mac = 6E: 7B: 02: 79: A8: B0, netdev = net0, bus = pci.0, addr = 0x12, id = net0

to vm conf file

If I try boot into tiny core, no ip from dhcp but it shows nic is there

 

 

 

Capture.PNG

Edited by Hemps
Link to comment
Share on other sites

  • 2 weeks later...

Hi all, i still have an issue to get this running on a J4105B system with 2 onbard SATA ports an 4 additional ports on an Asmedia PCIE card. Trying 653B the two onboard ports and two ports on the card are working, but HDs are wrongly interpreted as PCIE M2 disks and appear mirrored in the UI. This doesn't look good for me but in fact, 2 of the ports are working with the following setup

 Intel SATA lspci 00:12:0, dezimal B00:D18:0 DevPort 0 and 1

ASMedia SATA  lspci 01:00:0, lspci -vtnn 00:13:0 dezimal B00:D19:F0, DevPort 0 and 1

 

does anyone know how to define multiple controllers in model.conf for the remaining two ports, or how to find out the coorct values for all parameters?

simply translating the PCI address into decimal doesn't work, using translation via lspci -vtnn to find the bridge address (01:00:0 to 00:13:0) is also not sufficient. DevPort 3 and 4 don't work

Does anyone know the meaning of PCI Switch Port that appears at two entries?

  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...
On 4/19/2021 at 4:57 PM, CillitBang69 said:

Hallo Zusammen,

 

ich habe ein kleines Problem. Ich schaffe es zwar ein QNAP Modell auszuwählen und auch zu installieren, auf die Weboberfläche komme ich ebenfalls. Sobald ich jedoch versuche mich anzumelden, lädt das ganze unendlich lange. Ich habe bereits das QNAP Modell gewechselt, jedoch habe ich hier das Problem das ich mich gar nicht erst Anmelden kann. Ich hoffe einfach mal das mir einer von euch helfen kann. Schonmal vielen Dank im vorraus! 

das ist ziemlich normal, zumindest am Anfang nach einer Neu-Installation. Scheint auch von der CPU abzuhängen, und von RAM Ausstattung.

Link to comment
Share on other sites

On 5/19/2021 at 7:31 PM, Himem said:

Hi all, i still have an issue to get this running on a J4105B system with 2 onbard SATA ports an 4 additional ports on an Asmedia PCIE card. Trying 653B the two onboard ports and two ports on the card are working, but HDs are wrongly interpreted as PCIE M2 disks and appear mirrored in the UI. This doesn't look good for me but in fact, 2 of the ports are working with the following setup

 Intel SATA lspci 00:12:0, dezimal B00:D18:0 DevPort 0 and 1

ASMedia SATA  lspci 01:00:0, lspci -vtnn 00:13:0 dezimal B00:D19:F0, DevPort 0 and 1

 

does anyone know how to define multiple controllers in model.conf for the remaining two ports, or how to find out the coorct values for all parameters?

simply translating the PCI address into decimal doesn't work, using translation via lspci -vtnn to find the bridge address (01:00:0 to 00:13:0) is also not sufficient. DevPort 3 and 4 don't work

Does anyone know the meaning of PCI Switch Port that appears at two entries?

Update: when un / replugging the 2 SATA Ports which are not recognized, those start working until next reboot, also in QNAP GUI. Issue might be caused by ASMEDIA 1061 chip which is a 2 port controller, and I guess on the card is a port multiplier which might not be work 100% as a native controller. This card works fine for Knoppix, Ubunto etc, also in TinyCore and QNAP terminal all disks are visible, but not work in QNAP Gui Applications after first reboot

  • Like 1
Link to comment
Share on other sites

  • 1 month later...
On 6/20/2021 at 1:36 PM, Himem said:

Update: when un / replugging the 2 SATA ports which are not recognized, those start working until next reboot, also in QNAP GUI. Issue might be caused by ASMEDIA 1061 chip which is a 2 port controller, and I guess on the card is a port multiplier which might not be work 100% as a native controller. This card works fine for Knoppix, Ubunto etc, also in TinyCore and QNAP terminal all disks are visible, but not work in QNAP Gui Applications after first reboot

Hi there,

 

if ASMEDIA works properly on other Linux distro, i would check the loaded modules and try to match as much as possible in the qnap image. If you need any additional modules you can compile them using the standard kernel source tree and try.

Link to comment
Share on other sites

  • 2 weeks later...
On 7/26/2021 at 7:25 PM, pocopico said:

Hi there,

 

if ASMEDIA works properly on other Linux distro, i would check the loaded modules and try to match as much as possible in the qnap image. If you need any additional modules you can compile them using the standard kernel source tree and try.

Hi PocoPico, as I assumed ealier it was because the controller is a 2 port controller with port multiplier, I got a 4 port controller and this works fine. There are Asmedia 1061 cards on the market with port multiplier and 4 connectors. those are not working properly. The native 2 ports work fine but the additional two do not. It is not an issue with the SATA driver for the 1061 chip itself, this is supported by QNAP package

Edited by Himem
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...