djf

DSM 5.0-4493 Update 7

Recommended Posts

Ignoring the fact that update 6 seems to have been skipped, has anyone successfully applied v7. Because of the issues with update 5, I'm reluctant to be a guinea pig!

Share this post


Link to post
Share on other sites

Thanks for the update - has anyone performed the upgrade on a bare metal system (ideally an HP N54L!) as well as a VM?

Share this post


Link to post
Share on other sites

little bit scary, the update took less than 4 secs. and worked (VM based system)

 

Also patched Baremetal system - all ok

Edited by Guest

Share this post


Link to post
Share on other sites
Thanks for the update - has anyone performed the upgrade on a bare metal system (ideally an HP N54L!) as well as a VM?

 

Worked OK for me VM setup

Share this post


Link to post
Share on other sites

It went OK after a hard reboot (it was stuck after automatic reboot).

 

Before: 5.0-4493 U3

After: 5.0-4493 U7

 

Setup: nanoboot on ESXi 5.5 VM - HP N54L

Share this post


Link to post
Share on other sites

Haven't noticed anything yet. I am running Downloadstation, Virtualboxphp, Serviio, Couchpotato, and various shares (with built in Samba)

Share this post


Link to post
Share on other sites
Did you have any issues with permissions, loss of volume and disk, like with update 5?
No, nothing bad did occur :wink:

Share this post


Link to post
Share on other sites

I just updated from 4 to 7. Using the normal sed update method.

I had volume unmount issues, disk temp alerts -1°C ? Also had some permissions go from shares!!

 

The volume and disk issues went away after a power off and an extra reboot.

The Permissions, had create by hand again.

 

Seems ok now.

 

HP N54L (bare metal) with nanoboot

Share this post


Link to post
Share on other sites

Same for me - update from 4 to 7. All fine after a few reboots and reapplying user rights.

Also HP N54L "bare metal" and NanoBoot 5.0.3.1.

Share this post


Link to post
Share on other sites
Accidently I have installed the update 7 without logging in to SSH first and do the commands:

sed 's/flashupdateDeb/flashupdateDeb1/' /autoupd@te.info > /autoupd@te.info1

mv /autoupd@te.info1 /autoupd@te.info

 

But everything seems to be ok... No unmounted volumes, access rights are ok. :grin:

 

Check what version you have. You're probably still on previous update, since the sed commands trick the updater into going through with the update.

Share this post


Link to post
Share on other sites

I did the same thing also, updated my Xpenology box without the SSH command and my DSM version is also showing up as Update 7. All files and permission are intact. Strange!

 

Another strange thing that I found out is that my real Synology box, a DS110j, does *NOT* show Update 7 when I checked for updates. It's currently at DSM 5.0-4493 Update 5 and according to the status, it is still up-to-date. Maybe the shell shock security issue doesn't affect ARM-based Synology NAS?

Share this post


Link to post
Share on other sites
I did the same thing also, updated my Xpenology box without the SSH command and my DSM version is also showing up as Update 7. All files and permission are intact. Strange!

 

Another strange thing that I found out is that my real Synology box, a DS110j, does *NOT* show Update 7 when I checked for updates. It's currently at DSM 5.0-4493 Update 5 and according to the status, it is still up-to-date. Maybe the shell shock security issue doesn't affect ARM-based Synology NAS?

 

DS110j do not suffered from shellshock venerability, therefore no update for that

Share this post


Link to post
Share on other sites

Only these boxes suffer from the shellshock bug.

 

15-series: DS415+

14-series: RS3614xs+, RS2414+, RS2414RP+, RS814+, RS814RP+, RS3614xs, RS3614RPxs

13-series: DS2413+, DS713+, RS10613xs+, RS3413xs+, DS1813+, DS1513+

12-series: DS712+, DS1512+, DS1812+, DS3612xs, RS3412xs, RS3412RPxs, DS412+, RS812+, RS812RP+, RS2212+, RS2212RP+

11-series: DS3611xs, RS3411xs, RS3411RPxs, DS2411+, RS2211+, RS2211RP+, DS1511+, DS411+II, DS411+

10-series: DS1010+, RS810+, RS810RP+, DS710+

 

So only the beefcake models.

Share this post


Link to post
Share on other sites

update OK from Hyper-V with update 5 , even no need to reboot

 

update OK from native Proliant N54L with update 4 : need to reboot 3 times (so i got same issue when i did the upgrade from update 4 to update 5) as volumes were unmounted

i lost permissions and folders set on the backup function

 

but the best for the end !! apparition of Box , Hubic , OneDrive on Cloud Sync !! alleluiaaaaa no need to wait for DSM 5.1 , tested all of them and works like a charm , that makes my day :smile:

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.