Rorschach

XPEnology Hardware Compatibility List

Recommended Posts

green = works perfectly

yellow = works with workaround/some Feature don't working

red = don't work

 

Bare Metal Solution:

GnoBoot 10.5 Alpha

Mainboards:

Asrock Q1900DC-ITX

Gigabyte GA-C1037UN-EU

PCI/e Cards:

Generic (Jmb363) - 4-Port Internal SATA2 Raid Controller Works with hacked NON-RAID, AHCI or IDE BIOS, Original RAID Mode BIOS don't work. Download

Syba SI-PEX40064 (Marvell 88SE9215) - 4-Port Internal SATA3

 

Nanoboot 5.0.3.1

Mainboards:

ASUS H61M-A

Gigabyte GA-C1037UN-EU

USV/UPS:

APC Back-UPS CS 325VA 230V

 

Nanoboot 5.0.3.2

Mainboards:

Asrock Q1900DC-ITX Wake on LAN don't work -> Driver Problem in Nanoboot Driver, Rest works perfectly

PCI/e Cards:

Generic (Jmb363) - 4-Port Internal SATA2 Raid Controller

Syba SI-PEX40064 (Marvell 88SE9215) - 4-Port Internal SATA3

 

Virtual Solution:

ESXi Server

Mainboards:

Asrock Q1900DC-ITX

Intel DQ77KB / Nanoboot 5.0.3.2 For using both LAN NIC's a Driver needs to be injected into the Image Tutorial

Edited by Guest

Share this post


Link to post
Share on other sites

I just thought, I start a Hardware Compatibility List, that people can contribute and share there experiences with Hardware Compatibility on XPenology.

 

If you have a different Hardware, please insert it in this Thread. I will add it into the first post of this Thread.

Share this post


Link to post
Share on other sites

I have a system with core i3 3240 with 8gb memory on motherboard asus h61m-a socket lga 1155.I have instaled nanoboot 5.3.0.1 and synology 5.0 4493 update 5.Everything works flawlessly.

The system recognizes also my UPS by APC.

 

 

Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites

Okay, that are many informations =). I think near every HDD should work.

 

Most important information should be Mainboard, Addon cards (RAID Cards, Adapter, and all this stuff which need aditional drivers) =)

Also I have added your UPS

Share this post


Link to post
Share on other sites

Intel DQ77KB works perfectly (my impression as dummy) under ESXI / Nanoboot 5032.

It has g2 LAN Ports, to use both you have to inject a driver for the Intel 82579LM in the Image before istalling.

 

In IDLE under ESXI with 16GB Ram + 3,5" HD + 2,5" HD it needs just ~23W.

Share this post


Link to post
Share on other sites

Bare Metal : Mainboard Gigabyte C1037UN-EU, 8 gb ram, 2X Toshiba DT01ACA200, 1 X Seagate ST980813ASG, works fine with Nanoboot 5.0.3.1 DSM 5.0-4493 update 5 and with synoBoot XPEnology DS3612xs DSM 4.3 build 3810++ (repack v1.0) update 4

Edited by Guest

Share this post


Link to post
Share on other sites

All Mainboards added. Thx for contribution.

 

@jagwaugh you have Baremetal or Virtual Solution (ESXi, Hyper-V). Do you use Nanoboot, Gnoboot, Synoboot?

Share this post


Link to post
Share on other sites

Sorry, should have given more detail.

 

Baremetal, Nanoboot latest, booting from cd burn with latest .iso.

 

I am just trying to crosscompile a few things, I'd like to be able to use the CD, at least from the terminal.

 

It is not bad for fairly aged hardware, CPU &Mem go to the wall with virtualbox, but it worked, had a high cpu usage with ffmpeg under serviio, changed the dlna profile for my tv and that got a LOT better.

 

Andrew

Share this post


Link to post
Share on other sites

Hardware: Lenovo ThinkServer TS140 70A4000HUX i3-4130 3.4GHz Server with 4GB ECC memory.

PCI-E: Intel EXPI9301CTBLK installed in 1x slot

USB: ADATA Superior Series S102 PRO 32 GB USB 3.0 Flash Drive AS102P-32G-RGY

 

I installed Nanoboot 5.0.3.2 with DSM 5.0-4493 X64 then installed Update 5. I am using the built-in i217 NIC and the Intel EXPI9301CTBLK in a BOND setup.

 

Installed without any issue, using 3 x 4TB WD Red drives.

 

NOTE: I got a private message from unmesh asking if I am using UEFI boot vs legacy and power usage. I can't seem to reply to private messages. In any case, I will double check later today/tomorrow, and update. 9/25/14

 

NOTE: I checked my TS140, and it is set to be AUTO in terms of BIOS mode. It will use UEFI or Legacy depending on O.S. installed, at least that is how I read the BIOS settings. I am not sure which one xpenology uses. As for the power usage, initial power on with 3 4TB WD Red drives hits about 70watts, and when everything is running, it idles at around 30 - 35 watts. While doing a parity check of volume, the system fluctuates from 37 - 45 watts.

Edited by Guest

Share this post


Link to post
Share on other sites

Intel DN2800MT, ATOM D2800, 4GB, works fine with synoBoot and XPEnology DS3612xs DSM 5.0 beta

 

but

 

Gigabyte GA-J1900N-D3V does not work as not able to boot without Screen and without Keyboard.

Share this post


Link to post
Share on other sites

Intel core 2 duo e6600, Gigabyte G41M combo board, 8 GB dyanet ddr3 ram, onboard vga, asm 1061 esata + sata card, 3com gigabit PCI NIC and built in motherboard marvell network controller, 2 X 1 TB WD Black drives in RAID 1, , 4 x 2TB seagate drives in RAID 5, Sandisk 4GB usb drive

 

Bare metal setup : nanoboot 5.031, DSM 5-04558 update 5

Edited by Guest

Share this post


Link to post
Share on other sites

Mainboard:

Asus P5Pe-VM

Intel e4600 (Core 2 Duo)

Internal VGA and AGP Radeon 3800

 

Would not work straight away with Nanoboot-5.0.3.2 DSM 5.0-4493 X64

Works with XPEnology DS3612xs DSM 4.3 build 3810++ (repack v1.0)

Upgrade to Nanoboot-5.0.2.4 DSM 5.0-4482 X64 and then Nanoboot-5.0.3.2 DSM 5.0-4493 X64 and the update 5.

 

Does not work with: Gnoboot-10.5 DSM 5.0-4458 X64

 

Evrything seems to work.

 

Full mobo specs: http://www.newegg.com/Product/Product.a ... 6813131029

Share this post


Link to post
Share on other sites

Netgear ReadyNAS Pro 6 system with DSM 5 update 5 and Nanoboot 5.0.3.2:

 

- Mainboard: Netgear x86 socket 775 mini ITX

- CPU: Q6600 Quad-Core 2.4 GHz

- Memory 4GB DDR2

- Chipset: ICH8R with 6x SATA disk via pci-e x1

- 2x Network: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller

- VGA: Q965 Integrated Graphics Controller

- BIOS: Winbond W25x80

Share this post


Link to post
Share on other sites

Bare metal

Mobo:Supermicro X10SLM-F

CPU: Intel Xeon E3-1275v3

RAM: 4GB ECC DDR3 UDIMM

SAS Card: LSI 9211-8i in IT mode

Nanoboot 5.0.3.1

DSM 5.0-4493 update 7

 

All 6 onboard SATA work

All 8 LSI SAS ports work

Both onboard Intel network ports work with WOL

 

Pretty much everything works.

Share this post


Link to post
Share on other sites

HP N54L works perfectly :razz:

 

Also for UPS - CyberPower Value 600E is detected fine and shuts down the NAS when on battery power after the time set. I'd assume that most of the CyberPower range would work.

Share this post


Link to post
Share on other sites

Bare Metal

 

Case: Silverstone DS380

Power supply: Silverstone ST45SF-G modular (450W, 80 Plus Gold)

Motherboard: Asrock Z87E-ITX

RAM: Kingston DDR3 4GB * 2

CPU: Haswell Celeron G1840

SAS: IBM M1015 SAS cross flashed to 9211-8i IT

USB: Sandisk USB 3.0 UltraFit 16GB

Nanoboot 5.0.3.1

DSM 5.0-4493 update 7

 

After cutting the plastic inside the DS380 case, I can use all of the 8 bays in the chassis.

http://gadgets.williamwan.hk/2014/10/03 ... -plug-nas/

Share this post


Link to post
Share on other sites

Hello Everybody!

 

I'm new here. My success story: FOXCONN R10-D2/2GB RAM/Kingston Data Traveller 1GB for boot. Sata drive installed and works properly. All running with XPEnoboot for DSM5.1 ver. DS3615xs 5.1-5022.1, downloaded from http://xpenology.pety.me. Sorry for my english language.

Share this post


Link to post
Share on other sites

Case: Zalman ZM-T1 Plus

Power supply: FSP 460-60HCN

Motherboard: Asus C60M1-I (with integrated AMD APU C-60 1.0GHz Dual-Core)

RAM: 2GB DDR3

USB Flash: OLTRAMAX 8GB 50

UPS: Powercom Imperial IMD-825AP

Storage: 1x2.5 HDD

 

Loader: XPEnoboot 5.1-5022.3 (DS3615xs)

DSM: 5.1-5022 Update 4

 

Energy use: ~ 30 W

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.