Driver extension jun 1.03b/1.04b for DSM6.2.2 for 3615xs / 3617xs / 918+

[IG-88]

2 hours ago, mydownload said:

any other idea ?

my last post had some, you can try to pick up newer hpsa controller like 420 that can be switched into hba mode but you might end up in the same spot as you are now

if it has to be baremetal i guess another nas system might work better (true nas, open media vault)

afair most people with hpsa controllers switched to hypervisor and used dsm as vm

[mydownload]

that's strange, few years ago, i've already succeed to install it from Xpenoboot but i don't remerber which release it was, my usb key has died after an electrical powerdown...

 

thanks,

[mydownload]

So, i've started from scratch, with XPEnoboot_DS3615xs_5.2-5644.5 and DSM_DS3615xs_5644.pat. So it's installed BUT, i have only one HD instead of 4... All HD have the same config : Raid0 on my controller.

 

any idea why ?

Edited April 8, 2022 by mydownload

[mydownload]

4 hours ago, mydownload said:

So, i've started from scratch, with XPEnoboot_DS3615xs_5.2-5644.5 and DSM_DS3615xs_5644.pat. So it's installed BUT, i have only one HD instead of 4... All HD have the same config : Raid0 on my controller.

 

any idea why ?

I didn't correctly look at... all HD are seen like a raid partition. So, now, how can i updgrade my NAS without loosing my configuration (raid array) ?

 

thanks

[IG-88]

7 hours ago, mydownload said:

I didn't correctly look at... all HD are seen like a raid partition. So, now, how can i updgrade my NAS without loosing my configuration (raid array) ?

you can boot from a usb with loader 1.03b (prepared with the correct vid/pid) and try to upgrade the installed 5.2 to 6.2, if the only system was to create partitions the you will ship that step as there are already configured partitions but my guess is that if there is da driver issue with hpsa on 6.2 that attempt will fail, but the ony thing you can loose is a fresh installed 5.2 so not much risk trying it

[mydownload]

10 hours ago, IG-88 said:

you can boot from a usb with loader 1.03b (prepared with the correct vid/pid) and try to upgrade the installed 5.2 to 6.2, if the only system was to create partitions the you will ship that step as there are already configured partitions but my guess is that if there is da driver issue with hpsa on 6.2 that attempt will fail, but the ony thing you can loose is a fresh installed 5.2 so not much risk trying it

With 1.03b, actual installation is not seen... I really need to keep drivers from XPEnoboot5.2...

[IG-88]

3 hours ago, mydownload said:

With 1.03b, actual installation is not seen... I really need to keep drivers from XPEnoboot5.2...

its not that simple, 5.2 used its own compiled kernel, with 6.0 we use synology's original kernel with all its messy mod's and one sided changes, if they change something in the kernel they dont core if other things break as long as the hardware they use in there own units works and beside the kernel changes there are also external drivers they use (and mod) and dont offer source code

especially when using a older kernel source (or even original from kernel.org) to compile drivers there is always a risk of things not working properly

we hat to use 6.x beta source as base for a long time for drivers and with every update synology made the gap between source used for additional drivers and the source used (by synology) for the kernel grew and if that sap is 1-2 years there might be "some" differences

 

in general using dsm in a way where raid controllers are involved is not the way its meant to be used as its build all around software mdadm raid with single disks and using raid0 disks as single drives in dsm will result in disks without smart info, no serial number (no way of telling what IRL disk broke from the dsm gui) and will kill a lot of the easy/safe to use features dsm is meant to deliver

like it is with making usb drives part of dsm's raid sets, one can tweak it like that but its a terrible idea to do so

also as further you stray away from its original config you will have much more trouble when updating

 

in your situation its way better to get around it with other ways like hypervisor (that one will handle hardware raid management  and use its software to monitor the disks and even message you in case of problems properly) or using a controller that is better suited for the task of natively running in dsm on a bare metal system (like the lsi sas in 3615/3617/3622 where the driver is native part of dsm)

 

PS: you can debug the whole hpsa thing if you want and fix it, i would add you patches to the kernel source and make new drivers but the amount of time needed for that would be way to big on your side and might be better invested in using these skills to backport intel igc driver (2.5G nic) or backport recent i915 driver to have intel qsv support for newer cpu's

(a older lsi sas is less then 100 bugs and using proxmox costs nothing - compared to 20+ work hours for fixing hpsa drivers for dsm)

[mydownload]

Thanks for your time IG-88 !!!

 

this server were used for Surveillance station (hacked), with 6 cams. it's not really urgent for me, so, if you could create HP drivers, i will be your indebted for life !!

 

what must i do for this ?

 

thanks,

[IG-88]

4 hours ago, mydownload said:

if you could create HP drivers,

 

On 4/9/2022 at 1:42 PM, IG-88 said:

PS: you can debug the whole hpsa thing if you want and fix it, i would add you patches to the kernel source and make new drivers but the amount of time needed for that would be way to big on your side and might be better invested in using these skills to backport intel igc driver (2.5G nic) or backport recent i915 driver to have intel qsv support for newer cpu's

(a older lsi sas is less then 100 bugs and using proxmox costs nothing - compared to 20+ work hours for fixing hpsa drivers for dsm)

 

only if you (any one else) can find out whats wrong with the hpsa driver in syno's kernel, code a fix and deliver a patch for the driver source (or the whole fixed driver source)

just compiling a driver did not do the trick (in 6.1/6.2 we tried that with the kernl driver and the one from external source already)

[mydownload]

On 4/10/2022 at 2:18 PM, IG-88 said:

 

 

only if you (any one else) can find out whats wrong with the hpsa driver in syno's kernel, code a fix and deliver a patch for the driver source (or the whole fixed driver source)

just compiling a driver did not do the trick (in 6.1/6.2 we tried that with the kernl driver and the one from external source already)

is there any log when booting USB ?

[mydownload]

About my issues : i've got a new server, Dell R310, with LSI card and i've added an old Intel Pro network card. Succed to install DSM6.2 with redpill.v0.4.6.

 

BUT, it seems configuration is not backuped, every time i reboot it, i need to reinstall Surveillance station and cracked it again. Does someone have an idea about reason ?

 

thanks,

[IG-88]

On 4/12/2022 at 5:09 PM, mydownload said:

is there any log when booting USB ?

its redirected to com1, if you have that and use a null-modem cable you can use terminal program like putty to display that (on another computer)

 

On 4/15/2022 at 9:47 AM, mydownload said:

Succed to install DSM6.2 with redpill.v0.4.6.

this thread is about dsm 6.2.2 and jun's loader so we are done here i guess

please open new topic in another area

 

[xenpology]

@IG-88

I am on DSM 7.1.1.

I got the Club 3D 2.5GB Adapter plugged in a USB3 Port at my Nas

Xpenology 920+ but the CPU is a XEON 1225 V3

I could only install the gemini lake

r8152-geminilake-2.15.0-3.spk so far cuz other packages arent supported - DSM is complaining.

 

Is there any chance to make it work or do i have to switch to a xpenology version that recognize my Xeon CPU?

[IG-88]

17 hours ago, xenpology said:

Xpenology 920+ but the CPU is a XEON 1225 V3

off topic here as this thread is about dsm 6.2.2 but dsm 7.1.1 still has the same i915 driver as in 6.2.3

the driver should detect older gpu's as well, only newer gpu's are a problem

this CPU has "Intel HD P4600" and thats gpu gen 7.5

https://en.wikipedia.org/wiki/Intel_Graphics_Technology

 

so its capability's are limited and there is no guarantee that it will work video station of the face recognition in photos

if there are devices in /dev/dri then the driver is working, your main problem will be is it working with the part of dsm you want to use, as synology did not intent or test if older gpu's will work

what a 7th gen gpu can do can be seen here (compared with newer gpu's)

https://en.wikipedia.org/wiki/Intel_Quick_Sync_Video#Hardware_decoding_and_encoding

no HEVC/h.265 for sure

 

[Orphée]

FYI, with DS3622xs+, i915 driver is not needed at all for face recognition in Synology Photos.

So depending on user needs, using a loader like DS3622xs+ would be easier if not planned to do HW transcoding for video.

[xenpology]

@IG-88

Thanks, sry for the off topic. Didnt see.

I dont mind about HW Transcoding, just wanna run the 2.5Gbit Adapter. Need to figure out how. The installed gemini lake driver doesnt give me a third entry under network attachments for the dongle so far. Before on a org. Synology it was working flawless.

[IG-88]

On 4/30/2023 at 7:00 PM, xenpology said:

Is there any chance to make it work or do i have to switch to a xpenology version that recognize my Xeon CPU?

my interpretation here war that it was about the gpu not being recognized, cpu wise there is nothing to recognize, it just works

if its a bout what you seen in dsm's gui, then dont worry it just a kind of static picture they persent the user but if its important, there is a cpuinfo tool in the software modding section that can make your real cpu to be seen in the gui

 

4 hours ago, xenpology said:

I dont mind about HW Transcoding, just wanna run the 2.5Gbit Adapter. Need to figure out how. The installed gemini lake driver doesnt give me a third entry under network attachments for the dongle so far. Before on a org. Synology it was working flawless.

arpl loader has its own r8152 driver (version=v2.16.3 (2022/07/06)) that should be working

boot with the usb adapter connected and check if the driver is loaded with "lsmod |grep r81"

also check whats in the log about that with "dmesg |grep r81"

[Davide03gm]

Hi, I would like to solve my problem.

 

I have an HPE microserver Gen8:
Intel Xeon E3-1220Lv2 CPU
RAM 16 GB
4x HDD and 1x SSD disks (RAID controller disabled)
2x integrated 1 gigabit/s ports

 

I use arpl for boot DSM

 

I would like to add an HP NC523 SFP NIC to my configuration, Synology does not detect the card but the HPE server detect it as a QLogic 82XX NIC and activates the SFP ports

 

Is it a problem of missing the right driver in the loader configuration or something similar?

 

thanks for help

Edited January 8 by Davide03gm

[IG-88]

 

 

HEP Spec lists it as "QLogic cLOM8214"

https://www.hpe.com/psnow/doc/c04111574.pdf?jumpid=in_lit-psnow-getpdf

 

the driver would be "qlcnic.ko" and that driver was part of the 3615/17 extra package

pci vendor and device id in the driver are

1077:8430

1077:8030

1077:8020

 

check if the pci id's match, check log dmesg about "qlogic" or "qlcnic"

that driver was also part of jun's original extra.lzma so most likely its not about the driver being present

 

afair 6.2 update support ended 6/2023 so you might be better off trying out a newer loader and dsm 7.x

[Orphée]

He is probably using DSM 7 already as he referred to ARPL.

[IG-88]

On 1/8/2024 at 2:43 PM, Davide03gm said:

I use arpl for boot DSM

 

 

On 1/11/2024 at 9:31 PM, Orphée said:

He is probably using DSM 7 already as he referred to ARPL.

 

YES you are right i did not read careful enough but the driver required is correct and arpl seems to to have that one, as arpl is unmaintained atm i'd suggest using ARC loader

https://github.com/AuxXxilium/arc

that one comes with a wider selection of drivers and to be sure i just checked for that driver and it is present there, so it should work with this loader

 

[ed_co]

On 1/22/2022 at 7:23 AM, rcached said:

 

 

Confirmed links are dead for all but the DS3615 file.

 

New mirror links below.  Please consult the OP for any additional info needed!

 

0.8_syno ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_syno
Original: https://gofile.io/d/mVBHGi
Filename: extra918plus_v0.8_syno.zip
SHA256: 21B0CCC8BE24A71311D3CC6D7241D8D8887BE367C800AC97CE2CCB84B48D869A
Mirrors: Clicknupload, Dailyuploads, usersdrive, Zippyshare

 

0.8_std ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_std
Original: https://gofile.io/d/y8neID
Filename: extra918plus_v0.8_std.zip
SHA256: F611BCA5457A74AE65ABC4596F1D0E6B36A2749B16A827087D97C1CAF3FEA89A
Mirrors: Clicknupload, Dailyuploads, usersdrive, Zippyshare

 

0.8_recovery ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_recovery
Original: https://gofile.io/d/4K3WPE
Filename: extra918plus_v0.8_recovery.zip
SHA256: 5236CC6235FB7B5BB303460FC0281730EEA64852D210DA636E472299C07DE5E5
Mirrors: Clicknupload, Dailyuploads, usersdrive, Zippyshare

 

DS3615: extra.lzma for loader 1.03b_mod ds3615 DSM 6.2.2 v0.5_test
Original: https://gofile.io/d/iQuInV
Filename: extra3615_v0.5_test.zip
SHA256: BAA019C55B0D4366864DE67E29D45A2F624877726552DA2AD64E4057143DBAF0
Mirrors: Clicknupload, Dailyuploads, usersdrive, Zippyshare

 

DS3617: extra.lzma for loader 1.03b_mod ds3617 DSM 6.2.2 v0.5_test
Original: https://gofile.io/d/blXT9f
Filename: extra3617_v0.5_test
SHA256: 4A2922F5181B3DB604262236CE70BA7B1927A829B9C67F53B613F40C85DA9209
Mirrors: Clicknupload, Dailyuploads, usersdrive, Zippyshare

 

Links are dead!!
Can anyone please share all the 08_syno/std/recovery for ds918+?
Thank you very much in advance!!

 

EDIT: nevermind, I was trying to find it for DSM 6.2.3!!

Edited April 9 by ed_co

[rcached]

On 4/9/2024 at 1:38 PM, ed_co said:

Links are dead!!
Can anyone please share all the 08_syno/std/recovery for ds918+?
Thank you very much in advance!!

 

EDIT: nevermind, I was trying to find it for DSM 6.2.3!!

Edited Tuesday at 02:28 PM by ed_co

 

Glad you were able to find working links for DSM 6.2.3 instead.

 

On the off chance that you or anyone else may need the downloads in this thread for DSM 6.2.2, here are fresh download links:

 

0.8_syno ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_syno
https://gofile.io/d/Otg1w4

SHA256: 21B0CCC8BE24A71311D3CC6D7241D8D8887BE367C800AC97CE2CCB84B48D869A

https://dailyuploads.net/75vcrg61rsn2

https://usersdrive.com/qhwiez556u7k.html
https://www.zippyshare.day/QkM1RuCZ4WGjJ91/file

 

0.8_std ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_std
https://gofile.io/d/rlPLhM
SHA256: F611BCA5457A74AE65ABC4596F1D0E6B36A2749B16A827087D97C1CAF3FEA89A
https://dailyuploads.net/l1v9vaob0k4o
https://usersdrive.com/xyepa6sa4trc.html
https://www.zippyshare.day/NB0AjRJhSL9nRGT/file

0.8_recovery ds918+ - extra.lzma/extra2.lzma for loader 1.04b_mod ds918+ DSM 6.2.2 v0.8_recovery
https://gofile.io/d/dBMD5e
SHA256: 5236CC6235FB7B5BB303460FC0281730EEA64852D210DA636E472299C07DE5E5
https://dailyuploads.net/t4grkc3s2hfs
https://usersdrive.com/f28dhpmbjlkf.html
https://www.zippyshare.day/QxWHH3jJ0Q6BvzK/file

 

DS3615: extra.lzma for loader 1.03b_mod ds3615 DSM 6.2.2 v0.5_test
https://gofile.io/d/Q8V9iR
SHA256: BAA019C55B0D4366864DE67E29D45A2F624877726552DA2AD64E4057143DBAF0
https://dailyuploads.net/c8y9jyunl0wg
https://usersdrive.com/nn6ja92hy8a2.html
https://www.zippyshare.day/U9uxXCwpnXwrSlk/file

DS3617: extra.lzma for loader 1.03b_mod ds3617 DSM 6.2.2 v0.5_test
https://gofile.io/d/44u6er
SHA256: 4A2922F5181B3DB604262236CE70BA7B1927A829B9C67F53B613F40C85DA9209
https://dailyuploads.net/fje0te8ywo9a
https://usersdrive.com/wjsojq787h5w.html

https://www.zippyshare.day/z4Lf0av9njH5dLx/file

Edited Friday at 10:40 AM by rcached

[and-vasilets]

Здравствуйте! Нужен ваш совет...Я пытаюсь поставить DSM с загрузчиком Arc Loader 24.4.10 на ПК Ryzen 5600G + MCI tomahawk b550... конфигурирую загрузчик под модели Synology c AMD процессором, перепробовал все модели!!! Доходит до того момента, когда Arc Loader выдает локальный адрес http://IP:5000 и на этом все...загрузки DSM не происходит, синолоджи ассистент устройство не находит, более того, через пару минут вообще пропадает устройство с указанным ай пи в локальной сети (у меня Кинетик Гига, и я это вижу в админке роутера) а когда только Arc Loader выдал что можно зайти по http://IP:5000, скорость порта 10мбт/с причем лан порт материнки поддерживает 2,5 Гбт/с. Я думал что не видит этот порт и ставил PCI-E гигабитный контроллер лан...все тоже самое...останавливается все тогда, когда в сети лан должно появиться устройство Synology и должна начаться установка DSM. Я в этом всем профан полнейший и наверняка не вижу чего-то элементарного, поэтому прошу вашей помощи-подсказки!