DSM 6.2 Loader (with MBR partition Table)


Recommended Posts

Hi,

 

trying to use it on a dell wyse amd machine with 8111.

 

tried normal version 3615, 3617, 918 loaders en system is not found with 1.03b or 1.04.

 

To test i switched to 1.2b uefi system is found bit hangs in migratble status each time i finished. Tested after several attempt with 1.0b mbr genesys and finally i could complete the setup.

 

with triggered me to go for 1.3b mbr but now i get this error so confused

 

hemant

Link to post
Share on other sites
1 hour ago, Hemant13579 said:

trying to use it on a dell wyse amd machine

if you want to know 1.04b 918+ is even possible you would need to be more precise about the cpu

thats the thing to start with

https://xpenology.com/forum/topic/13333-tutorialreference-6x-loaders-and-platforms/

 

the thing about mbr is more does it boot or not, if you try a hp desktop with the normal gpt version its not booting at all and thats the point where you need mbr

if the normal version worked then the difference in success was not about mbr or gpt

1.03b cant  do clean uefi, it needs csm/legacy mode and you also need to use the non uefi usb boot device (that migh only be visible after booting once with csm on

just try the normal 1.03b version and make sure to have csm on and the right boot device

 

Link to post
Share on other sites

Hi IG-88,

 

CPU:  AMD G-T48E Processor

NIC; Realtek RTL8111E-VL/8111F GBE

 

When using 1.03b 3615 or 3617 i always lose the system after first install, after re-writing the image, it pops up as migratable but hangs there forever whatever I do to re-install.

 

Hemant

Link to post
Share on other sites
8 hours ago, hemant said:

When using 1.03b 3615 or 3617 i always lose the system after first install, after re-writing the image, it pops up as migratable but hangs there forever whatever I do to re-install.

i've had sometime problems when assigning a static ip address when installing, dhcp always worked so far

you can also try to use usb/disk combo on another system for installing and then take both back to your wyse system

Link to post
Share on other sites
3 hours ago, hemant said:

I'm running on DHCP, my other systems are HP with are MBR based

so then use the hp to prepare a usb/disk

just use the usb you intended for the whyse (match the usb's vid/pid in grub.cfg) disconnect alls disks and the hp's usb and use the new usb and a empty disk to intall

after you are done you copy off the grub.cfg from you new usb, rewrite it with the non mbr version of the loader and copy your tested grub.cfg back to that new non mbr version

that usb and the disk you prepared will hopefully boot on the whyse

Link to post
Share on other sites
  • 2 weeks later...

Thanks a ton for MBR version, my HP Z800 only boots up only on MBR version. That'll be great if we can have MBR version for DS3517XS.

Also one quick question, does this support DSM6.2.3 like Jun's loader?

Link to post
Share on other sites
  • 3 weeks later...
On 8/21/2019 at 11:06 AM, Big_11 said:

Hi Big_11

i habe a QNAP TS-269Pro and i need to install Synology DSM... i find your post and downloaded the file, while i have the same propblems as you had.

 

i downloaded your file, after installation and boot from UBS Stick I recevied the error:

erro: disk 'gpt1'  not found. 

Entering rescue mode...

grub rescue >..

and this is all, what is my mistakle or is the file not ready?

thanks in advance.

peppi

On 8/21/2019 at 11:06 AM, Big_11 said:

 

 

 

On 8/21/2019 at 11:06 AM, Big_11 said:

 

For those who need a MBR Bootloader for DSM 6.2 i've uploaded it here, if someone will give them a Chance...

i've successfully installed this on an Supermicro X7DBP-i with Intel Blackford 5000P Chipset.

It is a loader for the DSM6.2-23739.pat and can be directly upgraded to 6.2.2-24922 Update 2..

http://ul.to/zg58eusm

 

this loader is based on Jun's Mod of Genesys Loader and done with their help!...
Thanks a lot..

 

  Quote (Hide contents)

 

 

  • Confused 1
Link to post
Share on other sites
  • 3 weeks later...
  • 2 months later...
On 3/21/2021 at 10:10 AM, billat29 said:

Correct. As the messages at the top of the forum page say - 6.2.4 does not work right now

Any news to upgrade to dsm 6.2.4 with mbr loader?

Link to post
Share on other sites
  • 3 months later...

BRAVO and a very very big thank you Big_11 !!!
It worked wonderfully for an HP Z420 Workstation baremetal.

With :
XEON E5 1620 3,6Ghz 4 cores
+ Intel X550-T2 10Gbps NIC
+ SATA 3 88SE9239 PCIe v2 x4

The info center show : Intel Core i3-4130 3,6Ghz 2 cores, but anyway better that than nothing.

Small question :
is there any tutorial to learn how to transform Jun synoboot to MBR ?

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.