Hemant13579 Posted January 25, 2021 Share #26 Posted January 25, 2021 Hi, trying to use it on a dell wyse amd machine with 8111. tried normal version 3615, 3617, 918 loaders en system is not found with 1.03b or 1.04. To test i switched to 1.2b uefi system is found bit hangs in migratble status each time i finished. Tested after several attempt with 1.0b mbr genesys and finally i could complete the setup. with triggered me to go for 1.3b mbr but now i get this error so confused hemant Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 25, 2021 Share #27 Posted January 25, 2021 1 hour ago, Hemant13579 said: trying to use it on a dell wyse amd machine if you want to know 1.04b 918+ is even possible you would need to be more precise about the cpu thats the thing to start with https://xpenology.com/forum/topic/13333-tutorialreference-6x-loaders-and-platforms/ the thing about mbr is more does it boot or not, if you try a hp desktop with the normal gpt version its not booting at all and thats the point where you need mbr if the normal version worked then the difference in success was not about mbr or gpt 1.03b cant do clean uefi, it needs csm/legacy mode and you also need to use the non uefi usb boot device (that migh only be visible after booting once with csm on just try the normal 1.03b version and make sure to have csm on and the right boot device Quote Link to comment Share on other sites More sharing options...
hemant Posted January 26, 2021 Share #28 Posted January 26, 2021 Hi IG-88, CPU: AMD G-T48E Processor NIC; Realtek RTL8111E-VL/8111F GBE When using 1.03b 3615 or 3617 i always lose the system after first install, after re-writing the image, it pops up as migratable but hangs there forever whatever I do to re-install. Hemant Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 26, 2021 Share #29 Posted January 26, 2021 8 hours ago, hemant said: When using 1.03b 3615 or 3617 i always lose the system after first install, after re-writing the image, it pops up as migratable but hangs there forever whatever I do to re-install. i've had sometime problems when assigning a static ip address when installing, dhcp always worked so far you can also try to use usb/disk combo on another system for installing and then take both back to your wyse system Quote Link to comment Share on other sites More sharing options...
hemant Posted January 28, 2021 Share #30 Posted January 28, 2021 Hi, I'm running on DHCP, my other systems are HP with are MBR based Hemant Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 28, 2021 Share #31 Posted January 28, 2021 3 hours ago, hemant said: I'm running on DHCP, my other systems are HP with are MBR based so then use the hp to prepare a usb/disk just use the usb you intended for the whyse (match the usb's vid/pid in grub.cfg) disconnect alls disks and the hp's usb and use the new usb and a empty disk to intall after you are done you copy off the grub.cfg from you new usb, rewrite it with the non mbr version of the loader and copy your tested grub.cfg back to that new non mbr version that usb and the disk you prepared will hopefully boot on the whyse Quote Link to comment Share on other sites More sharing options...
AbuMoosa Posted February 9, 2021 Share #32 Posted February 9, 2021 Thanks a ton for MBR version, my HP Z800 only boots up only on MBR version. That'll be great if we can have MBR version for DS3517XS. Also one quick question, does this support DSM6.2.3 like Jun's loader? Quote Link to comment Share on other sites More sharing options...
peppi01 Posted March 1, 2021 Share #33 Posted March 1, 2021 On 8/21/2019 at 11:06 AM, Big_11 said: Hi Big_11 i habe a QNAP TS-269Pro and i need to install Synology DSM... i find your post and downloaded the file, while i have the same propblems as you had. i downloaded your file, after installation and boot from UBS Stick I recevied the error: erro: disk 'gpt1' not found. Entering rescue mode... grub rescue >.. and this is all, what is my mistakle or is the file not ready? thanks in advance. peppi On 8/21/2019 at 11:06 AM, Big_11 said: On 8/21/2019 at 11:06 AM, Big_11 said: For those who need a MBR Bootloader for DSM 6.2 i've uploaded it here, if someone will give them a Chance... i've successfully installed this on an Supermicro X7DBP-i with Intel Blackford 5000P Chipset. It is a loader for the DSM6.2-23739.pat and can be directly upgraded to 6.2.2-24922 Update 2..http://ul.to/zg58eusm this loader is based on Jun's Mod of Genesys Loader and done with their help!... Thanks a lot.. Quote (Hide contents) 1 Quote Link to comment Share on other sites More sharing options...
mufy Posted March 20, 2021 Share #34 Posted March 20, 2021 Hy all I tried this loader with 6.2.4 is not working. Quote Link to comment Share on other sites More sharing options...
billat29 Posted March 21, 2021 Share #35 Posted March 21, 2021 9 hours ago, mufy said: Hy all I tried this loader with 6.2.4 is not working. Correct. As the messages at the top of the forum page say - 6.2.4 does not work right now Quote Link to comment Share on other sites More sharing options...
mufy Posted June 10, 2021 Share #36 Posted June 10, 2021 On 3/21/2021 at 10:10 AM, billat29 said: Correct. As the messages at the top of the forum page say - 6.2.4 does not work right now Any news to upgrade to dsm 6.2.4 with mbr loader? Quote Link to comment Share on other sites More sharing options...
Dfds Posted June 10, 2021 Share #37 Posted June 10, 2021 3 hours ago, mufy said: Any news to upgrade to dsm 6.2.4 with mbr loader? 6.2.4 isn’t working with any loader at present. 1 Quote Link to comment Share on other sites More sharing options...
caltabpi Posted October 8, 2021 Share #38 Posted October 8, 2021 BRAVO and a very very big thank you Big_11 !!! It worked wonderfully for an HP Z420 Workstation baremetal. With : XEON E5 1620 3,6Ghz 4 cores + Intel X550-T2 10Gbps NIC + SATA 3 88SE9239 PCIe v2 x4 The info center show : Intel Core i3-4130 3,6Ghz 2 cores, but anyway better that than nothing. Small question : is there any tutorial to learn how to transform Jun synoboot to MBR ? Quote Link to comment Share on other sites More sharing options...
Big_11 Posted November 29, 2021 Author Share #39 Posted November 29, 2021 @caltabpi It's quiet easy, i think... You only have to create an Bootable USB Stick in MBR Format with the same parameters (VolSize) as seen in the image.. and then simply copy the content of the original Image to this partitions... Quote Link to comment Share on other sites More sharing options...
HermanCruz Posted December 3, 2021 Share #40 Posted December 3, 2021 Error Code 21 shows when upgrading DS3617sx 6.2.3-25426 to 6.2.4-25556 Please help Quote Link to comment Share on other sites More sharing options...
billat29 Posted December 4, 2021 Share #41 Posted December 4, 2021 As you will have found when you came here, 6.2.4 is NOT supported by the current loaders (There is a new one in development but it's not ready yet). You will need to do this.... Quote Link to comment Share on other sites More sharing options...
Big_11 Posted December 4, 2021 Author Share #42 Posted December 4, 2021 (edited) 11 hours ago, HermanCruz said: Error Code 21 shows when upgrading DS3617sx 6.2.3-25426 to 6.2.4-25556 Please help as @billat29 posted before... i'm pretty sure that 6.2.4-xxx is not supported by this loader (anyway if MBR or GPT)... @HermanCruzpls read carefully the Attentions at the top if this forum !! espacially this "Critical Update READ ME topic - IMPORTANT - XPEnology Community" Edited December 4, 2021 by Big_11 Quote Link to comment Share on other sites More sharing options...
Flashmarion Posted February 17, 2022 Share #43 Posted February 17, 2022 Need help. Have the motherboard MSI Z590-a PRO, intel i3 10105f. Use the all loader but the NAS is not find in network (synology assistant not find it) Quote Link to comment Share on other sites More sharing options...
IG-88 Posted February 17, 2022 Share #44 Posted February 17, 2022 (edited) 14 hours ago, Flashmarion said: Have the motherboard MSI Z590-a PRO, intel i3 10105f. Use the all loader but the NAS is not find in network (synology assistant not find it) spec say's "1x Intel® I225-V 2.5Gbps LAN" the driver for that is only build into kernel 5.x and intel does not intent do make a standalone driver for older kernels (like 3.10/4.4 as synology uses) (the driver would be igc.ko) use a realtek 2.5G nic if it has to be 2.5G or any usual intel 1G nic (realtek 8168/8111 will work too) Edited February 17, 2022 by IG-88 Quote Link to comment Share on other sites More sharing options...
ikannuna Posted February 21, 2022 Share #45 Posted February 21, 2022 On 1/3/2020 at 3:06 AM, Manti said: Thank you! Worked on a hp dc7900 with DSM 6.2.2 I have a HP DC7900 and I cannot get the OS to install properly, after install it prompts me to migrate and I only have one disk installed and it's blank. Then if I go ahead and migrate re-installing the OS it just reboot and then nothing, it's not found on the network however it loads from the USB as normal. Can you share your BIOS settings and USB drive setup? Thanks Quote Link to comment Share on other sites More sharing options...
hemant Posted February 21, 2022 Share #46 Posted February 21, 2022 27 minutes ago, ikannuna said: I have a HP DC7900 and I cannot get the OS to install properly, after install it prompts me to migrate and I only have one disk installed and it's blank. Then if I go ahead and migrate re-installing the OS it just reboot and then nothing, it's not found on the network however it loads from the USB as normal. Can you share your BIOS settings and USB drive setup? Thanks Hi Did you user the MBR version for HP models, i do recall I had to use the MBR one for HP which worked. Also de bios is set to legacy boot. I used the 3615 image for that box. and you need to make use your MAC address is correct. Hemant Quote Link to comment Share on other sites More sharing options...
IG-88 Posted February 21, 2022 Share #47 Posted February 21, 2022 10 hours ago, hemant said: Hi Did you user the MBR version for HP models, i do recall I had to use the MBR one for HP which worked. Also de bios is set to legacy boot. for that desktop model for sure disable secure boot, enable csm/legacy and boot from usb legacy device (F9 on boot, its also possible to disable uefi boot completly in bios on the section where the boot order is set) 10 hours ago, hemant said: I used the 3615 image for that box. and you need to make use your MAC address is correct. the mac is more about convenience (same mac in network when dsm is running as seen in bios or seen when a normal os is booted) or if you want to use WOL Quote Link to comment Share on other sites More sharing options...
cRsv6EOUS Posted September 17, 2022 Share #48 Posted September 17, 2022 Guys , advise please MBR loader for 6.2 (to upgrade from 6.1.7) with Intel 82579LM Gigabit Network Connection Quote Link to comment Share on other sites More sharing options...
helldarkmonster Posted January 25 Share #49 Posted January 25 Link is dead is it possible to reupload. Thanks Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.