brunobf Posted June 7, 2014 Share #51 Posted June 7, 2014 I've installed 4493 on my HP N54L. Everything went fine except for logging in. Message: System is getting ready. Please try again in a few moments. Got ssh access etc... just not logging in in GUI. EDIT: SOLVED! Turns out MariaDB service was hanging. I think upgrading from trantor to gnoboot to nanoboot had something to do with it because clean installs work fine. Hey Poechi, How did you diagnose which service was hanging? I'm new to Synology and couldn't find anything in the message log. I was able to fully boot the system with: "synobootseq --set-boot-done" But I suppose that it might get stuck every time I boot. Thanks Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 7, 2014 Share #52 Posted June 7, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
brunobf Posted June 8, 2014 Share #53 Posted June 8, 2014 I couldn't find anything that looked suspicious on my system, so I did the following: Moved every folder from /var/packages/ to a temporary directory. I didn't know of any other way to actually disable all the services in the DSM. After that the unit rebooted fine. So I then manually moved the services back one by one, and rebooted each time. My problem was with the debian-chroot package from Synocommunity. Apparently when I added a debian service to be initialized along with the system, it caused DSM to hang. Maybe I have to end the startup command with &. Thanks, Bruno Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 8, 2014 Share #54 Posted June 8, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
ema Posted June 8, 2014 Share #55 Posted June 8, 2014 Well I can create blocklevel but connection is not working through iSCSI initiator Windows. Maybe I'm doing something wrong. No, it's not your fault, simply block level it's not working like in previous version (gnoboot, nanoboot)... they switched from IET to LIO... From http://xpenology.com/forum/viewtopic.php?f=2&t=2152 >> Fixed - Broken block-level iSCSI (LIO), workaround enable IET in synoinfo.conf Thanks! ema Did you got it working with IET mode? No... I use it only in file level mode. Quote Link to comment Share on other sites More sharing options...
gsxr Posted June 8, 2014 Share #56 Posted June 8, 2014 upgrade from 4482 worked no problems Quote Link to comment Share on other sites More sharing options...
Mokai Posted June 8, 2014 Share #57 Posted June 8, 2014 upgrade from 4482 worked no problems Can you tell us what boot you are using and how do you run that upgrade? Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 8, 2014 Share #58 Posted June 8, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 8, 2014 Share #59 Posted June 8, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
Muaddib Posted June 8, 2014 Share #60 Posted June 8, 2014 Do I have to make the 5.0-4493 upgrade from the upgrade menu on the NaoBoot? Or is it posible to do is with the DSM update function in Synology? Tha last thing does not seem to Work for me on my HP H40L. It starts and then hangs on the 1% circle thing.... Quote Link to comment Share on other sites More sharing options...
Spooky1 Posted June 9, 2014 Share #61 Posted June 9, 2014 Do I have to make the 5.0-4493 upgrade from the upgrade menu on the NaoBoot? yes Or is it posible to do is with the DSM update function in Synology? no Quote Link to comment Share on other sites More sharing options...
Muaddib Posted June 9, 2014 Share #62 Posted June 9, 2014 Do I have to make the 5.0-4493 upgrade from the upgrade menu on the NaoBoot? yes Or is it posible to do is with the DSM update function in Synology? no Damn. Would have been so much easier. Now I have to find a monitor and a keyboard too connect to the box... Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 9, 2014 Share #63 Posted June 9, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
Freezer Posted June 10, 2014 Share #64 Posted June 10, 2014 Dear all, im was running DSM 5.0-4482 with nanoboot on my ESXI. I have three Disks: 1. IDE with VMDK Nanoboot 2. 16GB for System 3. 2TB RAW Device Map But i decided to Upgrade to 4493. So this were the steps: I uploaded the new Boot VMDK, deleted the old one, attached the new one as IDE. During boot i choose "Install/Upgrade". I followed the instructions on the Web Gui and uploaded the 4493 PAT File (original from Synology) to "migrate". During the Upload my Computer(Laptop) is getting a "Bluescreen" so I think the Upload was not complete. Very strange my Thinkpad T530 is never getting a Bluescreen before So I restarted the VM, and started the Upload a second time. At 55% it stucks with "unknown ecception". Than i tested to use my old existing 4482 VMDK to boot (to look if it works) --> It works Than i attached again the 4493 VMDK and booted it normaly. --> It also works. Also my GUI says that i am on Version 4493, but i'm not shure if this is true. Any way to check the "true" version that is currently running? Any advises what I should do now? Other Question: Is it possible to reinstall the whole System without deleating mit 2TB drive? Very happy if i can get Help Quote Link to comment Share on other sites More sharing options...
djelusion Posted June 10, 2014 Share #65 Posted June 10, 2014 i cant even get 4482 on my system and then theres this update.. fuck me...... Quote Link to comment Share on other sites More sharing options...
davurleon Posted June 10, 2014 Share #66 Posted June 10, 2014 Oh come on, do you think we are cheap on this forum or what??? Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 11, 2014 Share #67 Posted June 11, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
yabba235 Posted June 11, 2014 Share #68 Posted June 11, 2014 Update 1 installing with no problems Quote Link to comment Share on other sites More sharing options...
chrishunter01 Posted June 11, 2014 Share #69 Posted June 11, 2014 Updated directly from the site.... without any hitch.... DSM 5.0-4493 update 1.tiff Quote Link to comment Share on other sites More sharing options...
Freezer Posted June 11, 2014 Share #70 Posted June 11, 2014 Currently running DSM 5.0-4493, whats the best way to get to Update 1 ? Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 11, 2014 Share #71 Posted June 11, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
sancome Posted June 12, 2014 Share #72 Posted June 12, 2014 Currently running DSM 5.0-4493, whats the best way to get to Update 1 ? Installation instruction: http://www.xpenology.nl/installatie-dsm ... -update-1/ Also I've placed the new Nanoboot boot image version 5.0.3.1 here, http://www.xpenology.nl/boot-images/. I don't mind you available for download, but please Indicate the source http://nanoboot.tk Quote Link to comment Share on other sites More sharing options...
phoenix73 Posted June 12, 2014 Share #73 Posted June 12, 2014 I restarted my nl54 with nanoboot 5.0.2.4 (4493). I was still in 4458-u2. When connected to the web UI, i could see users, settings and volume1 reported same Free Space but DSM reported no share. Folders and files didn't show in file station. Connected via ssh, doing ls in volume1 failed with error message "invalid adress". I rebooter with gnoboot and contents was back again. Any idea of what could be wrong with nanoboot ? I should add my volume is in degraded mode, disk 1 was faulty and removed, system works on disk 2. Thanks for your advices Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Poechi Posted June 12, 2014 Share #74 Posted June 12, 2014 (edited) - Edited July 10, 2015 by Guest Quote Link to comment Share on other sites More sharing options...
phoenix73 Posted June 12, 2014 Share #75 Posted June 12, 2014 Anyone got volume1 contents disapearing when switching boot key from gnoboot to nanoboot (5.0.2.4) ? I use NL nanoboot and only updated SN. Everything went back after rebooting with gnoboot hopefully Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.