Jump to content
XPEnology Community

DSM 6.2.2-24922


Flotho
Message added by Polanskiman

Please read the READ ME topic before posting:

 

Recommended Posts

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.03b - DS3615

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.7u2 with LSI 9211-8 on Dell T30

- Additional comments: Reboot required, vNICs had been E1000e before, so problem at all. Addition vmdk on SATA1:0 was missing as synoinfo.cfg was replaced by a default file. This time I fixed it permanently by setting DiskIdxMap in the grub.cfg, so it won't become a problem on the next major or minor update.

 

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.03b - DS3615

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.7u2 on Dell T30

- Additional comments: Reboot required, vNICs had been E1000e before, so problem at all.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.7u2 on Supermicro X9SRH

- Additional comments: Reboot required, all disks as RDM on 2nd SATA controller.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.7u2 on Supermicro X11SPM

- Additional comments: Manual update, reboot. Disk as VMDK on VMware Paravirtual SCSI controller.

Edited by fafner
Link to comment
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824U6

- Loader version and model: Jun's loader v1.03b, DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  HP MicroServer Gen10

- Additional comments: Internal NIC disabled, added a HP NC360T dual port NIC.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 6

- Loader version and model: Jun's loader v1.03b, DS3615xs

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.7 U2 13473784 on Microserver Gen8

- Additional comments: Dell H200 @LSI Controller in passthrough, NIC set to e1000e.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Gen8 Microserver

- Additional comment: internal NIC disabled and compatible Intel PCIe NIC installed

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.2-24922

- Loader version and model: Jun v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: ASRock Z370M-ITXac (built-in WiFi card removed) + i3-8100T

- Additional comments: reboot by itself

Link to comment
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 6

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver Gen 8 with Intel NIC (restart by Manual)

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Gen8 Microserver

- Additional comment: Internal NIC disabled, added a HP NC360T dual port NIC.

Link to comment
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM v6.2-23739-2

- Loader version and model: Jun Loader v1.03b - DS3615

- Using custom extra.lzma: NO

- Installation type: VM - Proxmox 5.4-3 (HP GEN8 G1610T)

- Additional comments: Changed LAN from e1000 to e1000e

Link to comment
Share on other sites

Outcome of the update: SUCCESSFUL
- DSM version prior update: New VM (no prior installation). Running DS918+_6.2.2-24922
- Loader version and model: Jun's Loader v1.04b - DS918+
- Using custom extra.lzma: NO
- Installation type: VM - Virtual box - Test setup on a 2015 MacBookPro 2.2 GHz i7, Intel Iris Pro 1536MB
- Additional comments: Had to use the following network mac address to connect to web gui: 001132123456

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL
- DSM version prior update: DSM 6.2.1-23824U6
- Loader version and model: Jun's Loader v1.04b DS918+
- Using custom extra.lzma: NO
- Installation type: VM - ESXi 6.7u2 with LSI 9211-8, E1000e
- Additional comments: Reboot required, bootloader modified sata_arg, no modification on synoinfo.cfg.

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J4105-ITX

Link to comment
Share on other sites

- Outcome of the update: FAILED
- DSM version prior update: DSM v6.2-23739
- Loader version and model: Jun Loader v1.03b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: VM - VMware Workstation 14.0
- Additional comments: No auto reboot during update via GUI. No boot to DSM both console and GUI after manual reboot(reset)

 

- Outcome of the installation: FAILED
- DSM version prior update: new Installation DSM_DS3615xs_24922.pat
- Loader version and model: Jun Loader v1.03b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: VM - VMware Workstation 14.0
- Additional comments: No auto reboot during install via GUI. No boot to DSM both console and GUI after manual reboot(reset)

Link to comment
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.2-24922

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  ASRock H270M-ITX/ac

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.7 UPDATE 3 - JUN'S LOADER v1.02b DS3615xs
- Loader version and model: JUN'S LOADER v1.03b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - HP Compaq Elite 8300 SFF , integrated Intel 82579LM NIC

- Additional comments: JUN'S LOADER v1.03b Hybrid partition table usb key created, UEFI boot disabled in BIOS

Link to comment
Share on other sites

- Outcome of the update: FAILED (if no monitor connected)

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J4105-ITX

- Additional comments: I should say the 6.2.2 is working only if my VGA monitor is connected (regardless if it's power on/off). No HW transcoding available in 6.2.2 in this case. If moditor is disconnected, DSM won't start.

 

 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

- Outcome of the install: FAILED

- DSM version prior to update: DSM 6.2.1-23824 U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - e3-1220v3 / 16GB / LSI 9220-8i IT 

- Additional comments: Error 13 when attempting to install to test HDD "multiple USB drives used with correct VID/PID, multiple test drives, two S/N"

 

- Outcome of the update: FAILED

- DSM version prior to update: DSM 6.2.1-23824 U6

- Loader version and model: Jun Loader v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - e3-1220v3 / 16GB / LSI 9220-8i IT

- Additional comments: Upgraded to 6.2.2 but no ping after reboot

 

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.2-224922

- Loader version and model: Jun Loader v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - e3-1220v3 / 16GB / LSI 9220-8i IT

- Additional comments: After changing to DS3615xs loader, install detected the DS3617xs installation and migrated successfully

Link to comment
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - DELL Optiplex 3020 i3-4160, 4G DDR3 1600MHz, 1TB 7200RPM
- Additional comment: boot with udisk

Link to comment
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 6

- Loader version and model: Jun v1.03b - DS3615

- Using custom extra.lzma: NO

- Installation type: VM - Proxmox 5.4-3

- Additional comments: Changed LAN from e1000 to e1000e

Link to comment
Share on other sites

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte B75M-D3H - Intel E3-1245v2 - Mellanox ConnectX-2 MNPA19-XTR

- Additional comments: No internet after upgrade.

 

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte B75M-D3H - Intel E3-1245v2 - Intel X520-T2

- Additional comments: No internet after upgrade.

 

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte B75M-D3H - Intel E3-1245v2 - Mellanox ConnectX-3 MCX311A-XCAT

- Additional comments: No internet after upgrade.

 

- Outcome of the install: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte B75M-D3H - Intel E3-1245v2 - Mellanox ConnectX-3 MCX311A-XCAT

- Additional comments: Change the loader to DS3615xs and migrate from DS3617xs

 

Link to comment
Share on other sites

- Outcome of the update: FAILED

- DSM version prior to update: DSM 6.2.1-23824U6

- Loader version and model: Jun v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J3160-ITX

Link to comment
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 update 6

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J3455

- Additional comments: Onboard lan not tested, all ok with PCIE Intel NIC.

Link to comment
Share on other sites

 

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 update 6

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Supermicro X10SL7-F-0 with both SATA (6 ports) and SAS (8 ports - LSI2308) and dual onboard Intel (i210AT) NICs.

- Additional comments: fastest System update ever; seems to be operating normally; also updated several of the apps that were showing as outdated.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...