Polanskiman

Please read the READ ME topic before posting:

 

Message added by Polanskiman

Recommended Posts

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: New Installation

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  HP Microserver GEN8 + HP NC360T

- Additional comments:  ACPI BIOS configured and disable internal NIC; restart + shutdown  OK;

  • Like 1

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: New Installation

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs (previously with internal NIC only I was running DS3617xs 6.17-15284 U3 using v1.02b)

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  HP Microserver Gen 7 N54L + HP NC360T (NIC)

- Additional comments:  Disabled internal NIC & added NC360T NIC then new install using v1.03b and single "sacrificial" disk + shutdown  OK; then added back 4 disks with data on - DSM complained system partitions failed & rebuilt successfully.

Share this post


Link to post
Share on other sites

 Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 update 2

- Loader version and model: Jun 1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J1900-ITX

- Additional comments: NONE

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2 1.03b - ds3617xs

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  Gigabyte GA-970a-ds3p AMD FX-4300

- Additional comments: Original install was using 1.03b ds3617xs tried to update using same loader but would not load at all.  It would hang right after the menu selection screen.  Downgraded to 6.1.7 DS3617xs then migrated to 6.2.1-23824 update 4 DS3615xs and it worked.  Onboard realtek nic no longer works but extra HP NC-360t dual port Intel NIC works fine.  Long story short for anyone else using AMD make sure you are using the DS3615xs loader boot as none of the others work.  I tried DS918+ 1.04b and DS3617xs 1.03b and neither worked using Legacy or UEFI boot.

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.1.7-15284 Update 3

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock Q1900-ITX

- Additional comments: easily migrated my 6x4To RAID6 drives from jun's v1.02b DS3615XS to v1.04b DS918+ without hassles, just had to install new Power Button package.

  • Like 1

Share this post


Link to post
Share on other sites

- Outcome of the Installation: SUCCESSFUL

- DSM version prior update: Fresh Installation

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASROCK Z390M-ITX/AC, Intel Core i7 8700, 16GB RAM on U-NAS 410 Chassis with Noctua NH-L9i CPU fan

- Additional comments: Only one NIC works

Share this post


Link to post
Share on other sites

- Outcome of the update:  SUCCESSFUL

- DSM version prior update: DSM 6.1.7

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -  HP G7 N54L  

- Additional comments: restart + shutdown  OK / ADD NIC HP NC360T, disable internal NIC, delete .xpenology/ folder old loader.

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 2

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - MSI H310I PRO, Intel Pentium Gold G5400, onboard LAN Realtek

 

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 update 1

- Loader version and model: JUN'S LOADER v1.04b - DS918+

-  Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP MicroServer Gen10 with AMD Opteron X3216

- Additional comments: HP NC360T Dual NIC, Boot from external USB Socket necessary, NVMe SSD not working

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.1.7-15284 Update 3

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asus AM1I-A - AMD 5350 + 8GB Ram

- Additional comments: add "disable_mtrr_trim" to grub.cfg

  • Thanks 1

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: Fresh install

- Loader version and model: JUN'S LOADER v1.04b - 918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J5005

- Additional comments: 0 problems

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.1.7-15284 Update 3

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: VM - MWARE ESXI 6.5U1 -  on Dell Poweredge R710

- Additional comments: Reboot needed + NIC set to E1000e

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: Jun's Loader v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: VM - ESXi 6.5U2 on Microserver Gen8

- Additional comments: Cougar Point 6 port SATA AHCI Controller in passthrough, NIC set to e1000e.

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: Jun's Loader v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J3355m, 8GB RAM

- Additional comments:

  • NIC: Intel Pro1000 CT (EXPI9301CT), works out of the box.
  • SATA Controller: Highpoint Rocket 640L (4x SATA, Marvell 88SE9230). Sata controller needs flash! Without flash raid sets crash and system is not stable.  (same problem on <DSM 6.2) With latest firmware from Digitus the DMESG errors disappear and system is very stable and fast. Digitus firmware for 88SE9230 (use freedos usb stick to flash)
  • I also use SataPortMap=24 in GRUB to make my disks appear as disk 1-6. (onboard first)
  • This is brand new cheap and fast system supporting max 6 disks and using <50W power on load.

 

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: Fresh install of DSM 6.2.1-23824 Update 4

- Loader version and model: JUN'S LOADER v1.04b - 918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J3455M

- Additional comments:

  • 9 x 8TB (Raid 5)
  • x3 of IO Crest 4 Port SATA III PCI-e 2.0 x1 Controller Card Marvell Non-Raid with Low Profile Bracket SI-PEX40064
  • Onboard LAN
  • No other amendments made
  • QuickConnect service tested and not working (perhaps due to carry over S/N and MAC used from previous DSM 6.0.1 Baremetal installation)

Share this post


Link to post
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.2.-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver Gen 8 with Intel NIC(restart by Manual)

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: Fresh Install

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J5005

Share this post


Link to post
Share on other sites

-Outcome of the migration: SUCCESSFUL
-DSM version prior update: N/A

-Loader version and model: Jun's Loader v1.04b - DS918+
-Using custom extra.lzma: NO

- Installation type: BAREMETAL Dell PowerEdge T20 Xeon E3-1225 V3 
- Additional comments:  I was running Jun's Loader v1.03b - DS3615xs on my HP Gen8, I decided to upgrade, so I got a Dell PowerEdge T20 server, so I migrated my data and settings from Jun's Loader v1.03b - DS3615xs to DS918+ using 1.04b loader. The on-board NIC works out but I ran into some errors while migrating. I kept getting "Failed to install the file. The file is probably corrupted. (13 )" until I upgraded Dell T20's BIOS, then using UEFI and sata sets to AHCI mode. 

 

 

Edited by Polanskiman
User did not provide DSM version instead he mentioned: "Jun's Loader v1.03b - DS3615xs (Running on HP Gen8)"

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs to DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Motherboard: Acer FSB 1333 Q45T-AM v:1.0 | CPU: INTEL Core i3-4130|  RAM: 5120 MB

- Additional comments: Following are the steps I have implemented to upgrade from model DS3617xs with version 6.2-23739 to DS3615xs with version 6.2.1-23824 update 4:

  • old hard drive there on DS3617xs with version 6.2-23739 stop the PC. install DS3615xs on usb reboot install version 6.2-23739 for DS3615xs. test whether everything has been saved. update to 6.2.1-23824 update 4 (test data was saved.)
  • Turn off the PC. connect disks with data to start pc install Version 6.2.1-23824 update 4 for the DS3615xs. everything work!
  • UPDATE
  • From af DS3617xs to update 6.2.1-23824 does not work !!! 
  • Test it first with a spare drive I recommend.

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Motherboard: Acer FSB 1333 Q45T-AM v:1.0 | CPU: Intel Xeon D-1527|  RAM: 5120 MB

- Additional comments:  From af DS3617xs to update 6.2.1-23824 does not work !!!  Test it first with a spare drive I recommend.

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 update 1

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - i3 8100, ASUS PRIME H310-PLUS, 8GB RAM

- Additional comments: Bios - UEFI

  • NIC: Internal Realtek RTL8111H + Intel Pro PWLA8391GTL (PCI) works out of the box.
  • SATA Controller: Dell PERC H200 crossflashed to LSI 9211-i8 works out of the box.
  • Restart + Shutdown  OK
  • SW+HW transcoding OK

Share this post


Link to post
Share on other sites

-Outcome of the update : SUCCESSFULL

-DMS version prior update :DSM 6.2.1-23739

-Loader version and model :Jun's loader V1.03b -DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL -AMD A6, gigabyte GA-A55m , 4GB RAM

- Additional comments:

  • NIC : HP NC360T internal nic desactived
  • SATA Controller: Internal sata A75 chipset
  • Restart+ Shutdown :OK

 

Share this post


Link to post
Share on other sites

-Outcome of the update: SUCCESSFULL
-DMS version prior update: DSM 6.2.1-23739
-Loader version and model: Jun's loader V1.03b -DS3615xs
- Using custom extra.lzma: NO
- Installation type: BAREMETAL - N54L
- Additional comments:

  • NIC : HP NC360T internal nic deactivated
  • USB3: uPD720202 not recognize any connected device
  • Restart+ Shutdown: OK

Share this post


Link to post
Share on other sites

- Outcome of the installation/update:  SUCCESSFUL

- DSM version prior update: DSM 6.1.7U4 --> DSM 6.2.-23739 Update 1

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HP Microserver Gen 8 with Intel E1G42ET NIC

- Additional comments : Powerbutton OK, phpvirtualbox 5.2.20 OK, Shutdown+restart OK

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL
- DSM version prior update: DSM 6.1.7 UPDATE 1
- Loader version and model: JUN'S LOADER v1.03b - DS3615xs
- Using custom extra.lzma: NO
- Installation type: HP Elite 8200, integrated NIC Intel 82579LM

- Additional comments:

  • Computer needs to be booted in Legacy BIOS mode for network to work. However HP Elite 8200 UEFI BIOS refuses to boot loader in Legacy mode, only EFI. To solve this issue I converted USB key's partition table from Protected to Hybrid partition table. That helped BIOS to see MBR partitions and boot in Legacy mode.
  • Before upgrade the computer was booted with loader 1.03b. Then DSM 6.2.1 was installed, starting web page find.sysnology.com (as a new install would be made).

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.