Polanskiman

Please read the READ ME topic before posting:

 

Message added by Polanskiman

Recommended Posts

- Outcome of the update: SUCCESSFUL

- DSM version prior update: Fresh install on Proxmox 5.2.8

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: VM - KVM

- Additional comments: Used Intel E1000 NIC

  • Like 1

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: Fresh install of DSM 6.2.1-23824 -> Update 1

- Loader version and model: Jun's LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - SuperMicro X11SSH-LN4F + i3 6300 + 16Gb ECC + 1 Dell Perc H310 IT mode.

- Additional comments:

  • 8HDD in H310 & 2 SSD in MB detected and working properly (16 disks oob 😲)
  • 4 NIC´s working after modifying synoinfo.conf.
  • /dev/dri finally showed up😊
  • Plex & Video Station trascode crashes the system after some seconds 😢 (without trascoding it plays perfectly).
  • Shutdown and reboot working (It was not possible with 1.03a2).
  • UEFI boot

 

  • Thanks 1

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23729 (Fresh Install)

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Dell Optiplex 7020 MT

- Additional comments: Manual reboot didn't fix either. Intel I217LM onboard nic never grabs an IP from dhcp.

Share this post


Link to post
Share on other sites

- Outcome of a fresh install: SUCCESSFUL

- DSM version DSM 6.2.1: Fresh install on a N4200 Apollo Lake using VMware Workstation 14

- Loader version and model: Jun's Loader v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: VM 

- Additional comments: Used standard VMware NIC, SATA for boot and SCSI for DSM installation (disk1)

 

 

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: Fresh install of DSM 6.2.1-23824 -> Update 1

- Loader version and model: Jun's LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Intel G4560 on a MSI B250-i Pro motherboard. It uses ethernet adapter: Realtek RTL8111H  

- Additional comments: Used the Xpenology tool found on the forum for mostly everything and just following the tutorial: install/migrate DSM 5.2 to 6.1.x (Jun's loader). 

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2 - DS3617xs

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J1900DC-ITX

- Additional comments: None

 

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: Fresh Install

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J3455-ITX 

- Additional comments: None

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: Fresh install

- Loader version and model: Jun's Loader v1.03b DS3615xs

- Using custom extra.lzma: No

- Installation type: BAREMETAL - QNAP 459 Pro 

- Additional comments: Installed DSM 6.2.1-23824 Update 1

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: Reinstalled DSM 6.2-23739 Update 2 over the top after upgrade failure from 6.1.7

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Gigabyte ga-h97n-wifi

- Additional comments: As previously mentioned. On-board NIC Atheros no longer works after this update. On-board NIC Intel works OK (I have popped in a dual port intel gigabit card to retain link aggregation).

 

Everything else seems to be working, except for the fact I cannot actually restart or shutdown the NAS. When issuing a restart or shutdown, DSM and all network connectivity is lost, except ICMP still respond pings. NAS is no longer visible on Synology Assist. I am forced to hard shutoff the NAS and power on again to restart.

 

Overall I required major troubleshooting to get my upgrade from 6.17 to 6.2 to work.

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J4205-ITX

- Additional comments: Clean install with 2x 4TB WD RED drives using SATA:0 and SATA:1 ports.

After the installation, the system rebooted, the countdown started from 10:00. I waited 15 minutes, then I tried to access it from my browser using the static IP address I assigned from my router. Always got request timed out.

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - (Asrock D1800M)

- Additional comments: NONE

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Lenovo LS140 onboard Intel [type] I217LM NIC

- Additional comments: NONE

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 update 2

- Loader version and model: JUN'S LOADER v1.04 - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - Asrock J3455M

- Additional comments: Baremetal install onto clean drive / 4 port SATA card also installed. Update fails at 2% with Unknown Error(21)

Edited by Polanskiman

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J5005-ITX - 16GB RAM

- Additional comments: NONE

Share this post


Link to post
Share on other sites

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.1.6-15266-1

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: No

- Installation type: ESXi on HP Microserver G10

- Additional comments: Upgraded from 6.1.x with loader v1.02b to latest 6.2 with v1.03b

Configured system with an extra Sata controller, put Jun's loader on 0:0 and my pass-through disks on SATA 1:X, just to be sure

Set Network card to E1000e prior to upgrade. I could not get the VMNET 3 adapter working after installing Open-VMware Tools, so reverted back to the E1000e type.

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739 Update 2

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: Baremetal - HP Microserver GEN 8

- Additional comments: with internal nic and hP NC360T

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23729

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - m5 + HD 300Go SSD + RAM 4 Go

- Additional comments:  deadly crach

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - asrock FM2A75 PRO4-M

- Additional comments: None

Share this post


Link to post
Share on other sites
Posted (edited)

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23729 (fresh install)

- Loader version and model: JUN'S LOADER v1.03b - DS3617xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - HPE Microserver Gen8 w/G1610T cpu

- Additional comments: kernel panic, see serial dump below

 

Spoiler

[    0.011821] [Firmware Bug]: the BIOS has corrupted hw-PMU resources (MSR 38d is 330)
[    1.943657] I/O scheduler elevator not found
[    2.412371] I/O scheduler elevator not found
patching file etc/rc
patching file etc/synoinfo.conf
Hunk #1 FAILED at 261.
1 out of 1 hunk FAILED -- saving rejects to file etc/synoinfo.conf.rej
patching file linuxrc.syno
Hunk #3 succeeded at 552 (offset 1 line).
patching file usr/sbin/init.post
cat: can't open '/etc/synoinfo_override.conf': No such file or directory
START /linuxrc.syno
Insert Marvell 1475 SATA controller driver
Insert basic USB modules...
:: Loading module usb-common ... [  OK  ]
:: Loading module usbcore ... [  OK  ]
:: Loading module ehci-hcd ... [  OK  ]
:: Loading module ehci-pci[    3.736779] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[    3.773694] BUG: unable to handle kernel paging request at ffff880105b34f20
[    3.807416] IP: [<ffff880105b34f20>] 0xffff880105b34f1f
[    3.832666] PGD 1ac2067 PUD 1ac5067 PMD 8000000105a000e3
[    3.858394] Oops: 0011 [#1] SMP
[    3.874197] Modules linked in: ehci_pci(F+) ehci_hcd(F) usbcore usb_common mv14xx(O) brmzpp(OF)
[    3.916353] CPU: 0 PID: 3446 Comm: insmod Tainted: GF          O 3.10.105 #23824
[    3.951825] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 11/02/2015
[    3.986306] task: ffff8801059aa800 ti: ffff880101cd4000 task.ti: ffff880101cd4000
[    4.022428] RIP: 0010:[<ffff880105b34f20>]  [<ffff880105b34f20>] 0xffff880105b34f1f
[    4.060094] RSP: 0018:ffff880101cd7b78  EFLAGS: 00010046
[    4.086331] RAX: ffff880105b39410 RBX: 0000000000000006 RCX: 0000000000000002
[    4.121882] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff8801058cc000
[    4.156487] RBP: ffff8801058cc000 R08: ffff880101cd7b84 R09: 000000000000fffb
[    4.191285] R10: 0000000000000000 R11: 0000000000000275 R12: 0000000000000000
[    4.225869] R13: ffff880101cd7bbe R14: 0000000000000246 R15: ffffffffa00ebb40
[    4.260056] FS:  00007f677f845700(0000) GS:ffff88010ba00000(0000) knlGS:0000000000000000
[    4.299936] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    4.327781] CR2: ffff880105b34f20 CR3: 0000000101702000 CR4: 00000000001607f0
[    4.362851] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[    4.396945] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[    4.431806] Stack:
[    4.441285]  ffffffff81292f25 0000000001cd7bd8 0000000000000010 000000000000000a
[    4.476966]  ffff8801058cf7f8 0000000000000000 ffff8801058cf890 ffffffff81298046
[    4.512208]  0000000000000001 ffff8801058cf7f8 ffffffff8129808b ffff88010178d000
[    4.547817] Call Trace:
[    4.559432]  [<ffffffff81292f25>] ? pci_bus_read_config_word+0x65/0x90
[    4.591473]  [<ffffffff81298046>] ? __pci_bus_find_cap_start+0x16/0x40
[    4.623403]  [<ffffffff8129808b>] ? pci_find_capability+0x1b/0x50
[    4.653736]  [<ffffffffa00eb09d>] ? ehci_pci_setup+0x9d/0x5a0 [ehci_pci]
[    4.685812]  [<ffffffffa00aac4d>] ? usb_add_hcd+0x1bd/0x660 [usbcore]
[    4.717500]  [<ffffffffa00b99d3>] ? usb_hcd_pci_probe+0x363/0x410 [usbcore]
[    4.750684]  [<ffffffff8129bd80>] ? pci_device_probe+0x60/0xa0
[    4.779521]  [<ffffffff8130575a>] ? really_probe+0x5a/0x220
[    4.806324]  [<ffffffff813059e1>] ? __driver_attach+0x81/0x90
[    4.834621]  [<ffffffff81305960>] ? __device_attach+0x40/0x40
[    4.862413]  [<ffffffff81303a53>] ? bus_for_each_dev+0x53/0x90
[    4.891237]  [<ffffffff81304ef8>] ? bus_add_driver+0x158/0x250
[    4.919256]  [<ffffffffa00ed000>] ? 0xffffffffa00ecfff
[    4.944448]  [<ffffffff81305fe8>] ? driver_register+0x68/0x150
[    4.972961]  [<ffffffffa00ed000>] ? 0xffffffffa00ecfff
[    4.998292]  [<ffffffff810003aa>] ? do_one_initcall+0xea/0x140
[    5.026608]  [<ffffffff8108baf4>] ? load_module+0x1a04/0x2120
[    5.054419]  [<ffffffff81088cb0>] ? store_uevent+0x40/0x40
[    5.081174]  [<ffffffff8108c2a1>] ? SYSC_init_module+0x91/0xc0
[    5.110014]  [<ffffffff814c0dc4>] ? system_call_fastpath+0x22/0x27
[    5.139888] Code: 00 00 00 00 00 00 00 00 00 00 00 20 13 b3 05 01 88 ff ff 60 18 b3 05 01 88 ff ff e0 58 a2 05 01 88 ff ff 00 00 00 00 00 00 00 00 <70> 63 69 30 30 30 30 3a 30 30 00 00 00 00 00 00 00 00 00 00 00
[    5.233426] RIP  [<ffff880105b34f20>] 0xffff880105b34f1f
[    5.259438]  RSP <ffff880101cd7b78>
[    5.275930] CR2: ffff880105b34f20
[    5.292461] ---[ end trace a040159f40b99a71 ]---
 ... [FAILED]
:: Loading module ohci-hcd[    5.320704] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 ... [  OK  ]
:: Loading module uhci-hcd[    5.355846] uhci_hcd: USB Universal Host Controller Interface driver
[   33.747328] Kernel panic - not syncing: Watchdog detected hard LOCKUP on cpu 1

 

 

Edited by Polanskiman
Added spoiler.

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23729 (fresh install)

- Loader version and model: v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASUS H81M-Plus with Realtek 8111G Gigabit LAN controller

- Additional comments: Fresh install was fine; after update there was no network

  • I made a new  installation with a PCIe NIC Intel 82572GI

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23729 (fresh install)

- Loader version and model: v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASUS H81M-Plus only with PCIe NIC Intel 82572GI

- Additional comments:

 

Share this post


Link to post
Share on other sites

- Outcome of the update: UNSUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: Intel NUC NUC5PPYH

- Additional comments: System Boot, but no Network, Realtek

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23729 (fresh install)

- Loader version and model: Jun's Loader v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - N54L DS3615XS with HP NC360T card

- Additional comments: Built-in NIC disabled. I couldn't get DS3617SX to work.

  • Like 1

Share this post


Link to post
Share on other sites
Posted (edited)

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 6  

- Loader version and model: Jun's LOADER v1.03b - Ds3615x

- Using custom extra.lzma: NO

- Installation type: ESXi 6.7 on Acer A100 Micro Server- Processeur Intel Pentium G630 - 4Go DDR

- Additional comments:

 

I created my own vmdk boot file and add a single HDD.
Vdmk boot on Sata 0 0: 1
HDD on Sata 0 0: 2 - persistent mode

After updating, it was impossible to see the machine on the network.
By changing the network adapter and Mac address everything works ^^
Network Adapter type: E1000e and MAC address in manual and you have to enter the boot file of the Ds3615x.

 

Spoiler

Capture d’écran 2019-03-03 à 18.52.54.png

 

Capture d’écran 2019-03-03 à 18.52.30.png

 

Capture d’écran 2019-03-03 à 18.53.06.png

 

Capture d’écran 2019-03-03 à 18.54.31.png

Edited by Polanskiman
Added spoiler.

Share this post


Link to post
Share on other sites
Posted (edited)

- Outcome of the update: SUCCESSFUL

- DSM version prior update: DSM 6.2.1-23824 Update 4 -> DSM 6.2.1-23824 Update 6

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J4105  - 8GB RAM

- Additional comments: NONE

Edited by deman-13

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.04b - DS918+

- Using custom extra.lzma: NO

- Installation type: BAREMETAL - ASRock J5005-ITX

Share this post


Link to post
Share on other sites

- Outcome of the installation/update: SUCCESSFUL

- DSM version prior update: DSM 6.2-23739

- Loader version and model: JUN'S LOADER v1.03b - DS3615xs

- Using custom extra.lzma: NO

- Installation type: VM - Cisco UCS C220 M3 - ESXi 6.7.0 Update2 Build 13644319

- Additional comments: Need to change NIC type from E1000 to E1000e and use SATA controller.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.