jsferra1 Posted September 29, 2018 Share #476 Posted September 29, 2018 Hello, I'm trying to do a clean install first time I have the image file I updated the grub.cfg file and changed the VID and PID and Serial and added what I have as the mac address (new system board never used) it's a Asrock B360M Pro4 I did a Diskpart and cleaned the USB stick then I wrote the boot loader to it and placed it in the new system and started it up, it booted to grub and I selected the first option to run JUN's loader 1.03b for 3617xs I received the screen about after the screen stops updating you can go to find.synology.com which I did and found nothing, then I downloaded the Synology Assistant and ran that and still found nothing, so I must have missed a step or maybe the mother broad wont work with the loader Any Ideas ? Thanks ..... Quote Link to comment Share on other sites More sharing options...
Hostilian Posted September 29, 2018 Share #477 Posted September 29, 2018 Try Legacy Boot (not UEFI) Try an add in NIC (Intel). Try using the DS3615 loader. Quote Link to comment Share on other sites More sharing options...
jsferra1 Posted September 29, 2018 Share #478 Posted September 29, 2018 1 hour ago, Hostilian said: Try Legacy Boot (not UEFI) Try an add in NIC (Intel). Try using the DS3615 loader. so do i need to update the grub.cfg with the vid and pid I see some how tos do that and some don't as for the UEFI I will see if I can change that or not but it did boot just could not find it using the website or the app to install the DSM ... I will see how bad I can mess it up .... Quote Link to comment Share on other sites More sharing options...
Hostilian Posted September 29, 2018 Share #479 Posted September 29, 2018 Just change your BIOS to boot Legacy, not UEFI.. Quote Link to comment Share on other sites More sharing options...
evolucja Posted September 29, 2018 Share #480 Posted September 29, 2018 (edited) Any chance to get it running on ASRock Q1900-ITX? Coming from 6.1. After Loader loads no IP is assigned and I can't access DSM / find it in Synology Assistant. In UEFI I enabled all "legacy compatibility" - CSM. Edited September 29, 2018 by evolucja Quote Link to comment Share on other sites More sharing options...
Hostilian Posted September 29, 2018 Share #481 Posted September 29, 2018 No, there should be a specific option in the BIOS to boot to LEGACY USB drive, rather than UEFI USB Disk.. Both options will be there.. Usually in the Boot options (Which drive to boot first). Boot to Legacy USB, Not UEFI.. Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted September 29, 2018 Share #482 Posted September 29, 2018 (edited) evolucja I took the initiative for you to Google "How to boot legacy mode ASRock Q1900-ITX" and found the info you need. For emphasis, i defer to Hostilians answer "Just change your Bios to Legacy not UEFI" this is correct. I've uploaded an image of your bios with the first boot option being boot from Legacy, and the second boot option booting from UEFI. You will want to select the USB "im assuming" device or ANY device for that matter, that does NOT have the "UEFI" label in it like you see in this image i've attached. In many cases nowadays, you will not find an option to completely change your bios to force legacy mode or at least the 200-300 motherboards i've came across in 2018 What you will find in newer boards is the option to choose Legacy OR UEFI within each boot option itself. Very important Also: Disable C1E - in your bios its labeled "C-states" i believe look at second image below for this disable Intel VTX if you can as well- 2nd image in your bios you also should look for usb settings and enable the usb to be seen as "hard drive" These will be optimal settings for your board to boot with XPE. Edited September 29, 2018 by Captainfingerbang 2 Quote Link to comment Share on other sites More sharing options...
evolucja Posted September 29, 2018 Share #483 Posted September 29, 2018 (edited) Yes, I did it before exactly like you're saying. I have only one device selected in boot options and it is the USB: pqi not the UEFI: pqi Edited September 29, 2018 by evolucja Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted September 29, 2018 Share #484 Posted September 29, 2018 do you see under "hard drive BBS priorities"? make sure NOTHING is selected in that. and look at my updated post. if none of that helps change anything, then you need to go back and remake the USB drive, following directions as if you have never made an XPE boot drive before Quote Link to comment Share on other sites More sharing options...
kanshudj Posted September 29, 2018 Share #485 Posted September 29, 2018 My hardware is j3455-itx, and dsm6.2 (ds918+) was successfully installed with 1.03a2 bootloder. During the process, I also encountered the problem that when i restarted the host after installation, the host is missed. I am preparing to test all functions today. Note: 1. legacy bios with USB bootloader and put in the first place, the hard disk uses ahci mode. 2. After the installation restarts, check if the bios boot is restored to uefi. This is my case but I don't know why. Then be patient and wait ,when the system startup, it may be very slow. when I didn't see any information on the screen and I saw a black screen, I found the ip ip. Quote Link to comment Share on other sites More sharing options...
evolucja Posted September 29, 2018 Share #486 Posted September 29, 2018 1 hour ago, Captainfingerbang said: do you see under "hard drive BBS priorities"? make sure NOTHING is selected in that. and look at my updated post. if none of that helps change anything, then you need to go back and remake the USB drive, following directions as if you have never made an XPE boot drive before I went from scratch and got it discovered once but wasn't working fully (GUI not accessiable etc.). I restarted and now I got the bootloop after the "Booting the kernel". Any more ideas? Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted September 30, 2018 Share #487 Posted September 30, 2018 if it were me, i would just install 6.1 on UEFI. SInce that IS what i currently am on Beggars cant be choosey! a couple things to do before you do that: make certain that C1E and vtx are disabled. 100%! then i would boot the computer to the Boot menu (f8 for asus if i remember correct), where it gives you a few options to force boot to the source of your choosing.i.e usb force boot, and also try "reinstall" option at Jun's boot screen Quote Link to comment Share on other sites More sharing options...
neopet001 Posted October 1, 2018 Share #488 Posted October 1, 2018 (edited) On 8/2/2018 at 11:29 PM, sliders said: hello ,Thank you very much jun Jun's Mod 1.03b - DS3617 Installation type: HP Z210 Workstation Intel Xeon E3-1280 we find no networks with SynologyAssistant 😞😟 2 Hello, Thank you Jun, I am using HP Z210 Workstation Intel Xeon E3-1245 Can't find networks with Synology Assistant too. 😅 More info: - The workstation only booted with the USB in UEFI mode and went through but couldn't find the NAS. - Legacy boot stopped right away with the blinking cursor. - It works on 6.1 (1.02b) Edited October 1, 2018 by neopet001 Quote Link to comment Share on other sites More sharing options...
smccloud Posted October 1, 2018 Share #489 Posted October 1, 2018 I'm going to switch my N40L back to Xpenology after getting fed up with Windows. Will this work with DSM 6.2.1? Quote Link to comment Share on other sites More sharing options...
Super169 Posted October 1, 2018 Share #490 Posted October 1, 2018 (edited) I tried to install a new VM, or upgrade the existing VM by replacing the 6.2 loader, both of them will stuck in the following screen. I have tried different options from this post, 1) set Boot Options to BIOS (actually there has no other choice in my VM setting) 2) modify the grub.cfg in bootloader, and change DiskIdxMap=0C to DiskIdxMap=0C00 3) Set the loader disk as IDE instead of SCSI All failed. I'm now running vSphere 6.5.0 on the server with 2 x E5-2660V2 on Intel W2600CR MB, will this be the problem of dual CPU? It works fine in v6.1.7, just cannot boot in v6.2. Any suggestion? Thanks in advance. Edited October 1, 2018 by Super169 Quote Link to comment Share on other sites More sharing options...
luchuma Posted October 1, 2018 Share #491 Posted October 1, 2018 @Super169 Quote Link to comment Share on other sites More sharing options...
Super169 Posted October 1, 2018 Share #492 Posted October 1, 2018 19 minutes ago, luchuma said: @Super169 Oh, I have missed your post before. It seems that I have used wrong disk type, it should be SATA not IDE. After comment the options in grub.cfg, and changing the disk setting to SATA as in your post, it seems OK now, and it allow me to migrate the existing disk. Thanks a lot. Quote Link to comment Share on other sites More sharing options...
Hostilian Posted October 1, 2018 Share #493 Posted October 1, 2018 Hate to ask, but I'm gonna. Any update on progress on a newer version of the loader - maybe to nail these DSM 6.2.1 issues? It's been a couple of months (happy birthday, 1.03b) since the last one.. Cheers, #H Quote Link to comment Share on other sites More sharing options...
Captainfingerbang Posted October 1, 2018 Share #494 Posted October 1, 2018 I'm looking for a guide just like "Tutorial - Install DSM 6.2 on ESXi 6.7" except i need the guide for Baremetal. Can anyone point me to this? Quote Link to comment Share on other sites More sharing options...
Dfds Posted October 1, 2018 Share #495 Posted October 1, 2018 5 hours ago, smccloud said: I'm going to switch my N40L back to Xpenology after getting fed up with Windows. Will this work with DSM 6.2.1? Yes, remember to disable C1E support in the bios. Quote Link to comment Share on other sites More sharing options...
kosovari Posted October 2, 2018 Share #496 Posted October 2, 2018 Have an hp Gen8 and trying to update from 6.1.6 to 6.2 but I get no hdd found what to do. Usb prepared with vid pid ya everything. Please help what to do. Quote Link to comment Share on other sites More sharing options...
neopet001 Posted October 2, 2018 Share #497 Posted October 2, 2018 10 hours ago, kosovari said: Have an hp Gen8 and trying to update from 6.1.6 to 6.2 but I get no hdd found what to do. Usb prepared with vid pid ya everything. Please help what to do. Have you checked your SATA controller and used the extra ramdisk? Quote Link to comment Share on other sites More sharing options...
kosovari Posted October 2, 2018 Share #498 Posted October 2, 2018 No I havent on both questions. Quote Link to comment Share on other sites More sharing options...
kosovari Posted October 2, 2018 Share #499 Posted October 2, 2018 How do I do that Quote Link to comment Share on other sites More sharing options...
sbv3000 Posted October 2, 2018 Share #500 Posted October 2, 2018 23 hours ago, Captainfingerbang said: I'm looking for a guide just like "Tutorial - Install DSM 6.2 on ESXi 6.7" except i need the guide for Baremetal. Can anyone point me to this? just follow the 5.2/6.1 bare metal tutorial 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.