Niels_J Posted February 1, 2022 Share #1951 Posted February 1, 2022 On 10/28/2021 at 4:01 PM, Holger1965 said: i‘d like to build on a Gen8 Hp Server My server is upgraded to XEON E3-1320v2 Hi Holger, Did you succeed? What did you upgrade from? Quote Link to comment Share on other sites More sharing options...
Dfds Posted February 1, 2022 Share #1952 Posted February 1, 2022 @Niels_Jthe gen8 will happily run DSM 6.2.3 with jun’s 1.03b loader or if you want to try DSM 7 you can build a loader using redpill tinycore, see the thread in the developer discussion section. Quote Link to comment Share on other sites More sharing options...
Niels_J Posted February 1, 2022 Share #1953 Posted February 1, 2022 29 minutes ago, Dfds said: @Niels_Jthe gen8 will happily run DSM 6.2.3 with jun’s 1.03b loader or if you want to try DSM 7 you can build a loader using redpill tinycore, see the thread in the developer discussion section. Thank you for the info! The 6.2.3 is the one in the first post in this thread, correct? And now for the absolute 100% noob question: Do I just place the img-file on the USB stick, or do I need to edit something in the file and compile it with ... etc ? If so, where might I find the programs for it? Quote Link to comment Share on other sites More sharing options...
gadreel Posted February 2, 2022 Share #1954 Posted February 2, 2022 4 hours ago, Niels_J said: Thank you for the info! The 6.2.3 is the one in the first post in this thread, correct? And now for the absolute 100% noob question: Do I just place the img-file on the USB stick, or do I need to edit something in the file and compile it with ... etc ? If so, where might I find the programs for it? For Jun's Loader yes, you need to open one of the partitions and edit the grub file with the appropriate S/N and Mac Address. Quote Link to comment Share on other sites More sharing options...
F.K. Posted February 20, 2022 Share #1955 Posted February 20, 2022 Hi folks, I had to reboot my machine, wondering that the GUI doesn't show up. Connected a monitor to the server and found a GRUB warning, saying: error incompatible license entering rescue mode.... Has anyone an idea what this means and how to get my server booting again? Thanks for any helpful advice My Server: HP ProLiant ML10 Gen9 Modellname DS3617xs Prozessor: INTEL Xeon D-1527 Prozessor-Taktrate 3.3 GHz RAM 8192 MB NIC: Intel-Ethernet I219-LM DSM-Version: DSM 6.1.7-15284 Update 3 Quote Link to comment Share on other sites More sharing options...
IG-88 Posted February 20, 2022 Share #1956 Posted February 20, 2022 1 hour ago, F.K. said: Hi folks, I had to reboot my machine, wondering that the GUI doesn't show up. Connected a monitor to the server and found a GRUB warning, saying: error incompatible license entering rescue mode.... Has anyone an idea what this means and how to get my server booting again? Thanks for any helpful advice My Server: HP ProLiant ML10 Gen9 Modellname DS3617xs Prozessor: INTEL Xeon D-1527 Prozessor-Taktrate 3.3 GHz RAM 8192 MB NIC: Intel-Ethernet I219-LM DSM-Version: DSM 6.1.7-15284 Update 3 you coud try to rebuild the loader on a new usb flash drive that the vanilla loader edit grub.cfg to mach the usb vid/pid of the new usb flash drive copy zImage, rd.gz and extra.lzma from old usb to the new one (all files on 2nd partiton) the try if the system boot again (if that work you can transfer SN and nic's mac from the olf grub.cfg to the new one) that way you dont change anything to what it is now, ols usb and system would still be the same if this attempt is a no good 1 Quote Link to comment Share on other sites More sharing options...
F.K. Posted February 20, 2022 Share #1957 Posted February 20, 2022 Hi thanks for your answer. I have simply recorded the USB bootstick with a new image. I did this about 4 years ago the last time - and I had a lot of jitters. But in fact it was much easier and faster under macOS than I feared. Now everything works again and my Synology version is finally on DSM 6.2.3-25426 Update 3 Quote Link to comment Share on other sites More sharing options...
alirz1 Posted April 14, 2022 Share #1958 Posted April 14, 2022 Hi all. I want to create a duplicate copy of my usb flash that has the jun”s loader on it.. in the past my usb drive died and I had to create a new one but I guess perhaps due to the vid/pid being different, It started my xpenology box as being new and I had do sort of a recover and restore data type of thing etc… if I create a copy of my current usb drive, should I use its vid/pid of the original drive in the cfg file on the new drive to prevent the loader from initializing the xpenology box if I ever have to swap out the usb loader flash drive? Quote Link to comment Share on other sites More sharing options...
signigelchan Posted June 4, 2022 Share #1959 Posted June 4, 2022 you're the best jun! Quote Link to comment Share on other sites More sharing options...
nickybg87 Posted June 11, 2022 Share #1960 Posted June 11, 2022 Is there a way to change the SN in the grub.cfg remotely (by ssh maybe) given the fact that pid & vid are set and the drive is not visible? Quote Link to comment Share on other sites More sharing options...
tomkoval Posted June 30, 2022 Share #1961 Posted June 30, 2022 (edited) To have correct MAC address for NIC you need to change it in /grub/grub.cfg file before booting NAS but if you forgot, there is still a chance to do it (and change serial number as well). To do so we need to change grub.cfg file on internal flash (see above). /dev/synoboot do not show in mount nor fdisk -l but still if you run fdisk -l /dev/synoboot you should see: Disk /dev/synoboot: 119.5 MiB, 125304832 bytes, 244736 sectors <- (size depends of usb drive used, here it is internal flash of Netgear ReadyNas Pro2) Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: AFB38D11-BCEA-4409-B348-F4FEEE602114 Device Start End Sectors Size Type /dev/synoboot1 2048 32767 30720 15M EFI System /dev/synoboot2 32768 94207 61440 30M Linux filesystem /dev/synoboot3 94208 102366 8159 4M BIOS boot Create folder somewhere (/) and mount first partition from above mount -o loop,offset=1048576 /dev/synoboot /temp where offset is sector size(512) multiplied by start sector of 1st partition(2048). Now you should have access to grub.cfg in grub folder. Change mac1 and mac2 to correct hardware addresses. After writing to file you can unmount /dev/synoboot and reboot to check if changes applied correctly. Edited June 30, 2022 by tomkoval corrections Quote Link to comment Share on other sites More sharing options...
gericb Posted July 3, 2022 Share #1962 Posted July 3, 2022 On 6/1/2021 at 3:00 PM, flyride said: 1.04b loader is UEFI bootable. The only loader that does not support UEFI is 1.03b (BIOS or CSM required). Curious... I tried today to create a Sandisk AND PNY USB drive with Rufus, using tinycore-redpill-uefi.v0.8.0.0.img, for a Dell 9020, set to UEFI booting by default. Manually doing F12 select UEFI Boot target, I get this error. If I F12 to Legacy Boot of the same USB, it boots up perfectly. Am I missing something? Thanks Quote Link to comment Share on other sites More sharing options...
gericb Posted July 3, 2022 Share #1963 Posted July 3, 2022 On 6/1/2021 at 3:00 PM, flyride said: 1.04b loader is UEFI bootable. The only loader that does not support UEFI is 1.03b (BIOS or CSM required). Curious... I tried today to create a Sandisk AND PNY USB drive with Rufus, using tinycore-redpill-uefi.v0.8.0.0.img, for a Dell 9020, set to UEFI booting by default. Manually doing F12 select UEFI Boot target, I get this error. If I F12 to Legacy Boot of the same USB, it boots up perfectly. Am I missing something? Thanks Quote Link to comment Share on other sites More sharing options...
flyride Posted July 4, 2022 Share #1964 Posted July 4, 2022 Unsure. I have TInycore running both UEFI and Legacy in test. I'm not disputing your experience or finding, but it it works, does it matter? For what it's worth, you are posting on the DSM 6 Jun loader thread, so what was written back in 2021 isn't applicable to Tinycore. Quote Link to comment Share on other sites More sharing options...
Spats Posted July 8, 2022 Share #1965 Posted July 8, 2022 Guys trying to setup DS918+ 6.2-2379 104b using real macs and serial, but getting this, does anyone know what is happening as i cannot setup my NAS and use quickconnect etc. was getting the same problem with v7 hence went to 6.2, i am stuck as to know what is happening. cheers guys Quote Link to comment Share on other sites More sharing options...
zzroman Posted July 10, 2022 Share #1966 Posted July 10, 2022 В 03.07.2022 в 21:45, gericb сказал: Curious... I tried today to create a Sandisk AND PNY USB drive with Rufus, using tinycore-redpill-uefi.v0.8.0.0.img, for a Dell 9020, set to UEFI booting by default. Manually doing F12 select UEFI Boot target, I get this error. If I F12 to Legacy Boot of the same USB, it boots up perfectly. Am I missing something? Thanks Try to use Win32DiskImager. Quote Link to comment Share on other sites More sharing options...
mikebanson Posted August 19, 2022 Share #1967 Posted August 19, 2022 On 8/14/2019 at 10:11 AM, Big_11 said: GOT IT !!!... I've succesfully installed DSM 6.2.2-24922 update 2 to my Supermicro Server !!!.. After a lot of fails with installing for 916+ or 918+ i tried the DS3615xs Version Took the 1.02 MBR Loader of Genesys and replaced the files with thes from 1.03b Loader… and it worked ! i'am happy thanks to all for your support and by now i am really more experienced !.. have a nice day.. please which files did you replace? Quote Link to comment Share on other sites More sharing options...
peltar Posted September 19, 2022 Share #1968 Posted September 19, 2022 I have tried getting this to run now on a Buffalo Terrastation 5400D for a few days now. After it does the install of DSM, and then reboots it will load into grub and say cannot find disk. I have tried doing this with the latest 6.2 DSM and loader as well as RedPILL and DSM 7. Quote Link to comment Share on other sites More sharing options...
mahone Posted November 16, 2022 Share #1969 Posted November 16, 2022 Thanks for your work! Quote Link to comment Share on other sites More sharing options...
azcat Posted November 17, 2022 Share #1970 Posted November 17, 2022 Thank you so much! Quote Link to comment Share on other sites More sharing options...
helldarkmonster Posted January 25 Share #1971 Posted January 25 Hi guys, is it possible to have a link for a 6.2 DSM loader MBR version DS3615xs. Thanks Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.