snowfox Posted September 20, 2019 Share #51 Posted September 20, 2019 On 12/17/2018 at 9:45 PM, Joly00 said: So, to give this Thread a Solution: Hardware Acceleration works for me with the j5005-ITX by Asrock when using the new 1.04b Jun Loader and install Emby (You have to enable VAAPI and not Intel Quick Sync). The /dev/dri folder is also available. Can you help me to install DSM918+_23824 with jun's 1.04b loader on Asrock J5005-ITX? I installed,but when it boot again, synology assistant can't find it. Quote Link to comment Share on other sites More sharing options...
sergelhr Posted October 17, 2019 Share #52 Posted October 17, 2019 search onto the forum for real3x mod, working for me with the latest dsm version update 3, now no more hardware acceleration ! Quote Link to comment Share on other sites More sharing options...
sergelhr Posted October 17, 2019 Share #53 Posted October 17, 2019 Hi @Polanskiman the correct software for the 5005-itx can be found here :xxxps://1drv.ms/u/s!Ap4vsEUrPToyh2746hR4GRDPPocn direct from asrock support; work under windows! 1 Quote Link to comment Share on other sites More sharing options...
adept Posted November 10, 2019 Share #54 Posted November 10, 2019 On 1/9/2019 at 2:19 PM, sergelhr said: @Eduardo Flash the Mac is not an issue, after contacting Asrock support, they gave me this tool (wMAC_v1.0.61.zip) you must run this tool from windows 10 cmd line, i did a win 10 enterprise temp install then a run that tool as usua,l wMAC c XXXXXXXXXX /s et voila Did you actually try it yourself? When I tried it did not quite work as expected, when trying to change the mac it will only let you change part of it, the rest is hardware manufacture specific. Quote Link to comment Share on other sites More sharing options...
adept Posted November 10, 2019 Share #55 Posted November 10, 2019 On 1/9/2019 at 2:19 PM, sergelhr said: @Eduardo Flash the Mac is not an issue, after contacting Asrock support, they gave me this tool (wMAC_v1.0.61.zip) you must run this tool from windows 10 cmd line, i did a win 10 enterprise temp install then a run that tool as usua,l wMAC c XXXXXXXXXX /s et voila Did you actually try it yourself? When I tried it did not quite work as expected, when trying to change the mac it will only let you change part of it, the rest is hardware manufacture specific. Quote Link to comment Share on other sites More sharing options...
premiero Posted January 23, 2020 Share #56 Posted January 23, 2020 On 11/10/2019 at 3:51 PM, adept said: Did you actually try it yourself? When I tried it did not quite work as expected, when trying to change the mac it will only let you change part of it, the rest is hardware manufacture specific. I did. I started Hiren's BootCD PE from my USB, than i ran wMAC tool provided by @sergelhr using bellow command: wMAC c 001122334455 /s Asrock J5005 ITX works like a charm with this tool. Just don't forget the /s at the end of command which is related to "skip MAC OUI check". Quote Link to comment Share on other sites More sharing options...
Eduardo Posted January 24, 2020 Share #57 Posted January 24, 2020 It worked here too. Quote Link to comment Share on other sites More sharing options...
premikkoci Posted January 24, 2020 Share #58 Posted January 24, 2020 Hi, Can you guys be more specific about Mac flash? I really have no idea what to do. Correct me if I am wrong but to have hw and sw transcoding active I need real Synology SN and MAC and to be able to WOL I need MBs MAC? Quote Link to comment Share on other sites More sharing options...
premiero Posted January 25, 2020 Share #59 Posted January 25, 2020 (edited) I think, I can confirm that both HW and SW transcoding are working on Asrock J5005 ITX. Original Jun 1.04b loader (no custom extra.lzma) DSM 6.2-23739 (DS918+) Real SN from my Synology DS918+ & MAC (onboard flashed) Need to check if Power Off / Reboot is working (as it did not at DSM 6.2.2-24922 Update 4) Edited January 25, 2020 by premiero Quote Link to comment Share on other sites More sharing options...
toyanucci Posted January 25, 2020 Share #60 Posted January 25, 2020 1 hour ago, premiero said: I think, I can confirm that both HW and SW transcoding are working on Asrock J5005 ITX. Original Jun 1.04b loader (no custom extra.lzma) DSM 6.2-23739 (DS918+) Real SN from my Synology DS918+ & MAC (onboard flashed) Need to check if Power Off / Reboot is working (as it did not at DSM 6.2.2-24922 Update 4) I have the asrock j4105. Do you think this will work in my case as well? Would I flash the Mac while still using 6.2.1 then update to 6.2.2? Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 25, 2020 Share #61 Posted January 25, 2020 1 hour ago, premiero said: Need to check if Power Off / Reboot is working (as it did not at DSM 6.2.2-24922 Update 4) from my experience thats because of a driver crashing on boot (kernel oops), by using a proper driver or removing the driver it should work atm its very likely to happen with jun's original or my old 918+ extra.lzma, unreleased 0.7 or newer will get rid of that for most cases so in case of shutdown problems check dmesg Quote Link to comment Share on other sites More sharing options...
premiero Posted January 25, 2020 Share #62 Posted January 25, 2020 2 minutes ago, IG-88 said: from my experience thats because of a driver crashing on boot (kernel oops), by using a proper driver or removing the driver it should work atm its very likely to happen with jun's original or my old 918+ extra.lzma, unreleased 0.7 or newer will get rid of that for most cases so in case of shutdown problems check dmesg Yeah, I saw Your posts in other topic. But can't test it ATM because of HDD parity check. dmesg - no erros, so there is a little chance it is working with this older DSM verision. Quote Link to comment Share on other sites More sharing options...
premiero Posted January 25, 2020 Share #63 Posted January 25, 2020 41 minutes ago, toyanucci said: I have the asrock j4105. Do you think this will work in my case as well? There is a good chance it will work. There is minor difference in CPU (same architecture, lower CPU and GPU clock, less -4 execution units). Quote Would I flash the Mac while still using 6.2.1 then update to 6.2.2? Flashing MAC in not an issue, You can do it whenever You want. Just don't forget to edit grub.conf. But I can't confirm that everyting will be working after upgrade. When I did first install of DSM 6.2.2-24922 Update 4, i had no dev/dri and shutodown/reboot was not working at all. Thats why i downgraded to 6.2-23739. Maybe instaling first 6.2 and than upgrading to 6.2.2-24922 Update 4 is the solution, but I haven't test it yet. Quote Link to comment Share on other sites More sharing options...
premikkoci Posted January 25, 2020 Share #64 Posted January 25, 2020 (edited) Can you describe how to flash a Mac address? I have a J4105itx.. Edited January 25, 2020 by premikkoci Quote Link to comment Share on other sites More sharing options...
premiero Posted January 25, 2020 Share #65 Posted January 25, 2020 (edited) Read this topic mate. You have all in it 😁. In case You didn't notice: First of all, You can't use DOS version of mactool, because this is UEFI only motherboard and do not support LEGACY mode. 1. Prepare pendrive. Write HirensBoot CD PE on it using ISO2USB HirenBootCD PE: https://www.hirensbootcd.org/files/HBCD_PE_x64.iso ISO2USB: https://www.hirensbootcd.org/files/ISO2USB.exe 2. Next unpack and copy MAC change tool: https://1drv.ms/u/s!Ap4vsEUrPToyh2746hR4GRDPPocn to this pendrive. 3. Boot from pendrive to Windows PE. Browse start menu and mount pendrive as C harddrive. 4. Type cmd. Go to the folder where You copied wMAC tool. 5. At commandline type: wMAC c YOUR_NEW_MAC_ADDRESS /s 6. Done. Edited January 25, 2020 by premiero Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 25, 2020 Share #66 Posted January 25, 2020 1 hour ago, premiero said: 2 hours ago, toyanucci said: I have the asrock j4105. Do you think this will work in my case as well? There is a good chance it will work. There is minor difference in CPU (same architecture, lower CPU and GPU clock, less -4 execution units). both are Gemini Lake (Goldmont Plus), J4105 is Intel UHD Graphics 600, the J5005 is Intel UHD Graphics 605 Intel GPU Gen 9.5: Kaby Lake, Coffee Lake, Gemini Lake afaik its using/needs different firmware (and driver support) then the original 918+ Apollo Lake cpu bxt* firmware for Apollo Lake (Goldmont line) glk* firmware for Geminilake (Goldmont Plus line) the i915 driver from synology does not have support for glk* firmware, only jun's new driver in 1.04b loader does support it Quote Link to comment Share on other sites More sharing options...
premiero Posted January 25, 2020 Share #67 Posted January 25, 2020 [Fri Jan 24 22:43:15 2020] [drm] GuC: No firmware known for this platform! [Fri Jan 24 22:43:15 2020] [drm] HuC: No firmware known for this platform! [Fri Jan 24 22:43:15 2020] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [Fri Jan 24 22:43:15 2020] [drm] Driver supports precise vblank timestamp query. [Fri Jan 24 22:43:15 2020] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [Fri Jan 24 22:43:15 2020] [drm] Finished loading DMC firmware i915/glk_dmc_ver1_04.bin (v1.4) [Fri Jan 24 22:43:15 2020] systemd-udevd[5868]: starting version 204 [Fri Jan 24 22:43:16 2020] [drm] failed to retrieve link info, disabling eDP [Fri Jan 24 22:43:16 2020] [drm] Initialized i915 1.6.0 20180514 for 0000:00:02.0 on minor 0 Thats how it is looking on J5005-ITX and juns 1.04b loader. Quote Link to comment Share on other sites More sharing options...
toyanucci Posted January 25, 2020 Share #68 Posted January 25, 2020 48 minutes ago, premiero said: Read this topic mate. You have all in it 😁. In case You didn't notice: First of all, You can't use DOS version of mactool, because this is UEFI only motherboard and do not support LEGACY mode. 1. Prepare pendrive. Write HirensBoot CD PE on it using ISO2USB HirenBootCD PE: https://www.hirensbootcd.org/files/HBCD_PE_x64.iso ISO2USB: https://www.hirensbootcd.org/files/ISO2USB.exe 2. Next unpack and copy MAC change tool: https://1drv.ms/u/s!Ap4vsEUrPToyh2746hR4GRDPPocn to this pendrive. 3. Boot from pendrive to Windows PE. Browse start menu and mount pendrive as C harddrive. 4. Type cmd. Go to the folder where You copied wMAC tool. 5. At commandline type: wMAC c YOUR_NEW_MAC_ADDRESS /s 6. Done. I'm gonna give it a whirl later when I get home. Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 25, 2020 Share #69 Posted January 25, 2020 15 minutes ago, premiero said: [Fri Jan 24 22:43:15 2020] [drm] GuC: No firmware known for this platform! [Fri Jan 24 22:43:15 2020] [drm] HuC: No firmware known for this platform! that might have been true when the driver jun used was recent actually there is "glk_guc_32.0.3.bin, glk_guc_33.0.0.bin, glk_huc_ver03_01_2893.bin, glk_huc_4.0.0.bin" in the linux kernel firmware archive, but when it's not used/loaded from the driver the its no use the rest is as expected after reading about intel gpu's and doing some summery (like the glk firmware usage for J5005) dmc -> Display Microcontroller, provides additional graphics low-power idle states guc -> Graphics micro (µ) Controlle, designed to perform graphics workload scheduling on the various graphics parallel engines huc -> HEVC/H.265 micro (µ) Controller, designed to offload some of the media functions from the CPU to GPU synology only packs dmc firmware with its dsm release, interestingly they also have the "glk_dmc_ver1_04.bin" in 918+ DSM but no support for it in the i915.ko they deliver with 6.2.2 Quote Link to comment Share on other sites More sharing options...
premikkoci Posted January 25, 2020 Share #70 Posted January 25, 2020 1 hour ago, premiero said: Thank you!!! just flashed Quote Link to comment Share on other sites More sharing options...
toyanucci Posted January 25, 2020 Share #71 Posted January 25, 2020 58 minutes ago, premiero said: [Fri Jan 24 22:43:15 2020] [drm] GuC: No firmware known for this platform! [Fri Jan 24 22:43:15 2020] [drm] HuC: No firmware known for this platform! [Fri Jan 24 22:43:15 2020] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [Fri Jan 24 22:43:15 2020] [drm] Driver supports precise vblank timestamp query. [Fri Jan 24 22:43:15 2020] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [Fri Jan 24 22:43:15 2020] [drm] Finished loading DMC firmware i915/glk_dmc_ver1_04.bin (v1.4) [Fri Jan 24 22:43:15 2020] systemd-udevd[5868]: starting version 204 [Fri Jan 24 22:43:16 2020] [drm] failed to retrieve link info, disabling eDP [Fri Jan 24 22:43:16 2020] [drm] Initialized i915 1.6.0 20180514 for 0000:00:02.0 on minor 0 Thats how it is looking on J5005-ITX and juns 1.04b loader. HW transcoding is working with just juns 1.04b loader and 6.2.2 after flashing the Mac? Quote Link to comment Share on other sites More sharing options...
IG-88 Posted January 25, 2020 Share #72 Posted January 25, 2020 3 minutes ago, toyanucci said: HW transcoding is working with just juns 1.04b loader and 6.2.2 after flashing the Mac? the part of the log has nothing to do with that, its just about the "base", the kernel driver and firmware creating /dev/dri devices in the system that have to be present when using the proprietary synology implementation (that you want to cheat) Quote Link to comment Share on other sites More sharing options...
toyanucci Posted January 25, 2020 Share #73 Posted January 25, 2020 12 minutes ago, IG-88 said: the part of the log has nothing to do with that, its just about the "base", the kernel driver and firmware creating /dev/dri devices in the system that have to be present when using the proprietary synology implementation (that you want to cheat) Yh, but does it work is alls I'm asking. That's the only reason j4105 users haven't updated to 6.2.2 as you know. Those that don't care about hw transcoding have updated though so I'm just curious if this will allow that to work. Quote Link to comment Share on other sites More sharing options...
premiero Posted January 26, 2020 Share #74 Posted January 26, 2020 (edited) 17 hours ago, toyanucci said: Yh, but does it work is alls I'm asking. That's the only reason j4105 users haven't updated to 6.2.2 as you know. Those that don't care about hw transcoding have updated though so I'm just curious if this will allow that to work. I just checked - no it's not working. Tried with 6.2.2-24922 Update 4, and 6.2.2-24922 Update 5. There was no dev/dri, and reboot / shutdown was not working. I have also tried @IG-88 0.6 driver extra test package, but still no succes - not able to power off/restart too and no HW transcoding. Edited January 26, 2020 by premiero Quote Link to comment Share on other sites More sharing options...
toyanucci Posted January 26, 2020 Share #75 Posted January 26, 2020 3 hours ago, premiero said: I just checked - no it's not working. Tried with 6.2.2-24922 Update 4, and 6.2.2-24922 Update 5. There was no dev/dri, and reboot / shutdown was not working. I have also tried @IG-88 0.6 driver extra test package, but still no succes - not able to power off/restart too and no HW transcoding. 😩 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.