gnoboot

XPEnology gnoBoot

Recommended Posts

Latest GNO with Intel NUC,

 

USB get's recognized as 2.0 still loads the xhci driver but uses the ehci driver ?

 

 

00:00.0 Class 0600: Device 8086:0154 (rev 09)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:02.0 Class 0300: Device 8086:0166 (rev 09)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=3]
Expansion ROM at  [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
	Address: 00000000  Data: 0000
Capabilities: [d0] Power Management version 2
	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-

00:16.0 Class 0780: Device 8086:1e3a (rev 04)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7c2c000 (64-bit, non-prefetchable) [size=1]
Capabilities: [50] Power Management version 3
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
	Address: 0000000000000000  Data: 0000

00:19.0 Class 0200: Device 8086:1503 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7c29000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=2]
Capabilities: [c8] Power Management version 2
	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Address: 00000000fee0100c  Data: 4171
Capabilities: [e0] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: e1000e

00:1a.0 Class 0c03: Device 8086:1e2d (rev 04) (prog-if 20)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c28000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1b.0 Class 0403: Device 8086:1e20 (rev 04)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4
Region 0: Memory at f7c20000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
	Address: 0000000000000000  Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
	DevCap:	MaxPayload 128 bytes, PhantFunc 0
		ExtTag- RBE-
	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
		MaxPayload 128 bytes, MaxReadReq 128 bytes
	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
Capabilities: [100 v1] Virtual Channel
	Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
	Arb:	Fixed- WRR32- WRR64- WRR128-
	Ctrl:	ArbSelect=Fixed
	Status:	InProgress-
	VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
		Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
		Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
		Status:	NegoPending- InProgress-
	VC1:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
		Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
		Ctrl:	Enable+ ID=1 ArbSelect=Fixed TC/VC=22
		Status:	NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
	Desc:	PortNumber=0f ComponentID=00 EltType=Config
	Link0:	Desc:	TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
		Addr:	00000000fed1c000

00:1d.0 Class 0c03: Device 8086:1e26 (rev 04) (prog-if 20)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7c27000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1f.0 Class 0601: Device 8086:1e56 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.2 Class 0106: Device 8086:1e03 (rev 04) (prog-if 01)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin B routed to IRQ 40
Region 0: I/O ports at f0d0 [size=1]
Region 1: I/O ports at f0c0 [size=1]
Region 2: I/O ports at f0b0 [size=1]
Region 3: I/O ports at f0a0 [size=1]
Region 4: I/O ports at f060 [size=2]
Region 5: Memory at f7c26000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Address: fee0500c  Data: 4151
Capabilities: [70] Power Management version 3
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
	Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ahci

00:1f.3 Class 0c05: Device 8086:1e22 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Interrupt: pin C routed to IRQ 5
Region 0: Memory at f7c25000 (64-bit, non-prefetchable) [size=11]
Region 4: I/O ports at f040 [size=2]

 

 

Also allot of errors:

 

[ 1435.579735] dsmnotify.cgi[17761]: segfault at 0 ip 000000000804ccb8 sp 00000000fffeee00 error 6
[ 1459.540217] dsmnotify.cgi[19541]: segfault at 0 ip 000000000804ccb8 sp 00000000ffea6f00 error 6
[ 1466.538000] dsmnotify.cgi[20054]: segfault at 0 ip 000000000804ccb8 sp 00000000ffcfe0a0 error 6
[ 1490.512849] dsmnotify.cgi[21703]: segfault at 0 ip 000000000804ccb8 sp 00000000ffd13c40 error 6
[ 1498.510178] dsmnotify.cgi[22251]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9d3aa0 error 6
[ 1523.484098] dsmnotify.cgi[24128]: segfault at 0 ip 000000000804ccb8 sp 00000000ff83dde0 error 6
[ 1529.468447] dsmnotify.cgi[24560]: segfault at 0 ip 000000000804ccb8 sp 00000000ffcfdea0 error 6
[ 1554.443824] dsmnotify.cgi[26298]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9a4e50 error 6
[ 1561.439088] dsmnotify.cgi[26767]: segfault at 0 ip 000000000804ccb8 sp 00000000ffc00a50 error 6
[ 1586.404155] dsmnotify.cgi[28616]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9efef0 error 6

Share this post


Link to post
Share on other sites
Kernel driver in use: r8168

 

There's already workaround posted in my blog. :lol: You have to rmmod GRUB option r8169_new. :wink: Have you tried that already?

 

kernel /zImage rmmod=r8169,r8169_new

 

 

From your blog:

 

To use r8168 (e.g R8111) driver, you need to blacklist r8169 driver according to this post.

 

rmmod=r8169_new

 

 

But I'm already using the r8168 driver so I don't understand why I need to blacklist the r8169 driver.

 

In any case I added the rmmod=r8169,r8169_new option and it is still disconnecting from the LAN.

Edited by Guest

Share this post


Link to post
Share on other sites
Latest GNO with Intel NUC,

 

USB get's recognized as 2.0 still loads the xhci driver but uses the ehci driver ?

 

 

00:00.0 Class 0600: Device 8086:0154 (rev 09)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:02.0 Class 0300: Device 8086:0166 (rev 09)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=3]
Expansion ROM at  [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
	Address: 00000000  Data: 0000
Capabilities: [d0] Power Management version 2
	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-

00:16.0 Class 0780: Device 8086:1e3a (rev 04)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7c2c000 (64-bit, non-prefetchable) [size=1]
Capabilities: [50] Power Management version 3
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
	Address: 0000000000000000  Data: 0000

00:19.0 Class 0200: Device 8086:1503 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7c29000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=2]
Capabilities: [c8] Power Management version 2
	Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Address: 00000000fee0100c  Data: 4171
Capabilities: [e0] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: e1000e

00:1a.0 Class 0c03: Device 8086:1e2d (rev 04) (prog-if 20)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c28000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1b.0 Class 0403: Device 8086:1e20 (rev 04)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4
Region 0: Memory at f7c20000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
	Address: 0000000000000000  Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
	DevCap:	MaxPayload 128 bytes, PhantFunc 0
		ExtTag- RBE-
	DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
		RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
		MaxPayload 128 bytes, MaxReadReq 128 bytes
	DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
Capabilities: [100 v1] Virtual Channel
	Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
	Arb:	Fixed- WRR32- WRR64- WRR128-
	Ctrl:	ArbSelect=Fixed
	Status:	InProgress-
	VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
		Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
		Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=01
		Status:	NegoPending- InProgress-
	VC1:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
		Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
		Ctrl:	Enable+ ID=1 ArbSelect=Fixed TC/VC=22
		Status:	NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
	Desc:	PortNumber=0f ComponentID=00 EltType=Config
	Link0:	Desc:	TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
		Addr:	00000000fed1c000

00:1d.0 Class 0c03: Device 8086:1e26 (rev 04) (prog-if 20)
Subsystem: Device 8086:2044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7c27000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1f.0 Class 0601: Device 8086:1e56 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.2 Class 0106: Device 8086:1e03 (rev 04) (prog-if 01)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
Interrupt: pin B routed to IRQ 40
Region 0: I/O ports at f0d0 [size=1]
Region 1: I/O ports at f0c0 [size=1]
Region 2: I/O ports at f0b0 [size=1]
Region 3: I/O ports at f0a0 [size=1]
Region 4: I/O ports at f060 [size=2]
Region 5: Memory at f7c26000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Address: fee0500c  Data: 4151
Capabilities: [70] Power Management version 3
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
	Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
	AFCap: TP+ FLR+
	AFCtrl: FLR-
	AFStatus: TP-
Kernel driver in use: ahci

00:1f.3 Class 0c05: Device 8086:1e22 (rev 04)
Subsystem: Device 8086:2044
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Interrupt: pin C routed to IRQ 5
Region 0: Memory at f7c25000 (64-bit, non-prefetchable) [size=11]
Region 4: I/O ports at f040 [size=2]

 

 

Also allot of errors:

 

[ 1435.579735] dsmnotify.cgi[17761]: segfault at 0 ip 000000000804ccb8 sp 00000000fffeee00 error 6
[ 1459.540217] dsmnotify.cgi[19541]: segfault at 0 ip 000000000804ccb8 sp 00000000ffea6f00 error 6
[ 1466.538000] dsmnotify.cgi[20054]: segfault at 0 ip 000000000804ccb8 sp 00000000ffcfe0a0 error 6
[ 1490.512849] dsmnotify.cgi[21703]: segfault at 0 ip 000000000804ccb8 sp 00000000ffd13c40 error 6
[ 1498.510178] dsmnotify.cgi[22251]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9d3aa0 error 6
[ 1523.484098] dsmnotify.cgi[24128]: segfault at 0 ip 000000000804ccb8 sp 00000000ff83dde0 error 6
[ 1529.468447] dsmnotify.cgi[24560]: segfault at 0 ip 000000000804ccb8 sp 00000000ffcfdea0 error 6
[ 1554.443824] dsmnotify.cgi[26298]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9a4e50 error 6
[ 1561.439088] dsmnotify.cgi[26767]: segfault at 0 ip 000000000804ccb8 sp 00000000ffc00a50 error 6
[ 1586.404155] dsmnotify.cgi[28616]: segfault at 0 ip 000000000804ccb8 sp 00000000ff9efef0 error 6

 

Then you either have to rmmod xhci or ehci in /etc/rc.local. Back read to know what's causing the segfaults.

Share this post


Link to post
Share on other sites

Hi

 

I am doing a native install on HP NL36. I burined the image gnoboot-alpha10.4-ext2.img to usb. When installing I get the errors, see image.

 

Can soneone tell me why this is happening and how to proceed to install without error. Even after rebooting the same error persists.

 

Thanks

IMG_19800113_160614.gif.716baa43697d45ad3d673b67e0327428.gif

Share this post


Link to post
Share on other sites
Hi

 

I am doing a native install on HP NL36. I burined the image gnoboot-alpha10.4-ext2.img to usb. When installing I get the errors, see image.

 

Can soneone tell me why this is happening and how to proceed to install without error. Even after rebooting the same error persists.

 

Thanks

 

gnoBoot has stated in his blog that this will be fixed with gnoboot-alpha10.5

 

"Fixed - Fixing recursive fault but reboot is needed"

Share this post


Link to post
Share on other sites

My set up is: one virtual disk to host the syno-boot-ext2 image. one 60GB virtual disk for initial installation; one LSI 9211-8i IT mode with one 160GB SSD, and two 4TB hard drives. Somehow the first disk starts with Disk 4. The 60GB is Disk 4; the 160GB SSD is Disk 5, and so on. Does anyone have similar issue? i saw someone posted here with first disk of Disk 3 (sdc) , and need to use the insmod during GRUB boot?

Share this post


Link to post
Share on other sites
My set up is: one virtual disk to host the syno-boot-ext2 image. one 60GB virtual disk for initial installation; one LSI 9211-8i IT mode with one 160GB SSD, and two 4TB hard drives. Somehow the first disk starts with Disk 4. The 60GB is Disk 4; the 160GB SSD is Disk 5, and so on. Does anyone have similar issue? i saw someone posted here with first disk of Disk 3 (sdc) , and need to use the insmod during GRUB boot?

 

For my motherboards, both Intel brand, I need to rmmod=ata_piix in grub. Or else DSM will start the array at slot 3 and onward (it seems to reserve the first 2 slots for that driver for some reason). You can try that in a test VM and see if your array starts at the correct slot. If not, then it's probably another driver.

 

edit: I guess it happens for me because I install gnoboot to a IDE vdmk rather than ACHI. https://ata.wiki.kernel.org/index.php/Ata_piix

 

On a side note, does anyone know if it's possible to run gnboot off a .flp (floppy image) rather than virtual hard drive? I tried to get it working, but got boot errors.

Share this post


Link to post
Share on other sites

Hello

 

I would like to upgrade my n54l.

It runs now under dsm 4.2 and I would like to install dsm 5.

I downloaded gnoboot 10.4, create a bootable usb key.

I plug the key on my n54l, switch it on, select gnoboot.me.

In synology assistant my Nas appear, but it is written "configuration lost".

When I right click on it the only choice is "install".

If I double click, a web page appear, adivisng me to backup my data ,and ask me where to find the firmware.

 

I didn't continue the process, because I don't know if this is normal.

From what I read, it would be written "migratable".

Can someone take a few minutes to explain me if it is normal, or if I did something wrong ?

 

Thanks a lot.

 

Ps : sorry for my english, since it is not my mother langage.

Share this post


Link to post
Share on other sites
Hello

 

I would like to upgrade my n54l.

It runs now under dsm 4.2 and I would like to install dsm 5.

I downloaded gnoboot 10.4, create a bootable usb key.

I plug the key on my n54l, switch it on, select gnoboot.me.

In synology assistant my Nas appear, but it is written "configuration lost".

When I right click on it the only choice is "install".

If I double click, a web page appear, adivisng me to backup my data ,and ask me where to find the firmware.

 

I didn't continue the process, because I don't know if this is normal.

From what I read, it would be written "migratable".

Can someone take a few minutes to explain me if it is normal, or if I did something wrong ?

 

Thanks a lot.no

 

Ps : sorry for my english, since it is not my mother langage.

 

Not sure, if you 4.2 would allow you to jump directly to 5.0. Take a backup first before you do anything as it should not be "configuration lost" if you have existing DSM installation.

Share this post


Link to post
Share on other sites

Ok. I try 1gain and with the right click i selected connect. I could have then put the new firmware. All is fine.

I just have a pb on windows. I can no more access my data by double clicking on the diskstation in the explorer. I m oboige to enter \\ip

Did i do something wrong ?

Share this post


Link to post
Share on other sites
Ok. I try 1gain and with the right click i selected connect. I could have then put the new firmware. All is fine.

I just have a pb on windows. I can no more access my data by double clicking on the diskstation in the explorer. I m oboige to enter \\ip

Did i do something wrong ?

I migrated my third xpenology from 4.3-3810 (trantors build r1.0) to 5.0-4458 just an hour ago. All my data and setting stayed unharmed. Except of remote permissions on all the shares. So I had to restore permissions manually (I mean - manually in DSM gui) for both nfs and smb access. May be it is also your case.

Share this post


Link to post
Share on other sites

Long time viewer, first time poster.

 

Just wanted to say thanks for this excellent piece of software. Successfully have DSM 5.0 running on an HP NL36 Microserver and an old HP ML110 G4. The old ML110 needed some crap disabled in the BIOS at first but nothing of importance at all, serial ports, IDE etc.

 

I do have a small issue that I'd like some help with or to find out if any one else is experiencing the same issue...

 

The NL36 is used as my main server and previously I had Trantor's DSM 4.2 installed. All ran fine but also had the DHCP package installed which worked wonderfully well.

 

Since upgrading to DSM 5.0 I see that DHCP is now built in and doesn't require an external package installed. My issues are:-

 

1. Clients with a DHCP leased address are not listed under the DHCP clients tab

2. The server is scheduled to power off then back on again between 3am - 7am, DHCP appears to fail until I disable and then re-enable it.

 

I have no idea if they are DSM 5.0 specific issues (a search on the Synology forums brings back no info) or whether it's something to do with gnoBoot?

 

I did perform a DSM 4.2 to 5.0 upgrade accepting the lost configuration, I don't see how this could cause this issue however.

 

Any pointers would be most appreciated :wink:

Share this post


Link to post
Share on other sites

Hi and thanks for your great work. I'm using gnoBoot 10.4 as my home server and another one as a backup server, both on ASUS C60M1-I. Both are working great, except one (major) issue with the backup server.

 

It seems that something in DSM 5.0 upgrade (on the real DS) broke Time Backup so that it is not able to do incremental network backups with any XPEnology as a target (though another real DS works fine). It always do "full" backups when using XPEnology as a target (while it does only "incremental" backup when using real DS as a target, which is correct behaviour). See my thread with full explanation of this issue here: http://xpenology.com/forum/viewtopic.php?f=2&t=2781

 

Could it be somehow related to the issue "Broken block-level iSCSI (LIO)", or is it another thing?

 

Thanks for any help.

Share this post


Link to post
Share on other sites

@FrankDeRyder,

It's probably DSM app related issue, my boot image is just a kernel and initramfs. It has nothing to do with the apps. :wink: For example, synozram script is broken because vendor is using PHP to calculate memory size which is missing from default installation.

 

@Kybla,

Might be, try another backup method (e.g. rsync) or wait for beta release that will include a working iSCSI block backend.

Share this post


Link to post
Share on other sites
My set up is: one virtual disk to host the syno-boot-ext2 image. one 60GB virtual disk for initial installation; one LSI 9211-8i IT mode with one 160GB SSD, and two 4TB hard drives. Somehow the first disk starts with Disk 4. The 60GB is Disk 4; the 160GB SSD is Disk 5, and so on. Does anyone have similar issue? i saw someone posted here with first disk of Disk 3 (sdc) , and need to use the insmod during GRUB boot?

 

For my motherboards, both Intel brand, I need to rmmod=ata_piix in grub. Or else DSM will start the array at slot 3 and onward (it seems to reserve the first 2 slots for that driver for some reason). You can try that in a test VM and see if your array starts at the correct slot. If not, then it's probably another driver.

 

edit: I guess it happens for me because I install gnoboot to a IDE vdmk rather than ACHI. https://ata.wiki.kernel.org/index.php/Ata_piix

 

On a side note, does anyone know if it's possible to run gnboot off a .flp (floppy image) rather than virtual hard drive? I tried to get it working, but got boot errors.

 

Interestingly, setting rmmod=ata_piix moves my first drive to disk 2.

Share this post


Link to post
Share on other sites

hello,

 

I 'am a new user of gnoboot 10.4 with DSM 5 4458 up 1 but i've problems with DSM :

 

after many hours ( aprox. 1 night), the web interface not respond, Windows file sharing and SSH works.

 

the only way to respond again, it is a hard reboot

 

I have this dsmeg loop log :

 

[90733.087315] WARNING: at drivers/ata/libata-scsi.c:4963 __ata_scsi_queuecmd+0x163/0x7e3()

[90733.087318] Hardware name: VC896AA-ABF s5118fr

[90733.087319] Modules linked in: ip6t_LOG nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables xt_limit xt_state xt_tcpudp xt_multiport ipt_LOG nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack iptable_filter ip_tables x_tables cifs udf isofs loop usbhid hid usblp usb_storage uhci_hcd etxhci_hcd xhci_hcd ohci_hcd ehci_hcd bromolow_synobios(P) btrfs zlib_deflate hfsplus md4 hmac i2c_algo_bit fuse vfat fat chainiv cpufreq_conservative cpufreq_powersave cpufreq_performance cpufreq_ondemand mperf processor cpufreq_stats freq_table dm_snapshot crc_itu_t quota_v2 quota_tree usbcore psnap p8022 llc usb_common synoacl_ext4(P) synoacl_vfs(P) hptiop 3w_sas 3w_9xxx 3w_xxxx mv61xx(P) mvsas hpsa arcmsr aic7xxx aic79xx aic94xx aacraid megaraid_sas megaraid_mbox megaraid_mm mpt2sas mptsas mptspi mptscsih mptbase scsi_transport_spi scsi_wait_scan sg ata_piix sata_uli sata_svw sata_qstor sata_inic162x sata_sis pata_sis stex sata_sx4 sata_promise sata_nv sata_via sata_sil pata_serverworks pata_atiixp pata_amd pata_oldpiix pata_sch pata_artop pata_atp867x pata_pdc202xx_old pata_pdc2027x pata_it821x pata_hpt3x2n pata_hpt37x pata_hpt366 pata_hpt3x3 pdc_adma pata_via pata_sil680 pata_rdc pata_ninja32 pata_netcell pata_marvell pata_jmicron pata_cmd64x pata_ali pata_acpi ata_generic iscsi_tcp libiscsi_tcp libiscsi enic qlge qlcnic qla3xxx netxen_nic mlx4_en mlx4_core cxgb4vf cxgb4 cxgb3 cxgb cnic ipv6 bnx2x bna be2net sis900 sis190 jme atl1e(O) atl1c atl2(O) atl1(O) alx(O) sky2 skge via_velocity crc_ccitt via_rhine r8169(O) r8168(O) 8139too 8139cp tg3(O) libphy b44(O) bnx2 mmc_core ssb uio forcedeth ixgbe ixgb igb_new(O) ioatdma e1000e_new(O) e1000 e100 dca pcnet32 amd8111e tulip mdio mii container fan thermal_sys compat(O) cryptd ecryptfs sha512_generic sha256_generic sha1_generic ecb aes_x86_64 authenc des_generic libcrc32c crc32c eseqiv krng ansi_cprng cts rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi [last unloaded: bromolow_synobios]

[90733.087420] Pid: 5125, comm: scsi_eh_2 Tainted: P WC O 3.2.40 #6

[90733.087421] Call Trace:

[90733.087424] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087427] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087430] [] ? warn_slowpath_common+0x78/0x8d

[90733.087433] [] ? ata_scsi_write_same_xlat+0x162/0x162

[90733.087436] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087439] [] ? ata_scsi_queuecmd+0x3f/0x70

[90733.087442] [] ? scsi_dispatch_cmd+0x295/0x2fe

[90733.087446] [] ? scsi_request_fn+0x4e7/0x516

[90733.087449] [] ? blk_run_queue+0x21/0x32

[90733.087452] [] ? scsi_run_queue+0x1f9/0x208

[90733.087455] [] ? scsi_block_when_processing_errors+0xce/0xce

[90733.087459] [] ? scsi_run_host_queues+0x16/0x2d

[90733.087462] [] ? scsi_error_handler+0x4df/0x5b1

[90733.087465] [] ? do_notify_parent+0x1a5/0x1b6

[90733.087468] [] ? __wake_up_common+0x46/0x75

[90733.087471] [] ? scsi_block_when_processing_errors+0xce/0xce

[90733.087474] [] ? kthread+0x6a/0x72

[90733.087478] [] ? kernel_thread_helper+0x4/0x10

[90733.087481] [] ? kthread_bind+0x5c/0x5c

[90733.087484] [] ? gs_change+0x13/0x13

[90733.087486] ---[ end trace 6b6535586e4aa643 ]---

 

Can you help me ? thks a lot for your awesome work !

Share this post


Link to post
Share on other sites

hello,

 

I 'am a new user of gnoboot 10.4 with DSM 5 4458 up 1 but i've problems with DSM :

 

after many hours ( aprox. 1 night), the web interface not respond, Windows file sharing and SSH works.

 

the only way to respond again, it is a hard reboot

 

I have this dsmeg loop log :

 

[90733.087315] WARNING: at drivers/ata/libata-scsi.c:4963 __ata_scsi_queuecmd+0x163/0x7e3()

[90733.087318] Hardware name: VC896AA-ABF s5118fr

[90733.087319] Modules linked in: ip6t_LOG nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables xt_limit xt_state xt_tcpudp xt_multiport ipt_LOG nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack iptable_filter ip_tables x_tables cifs udf isofs loop usbhid hid usblp usb_storage uhci_hcd etxhci_hcd xhci_hcd ohci_hcd ehci_hcd bromolow_synobios(P) btrfs zlib_deflate hfsplus md4 hmac i2c_algo_bit fuse vfat fat chainiv cpufreq_conservative cpufreq_powersave cpufreq_performance cpufreq_ondemand mperf processor cpufreq_stats freq_table dm_snapshot crc_itu_t quota_v2 quota_tree usbcore psnap p8022 llc usb_common synoacl_ext4(P) synoacl_vfs(P) hptiop 3w_sas 3w_9xxx 3w_xxxx mv61xx(P) mvsas hpsa arcmsr aic7xxx aic79xx aic94xx aacraid megaraid_sas megaraid_mbox megaraid_mm mpt2sas mptsas mptspi mptscsih mptbase scsi_transport_spi scsi_wait_scan sg ata_piix sata_uli sata_svw sata_qstor sata_inic162x sata_sis pata_sis stex sata_sx4 sata_promise sata_nv sata_via sata_sil pata_serverworks pata_atiixp pata_amd pata_oldpiix pata_sch pata_artop pata_atp867x pata_pdc202xx_old pata_pdc2027x pata_it821x pata_hpt3x2n pata_hpt37x pata_hpt366 pata_hpt3x3 pdc_adma pata_via pata_sil680 pata_rdc pata_ninja32 pata_netcell pata_marvell pata_jmicron pata_cmd64x pata_ali pata_acpi ata_generic iscsi_tcp libiscsi_tcp libiscsi enic qlge qlcnic qla3xxx netxen_nic mlx4_en mlx4_core cxgb4vf cxgb4 cxgb3 cxgb cnic ipv6 bnx2x bna be2net sis900 sis190 jme atl1e(O) atl1c atl2(O) atl1(O) alx(O) sky2 skge via_velocity crc_ccitt via_rhine r8169(O) r8168(O) 8139too 8139cp tg3(O) libphy b44(O) bnx2 mmc_core ssb uio forcedeth ixgbe ixgb igb_new(O) ioatdma e1000e_new(O) e1000 e100 dca pcnet32 amd8111e tulip mdio mii container fan thermal_sys compat(O) cryptd ecryptfs sha512_generic sha256_generic sha1_generic ecb aes_x86_64 authenc des_generic libcrc32c crc32c eseqiv krng ansi_cprng cts rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi [last unloaded: bromolow_synobios]

[90733.087420] Pid: 5125, comm: scsi_eh_2 Tainted: P WC O 3.2.40 #6

[90733.087421] Call Trace:

[90733.087424] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087427] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087430] [] ? warn_slowpath_common+0x78/0x8d

[90733.087433] [] ? ata_scsi_write_same_xlat+0x162/0x162

[90733.087436] [] ? __ata_scsi_queuecmd+0x163/0x7e3

[90733.087439] [] ? ata_scsi_queuecmd+0x3f/0x70

[90733.087442] [] ? scsi_dispatch_cmd+0x295/0x2fe

[90733.087446] [] ? scsi_request_fn+0x4e7/0x516

[90733.087449] [] ? blk_run_queue+0x21/0x32

[90733.087452] [] ? scsi_run_queue+0x1f9/0x208

[90733.087455] [] ? scsi_block_when_processing_errors+0xce/0xce

[90733.087459] [] ? scsi_run_host_queues+0x16/0x2d

[90733.087462] [] ? scsi_error_handler+0x4df/0x5b1

[90733.087465] [] ? do_notify_parent+0x1a5/0x1b6

[90733.087468] [] ? __wake_up_common+0x46/0x75

[90733.087471] [] ? scsi_block_when_processing_errors+0xce/0xce

[90733.087474] [] ? kthread+0x6a/0x72

[90733.087478] [] ? kernel_thread_helper+0x4/0x10

[90733.087481] [] ? kthread_bind+0x5c/0x5c

[90733.087484] [] ? gs_change+0x13/0x13

[90733.087486] ---[ end trace 6b6535586e4aa643 ]---

 

Can you help me ? thks a lot for your awesome work !

Share this post


Link to post
Share on other sites

hello,

 

I 'am a new user of gnoboot 10.4 with DSM 5 4458 up 1 but i've problems with DSM :

 

after many hours ( aprox. 1 night), the web interface not respond, Windows file sharing and SSH works.

 

the only way to respond again, it is a hard reboot

 

I have this dsmeg loop log :

 

[90733.087315] WARNING: at drivers/ata/libata-scsi.c:4963 __ata_scsi_queuecmd+0x163/0x7e3()
[90733.087318] Hardware name: VC896AA-ABF s5118fr
[90733.087319] Modules linked in: ip6t_LOG nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables xt_limit xt_state xt_tcpudp xt_multiport ipt_LOG nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack iptable_filter ip_tables x_tables cifs udf isofs loop usbhid hid usblp usb_storage uhci_hcd etxhci_hcd xhci_hcd ohci_hcd ehci_hcd bromolow_synobios(P) btrfs zlib_deflate hfsplus md4 hmac i2c_algo_bit fuse vfat fat chainiv cpufreq_conservative cpufreq_powersave cpufreq_performance cpufreq_ondemand mperf processor cpufreq_stats freq_table dm_snapshot crc_itu_t quota_v2 quota_tree usbcore psnap p8022 llc usb_common synoacl_ext4(P) synoacl_vfs(P) hptiop 3w_sas 3w_9xxx 3w_xxxx mv61xx(P) mvsas hpsa arcmsr aic7xxx aic79xx aic94xx aacraid megaraid_sas megaraid_mbox megaraid_mm mpt2sas mptsas mptspi mptscsih mptbase scsi_transport_spi scsi_wait_scan sg ata_piix sata_uli sata_svw sata_qstor sata_inic162x sata_sis pata_sis stex sata_sx4 sata_promise sata_nv sata_via sata_sil pata_serverworks pata_atiixp pata_amd pata_oldpiix pata_sch pata_artop pata_atp867x pata_pdc202xx_old pata_pdc2027x pata_it821x pata_hpt3x2n pata_hpt37x pata_hpt366 pata_hpt3x3 pdc_adma pata_via pata_sil680 pata_rdc pata_ninja32 pata_netcell pata_marvell pata_jmicron pata_cmd64x pata_ali pata_acpi ata_generic iscsi_tcp libiscsi_tcp libiscsi enic qlge qlcnic qla3xxx netxen_nic mlx4_en mlx4_core cxgb4vf cxgb4 cxgb3 cxgb cnic ipv6 bnx2x bna be2net sis900 sis190 jme atl1e(O) atl1c atl2(O) atl1(O) alx(O) sky2 skge via_velocity crc_ccitt via_rhine r8169(O) r8168(O) 8139too 8139cp tg3(O) libphy b44(O) bnx2 mmc_core ssb uio forcedeth ixgbe ixgb igb_new(O) ioatdma e1000e_new(O) e1000 e100 dca pcnet32 amd8111e tulip mdio mii container fan thermal_sys compat(O) cryptd ecryptfs sha512_generic sha256_generic sha1_generic ecb aes_x86_64 authenc des_generic libcrc32c crc32c eseqiv krng ansi_cprng cts rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi [last unloaded: bromolow_synobios]
[90733.087420] Pid: 5125, comm: scsi_eh_2 Tainted: P        WC O 3.2.40 #6
[90733.087421] Call Trace:
[90733.087424]  [] ? __ata_scsi_queuecmd+0x163/0x7e3
[90733.087427]  [] ? __ata_scsi_queuecmd+0x163/0x7e3
[90733.087430]  [] ? warn_slowpath_common+0x78/0x8d
[90733.087433]  [] ? ata_scsi_write_same_xlat+0x162/0x162
[90733.087436]  [] ? __ata_scsi_queuecmd+0x163/0x7e3
[90733.087439]  [] ? ata_scsi_queuecmd+0x3f/0x70
[90733.087442]  [] ? scsi_dispatch_cmd+0x295/0x2fe
[90733.087446]  [] ? scsi_request_fn+0x4e7/0x516
[90733.087449]  [] ? blk_run_queue+0x21/0x32
[90733.087452]  [] ? scsi_run_queue+0x1f9/0x208
[90733.087455]  [] ? scsi_block_when_processing_errors+0xce/0xce
[90733.087459]  [] ? scsi_run_host_queues+0x16/0x2d
[90733.087462]  [] ? scsi_error_handler+0x4df/0x5b1
[90733.087465]  [] ? do_notify_parent+0x1a5/0x1b6
[90733.087468]  [] ? __wake_up_common+0x46/0x75
[90733.087471]  [] ? scsi_block_when_processing_errors+0xce/0xce
[90733.087474]  [] ? kthread+0x6a/0x72
[90733.087478]  [] ? kernel_thread_helper+0x4/0x10
[90733.087481]  [] ? kthread_bind+0x5c/0x5c
[90733.087484]  [] ? gs_change+0x13/0x13
[90733.087486] ---[ end trace 6b6535586e4aa643 ]---


 

 

Can you help me ? thks a lot for your awesome work !

Share this post


Link to post
Share on other sites

Thanks gnoboot for your 10.5 update.

 

I have updated to 10.5, but unlucky, I have a SATA HD connected on the original DVDROM sata connector, and that disk couldn't be found after the upgrade, I tried both vanilla and modified version, all failed, then I switched back to 10.4 and the disk was back.

 

I am using N40L.

Share this post


Link to post
Share on other sites
Thanks gnoboot for your 10.5 update.

 

I have updated to 10.5, but unlucky, I have a SATA HD connected on the original DVDROM sata connector, and that disk couldn't be found after the upgrade, I tried both vanilla and modified version, all failed, then I switched back to 10.4 and the disk was back.

 

I am using N40L.

 

Thank you for the advise!! That disk is very important for me and I can't loose it! Will stay in 10.4 until more information.

Share this post


Link to post
Share on other sites
Thanks gnoboot for your 10.5 update.

 

I have updated to 10.5, but unlucky, I have a SATA HD connected on the original DVDROM sata connector, and that disk couldn't be found after the upgrade, I tried both vanilla and modified version, all failed, then I switched back to 10.4 and the disk was back.

 

I am using N40L.

 

Try to insmod pata_amd or pata_acpi.

Share this post


Link to post
Share on other sites

Thank you gnoboot for your work on this, im having a small problem.

 

Im trying to run gnoboot on ESXi 5.5 with the sata-controller on the hosts motherboard passed through to the synology box.

 

The motherboard is a Asrock z77 extreme4 with an i7 3770 cpu mounted.

 

gnoboot works fine without the device passed through, but when i pass the AHCI controller to the synology VM it kernel panics during boot like this:

HTXMGQP.png, is Panther Point AHCI controller not supported? (Should i get a seperate raid card and pass that through instead? if so, will a LSI MegaRAID SAS 9240-4i SGL or a cheaper Sunway raidcard with a Silicon Image SiI3114 chip work?)

 

Also follow up question, can i change the model from DS3612xs to sometihng like DS412+? (im planning on using the synology VM with 4 physical disks inside one of these, the web gui would just look nicer if it was for a model with only 4 drives)

Share this post


Link to post
Share on other sites

*

For me i have always problem with Realtek network card 10DE:8136 rev=02 ( motherboard HP IPMEL-AE PEGATRON )

no IP ...?

 

 

addon cards

8086:1229 rev=02 OK

10DE:8169 rev=02 OK

 

I have a log with RR62x failed ...with no card in the computer

 

if i plug a RR622 card run , no problem in sata mode with only one HDD no RAID << fine ****

 

*** to change something or it really takes me a very detailed explanation **

** I know almost nothing linux !! ***

 

Pierre

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now