Search the Community
Showing results for tags 'g8'.
Found 3 results
Buenos días, Hace tiempo que tengo un Hp G8 con RAM ampliada a 12 Gb pero con el procesador más bajo que venía, me gustaría actualizar la CPU pues tengo montado un proxmox para máquinas virtuales y con ese procesador tengo cuello de botella con los windows server 2012. Me gustaría meter un Xeon lo más potente posible y que al que le valga el disipador que viene en el G8 sin riesgo de freirlo. También me gustaría que no subiese demasiado el consumo eléctrico. He visto varios posts, que hablan del Xeon e-3 1265L v2, me gustaría tener una opinión de alguien que haya cambiado a eso o a otro micro y que me de su opinión. También me gustaría saber qué hay que hacer después de cambiar el micro, si hay que cambiar alguna opción de la BIOS o no es necesario y dónde puedo comprarlo, parece que está complicado encontrarlos Muchas gracias
Had a HP Microserver G8 chassis with defunct MB collecting dust. Replacing the proprietary MB felt pointless, so I decided to cram in the leftovers from upgrading the gaming rig and install Xpenology. The list of odd bits available: i5-4670T Noctua NH-L9i ASUS Z87i Pro, mITX SilentWings 120mm PWM Fan I wanted better CPU than the anaemic G1610T and yet limit power usage. I also wanted something more quiet than the original HP system fan. The backplate of the MB-tray in the G8 is too small to fit an entire mITX MB I/O shield. I decided to stay within the edges of the Hp backplate, otherwise one needs to cut(yes, I used the dremel) through the edge of the MB tray and also into the top cover. Cutting through the edge would affect structural stability and usability. Here I sacrificed access to the leftmost ports of the replacement MB, but for use in a NAS they were not essential. To reposition the posts to screw down the MB on the tray, first use a big pair of pliers and give a good twist to remove. I then put in a PCI card to help find the correct position for the MB onto the tray using the expansion card opening as a guide. Then cut an opening for the I/O shield. "Measure twice, cut once" does still apply here, but be prepared to do some extra trimming to make things fit reasonably. Marked the positions for the mounting posts through the MB holes. Tapped and drilled new holes which I kept slightly undersized. Pushed the posts into the holes and pounded them in place. Use a piece of wood(with a hole for the post) as a counter. Reused the rubber studs/distances that the support the original MB onto the tray and repositioned holistically. The Noctua CPU cooler did slide in nicely underneath the drive cage. Then some soldering to extend the Molex power cable for the CPU-power and power connectors for additional disks. Also added a ATX-power extension cable to reach to the new position of the MB power connector. Another fun discovery is the proprietary nature of the HP top front USB ports/cables and the system panel connector(PWR/reset/LEDs). I removed the original front USB ports and glued a 2-port USB 3.0 Female Flat Cable with a 20 Pin Header in place. I also pried open the plastic housing of the power button and added(yes, more glue) a generic pushpin power switch and LEDs inside. It all looks stock from the outside and works just fine. Then my brother got involved and decided to sponsor my project with some storage: LSI 9271-8i 4 x ST6000NM0014 2 x Samsung MZ7GE480HMHP Yes, these are some luxury items and one could naturally have used any odd SATA HDD here. Also note that the original HP SATA harness mounted to the drive cage has a SFF-8087 header. Using the LSI card this snapped right in. Otherwise some rewiring would have had to be performed. Using the existing cabling/connectors to the the drive cages and an LSI-card also provided hot swappable disks and no 3Gbps limitation as imposed by HP onto some slots by the original onboard SATA/RAID controller. The LSI controller is configured to present the disks as JBOD, leaving DSM to apply soft RAID(5) to the volume(s). To work with the LSI command level interface when rebuilding a hardware RAID volume, one needs to possess superpowers that I don't. Configured the SSDs as R/W cache and the system feels very snappy. I have 16MB of DRAM installed which is probably overkill, as I don't have any plans to launch VMs. Installed Xpenology as DS3615xs, and for VideoStation the CPU architecture seems to play nice with transcoding. The access to video and fast forward while playing is almost instant. I'm not sharing any pics of the innards, as my wiring skills are not up to public scrutiny
Hello community, I was googling for an hour now and was not able to find any guide how to upgrade from 6.0.2 to 6.1.X on my HP MS G8. Using Jun's loader for the 6.0.2 booting from USB. Please send me a link or advice, how I can upgrade without loosing the Config and Data. Thanks