Search the Community
Showing results for tags 'ds918'.
Found 2 results
Hi, I removed the faulty i915 drivers from extra, you can download and test it here. hw transcoding is working but performance is low on both videostation and plex but I don't think is related to the loader. on ASRock j4205-ITX you have to unplug any monitor before using hw transcoding otherwise the system will reboot, this one might be due to /dev/dri permissions or the DP to hdmi coverter on this board. reboot/shutdown is working properly again. I recommend doing a clean install, formatting the hard drive before testing. You can test disabling video outputs in the grub, for me it didn't install properly. video=eDP:d video=DP-1:d video=HDMI-A-1:d video=HDMI-A-2:d root@DS918:~# ls /dev/dri card0 controlD64 renderD128 root@DS918:~# cat /sys/kernel/debug/dri/0/i915_frequency_info PM IER=0x00000070 IMR=0xffffff8f ISR=0x00000000 IIR=0x00000000, MASK=0x00003fae pm_intr_keep: 0x80000000 GT_PERF_STATUS: 0x006030cb Render p-state ratio: 48 Render p-state VID: 203 Render p-state limit: 0 RPSTAT1: 0x12000030 RPMODECTL: 0x00000d92 RPINCLIMIT: 0x000027d8 RPDECLIMIT: 0x00005a00 RPNSWREQ: 800MHz CAGF: 600MHz RP CUR UP EI: 3192 (2660us) RP CUR UP: 477 (397us) RP PREV UP: 0 (0us) Up threshold: 85% RP CUR DOWN EI: 5109 (4257us) RP CUR DOWN: 482 (401us) RP PREV DOWN: 0 (0us) Down threshold: 60% Lowest (RPN) frequency: 100MHz Nominal (RP1) frequency: 250MHz Max non-overclocked (RP0) frequency: 800MHz Max overclocked frequency: 800MHz Current freq: 800 MHz Actual freq: 600 MHz Idle freq: 100 MHz Min freq: 100 MHz Boost freq: 800 MHz Max freq: 800 MHz efficient (RPe) frequency: 250 MHz Current CD clock frequency: 624000 kHz Max CD clock frequency: 624000 kHz Max pixel clock frequency: 624000 kHz [ 127.551937] ACPI: Power Button [PWRB] [ 127.601681] Linux agpgart interface v0.103 [ 127.674041] [drm] Initialized drm 1.1.0 20060810 [ 127.809306] [drm] Memory usable by graphics device = 4096M [ 127.882071] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 127.882075] [drm] Driver supports precise vblank timestamp query. [ 127.884752] [drm] Finished loading i915/bxt_dmc_ver1_07.bin (v1.7) [ 127.885302] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 128.859977] [drm] failed to retrieve link info, disabling eDP [ 128.861274] [drm] GuC firmware load skipped [ 128.865805] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 128.866518] acpi device:10: registered as cooling_device4 [ 128.866603] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input1 [ 128.866659] [drm] Initialized i915 1.6.0 20160919 for 0000:00:02.0 on minor 0 [ 128.882007] i915 0000:00:02.0: No connectors reported connected with modes [ 128.882013] [drm] Cannot find any crtc or sizes - going 1024x768 [ 128.882929] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device [ 128.938416] Btrfs loaded, crc32c=crc32c-intel
So I have been trying to migrate from a DS3615XS with Jun's loader 1.02b to DS918+ and Jun's loader 1.04b. I have a baremetal Asus Z170M Plus which has an Intel I219V NIC. Posts by other users say that this is a compatible NIC. My NAS is being picked up by the Synology app and web service, it is listed as a 918 and migratable, Jun's loader appears to load fine. I have tried using a manual install of PAT 6.2 and 6.21. I am getting the error message, 'Failed to install file. The file is probably corrupted (13)'. I know this is often an error in your PID or VID so I have attached screenshots of my PID/VID and Grub file. I have also tried downloading the latest PAT direct to the device, and receive an error message, 'Failed to download the DSM installation file. Please check the network connection and try again (46)'. I think there might be a clue here. Right now I have probably blown away my DSM installation, I was getting desperate so I tried a fresh DSM install migration (formatting DSM, but keeping your data).