komarto

Members
  • Content count

    28
  • Joined

  • Last visited

Community Reputation

0 Neutral

About komarto

  • Rank
    Junior Member
  1. komarto

    DSM 6.1.x Loader

    There are two versions of the loader 3615xs and 3617xs, what should we use when migrating from 1.01 which is 3615xs based?
  2. komarto

    Drivers requests for DSM 5.2

    Yes, please add the support for the Intel i211 and Marvell 88SE9215. Thanks !! 88SE9215 is already supported I am using it on DSM 6. see my signature below.
  3. komarto

    DSM 6.1.x Loader

    Update 9 is the devil After updating I did not have any network... Had to go to serial console and downgrade to version 5.2. after upgrading back to version 6 update8 with jun loader I noticed that my Realtek card is not working anymore just my intel card. I noticed that module r8168 is not loaded when DSM is done loading. when I insmod the module I see eth2 with ifconfig -a but it has the same MAC address as eth0... I tried setting MAC address through the GRUB config, but with no avail... The module will not self load on boot only manually and when i look at eth2 using ifconfig -a it has the same MAC as eth0. All was fine before update 9 I need a lead on where can I change the MAC after boot and autoload the r8168 module on boot. Jun please help. ** EDIT ** Kinda solved it. 1. removed any reference to MAC addresses from the GRUB config. 2. found out that "ifconfig eth2 up" brings up the device and it works. 3. created a startup script that will activate the module on boot and bring up the device. admin@XXXXXX:~$ cat /usr/local/etc/rc.d/S99realtek_fix.sh #!/bin/sh echo "loading r8168 module" insmod /usr/lib/modules/update/r8168.ko echo "bringing device up" ifconfig eth2 up 4. updated to Update 9 and it's works. 5. I will never EVER install updates when they come out, I will wait! Hope this will help somene, And hope that a developer can figure out why is this module and possibly other are not loading on boot.
  4. komarto

    DSM 6.1.x Loader

    does you NAS have a static IP or DHCP?
  5. komarto

    DSM 6.1.x Loader

    SSH Is working?
  6. komarto

    DSM 6.1.x Loader

    Did anyone tried the new patch?
  7. komarto

    DSM 6.1.x Loader

    That did the trick, I baby-stepped the updates one by one, all is working well!
  8. komarto

    DSM 6.1.x Loader

    i have downloaded "synology_bromolow_3615xs.pat" from the link and the update fails...
  9. komarto

    DSM 6.1.x Loader

    did you manage to install the update?
  10. @quicknick my board has 4 SATA ports which are populated: 1 x 60gb SSD for system 3 x 3TB RAID5 for data I also have a Marvell 88SE9215 SATA III 4 port addon card which right now has no drives attached, how should I configure my Sata Port Map, just enter 4? Do I have to do that again if add drives to the addon card? also is my card (Marvell 88SE9215) supported, could not figure that out based on the drivers section on your first post? Thank you for time and effort, Komar
  11. Then you haven't read the instructions till the end. I recommend you do so as what you are asking is clearly addressed in the tutorial. I read it, again, still do not see any info regrading the above. something else, I enabled my Realtek NIC and now I can find the NAS, which means that the loader does not have drivers for my Intel 82580 NIC only for Realtek, Posted Here a driver request. do you know if Marvell 88SE9215 SATA controller driver is also included? also when I find my NAS I get SATA disabled, I tried SataPortMap=44, I have 4 onboard SATA port and 4 more on a MAREVL expension card, can you help?
  12. komarto

    Drivers requests for DSM 5.2

    loader for v6 does not seem to recognize my intel 82580 NIC and does Marvell 88SE9215 SATA controller driver is also included?
  13. Hi, Followed the instructions but all I get is the screen will stop updating shortly... and not: early consol in decompress_kernel Decompressing Linux.. Parsing ELF… done. Booting the kernel. what am I doing wrong?
  14. komarto

    CPU Throttle Script Tutorial

    Hi, please run : cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors this will show you available governors, then select the one you like and edit the script. there are 2 governors because this kernel uses intel_pstate