yongbi

Members
  • Content count

    12
  • Joined

  • Last visited

Community Reputation

0 Neutral

About yongbi

  • Rank
    Newbie
  1. yongbi

    DSM 6.1.x Loader

    But if i migrate my current SHR raid to this dsm version, when i edit the synoconf it's after installation so would it wipe my data or will it boot nonetheless but just won't show it as SHR in the storage manager ? And so i install dsm 6.0, i edit synoconf, reboot and voila all is good ?
  2. yongbi

    DSM 6.1.x Loader

    So far I have migrated 4 of this from v5 to v6 you need to change de vid/pid and then edit synoinfo.conf to enable SHR, so far I have been able to expand with no problems, to edit synoinfo.conf you must ssh and then follow this to enable SHR with sudo: edit /etc.defaults/synoinfo.conf comment out/delete CODE: SELECT ALL supportraidgroup="yes" then add CODE: SELECT ALL support_syno_hybrid_raid="yes" Thanks for those infos, i didn't even know SHR wasn't supported natively. Is it over with DSM 6.0 or just a "bug" in this loader ?
  3. yongbi

    DSM 6.1.x Loader

    I need to clear one last detail before updating, anyone can confirm if creating new disk group is working ? Also can you expand volume ? If anyone tested i would like to know.
  4. yongbi

    DSM 6.1.x Loader

    Just upgraded my N54L. You need to ensure you delay first menu Timeout to 5 sec. so you can select the AMD boot. Just set VID and PID (and MAC/Serial if needed). No Sata port settings required. Thanks I will try it out. Do you need to select it at each boot or only for the first installation ?
  5. yongbi

    DSM 6.1.x Loader

    http://terfmop.co.uk/blog/2013/07/31/hp ... sata-port/ From the main screen go to ‘Chipset > Southbridge Configuration > SB SATA Configuration’ and make sure your settings are the same as below: OnChip SATA Channel = Enabled SATA PORTS 4/5 IDE mode = Disabled SATA EPS on all PORT = Enabled SATA Power on all PORT = Enabled Return to the main screen then go to ‘Advanced > IDE Configuration’ and again, make sure your settings are the same as below. Embedded SATA Link Rate = 3.0Gbps MAX The above was taken from viewtopic.php?f=2&t=1316&start=30#p6904 I did that years ago, i meant the sata option for this new loader, sataportmap or so. I have already the 5 disks since long.
  6. yongbi

    DSM 6.1.x Loader

    I have looked everywhere on the internet and in my hp gen7 specs, i can't find how to configure the sata option for the N54L with 5 disks installed. Is there a risk to test several ? Like 41, 50 or 401 ?
  7. yongbi

    DSM 6.1.x Loader

    Did you need to modify the sataport setting ? also how many disks are you using on your N54L ? I'm using 5 (4+ the optical drive slot). I'm asking cuz i can't really backup all my data as i have 30 TB but i would like to migrate to DSM 6 and be certain the risks are limited.
  8. yongbi

    [Résolu] Impossible d'étendre le volume

    J'ai le même souci sauf que la commande lsof ne fonctionne pas pour moi, ton diskstation était bootstrappé, est-ce un ipkg ???
  9. yongbi

    Nouvelle Maj 5.1.5004

    Oui j'avais laissé tous mes paquets. J'ai juste eu besoin de refaire le bootsrap
  10. yongbi

    Nouvelle Maj 5.1.5004

    Moi j'ai gardé toutes mes data et j'ai même gardé tous les réglages (pas de clean install) J'étais en 5.0 4096 j'avais pas updaté à la première release ratée
  11. yongbi

    Nouvelle Maj 5.1.5004

    Plus de 24 h apres. Toujours pas de pb
  12. yongbi

    Nouvelle Maj 5.1.5004

    5.1 Update 1 sur Proliant N54L sans problème même en choisissant garder les paramètres, rien eu à réinstaller à part le bootstrap et mon ps3netsrv Tous mes packages fonctionnent aussi bien les classique DS que sabnzbd, couchpotato, sickrage, ... Plusieurs reboot au total mais bon le principal c que ce soit fait. On verra si j'ai encore accès à mon volume dans 24 heures xD (cf précédent bug)