Jump to content
XPEnology Community

serdar13

Transition Member
  • Posts

    11
  • Joined

  • Last visited

Everything posted by serdar13

  1. I have just tried installing DSM 6.1.7-15284 and it has worked on internal NIC and pci card. Updated to DSM 6.1.7-15284 Update 3 too. Unsure what is missing to to get 6.2.3 working.
  2. I am trying to install 6.2.3 as a clean install and followed guides however cannot get N54L to be seen on network to apply corresponding .pat file. I have tried internal NIC as it is supposed to be working on 6.2.3 and Realtek RTL8111E card i have installed in it too. Added VID and PID and mac address's and s/n, I am going crazy as i have 4 similar servers working just fine. Using 'Jun's Loader v1.03b DS3615xs'. Any suggestions will be appreciated
  3. I wish i could but when you said it was not possible with my setup i sold the GPU. Wish I kept it now as looks like IG-88 was onto something.
  4. So are you stating that using 3615 on my microserver i can use the P1000?
  5. Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 5.2-5967 update 9 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: BAREMETAL - HP Microserver Gen8 - Additional comment: Clean install | reboot required | onboard NIC recognised | had to run sudo rm -rf /.xpenoboot to get network settings working after migrating data
  6. I direct stream with all devices at home but I would like my dad to see some movies too so is reliant on lower quality streams as he will be accessing my library over the internet. I will try out DS916+ but i am not expecting much so therefore will sell the GPU and thus use my processor within its limits.
  7. Flydrive, thanks for confirming what I assumed. If i did use for example DSM 6.1.7 for DS916+ then would this version of DSM support my CPU and GPU? If so, how great would it be? I know there is no further support for DS916+ but i am still using DSM 5.2-5967 Update 9 for ages now and instead of jumping to 6.2.3 i could just use 6.1.7 if it meets my needs.
  8. Hi guys, I have been searching the forums and was cannot find what i am looking for. Basically I have a Microserver Gen8 with a a Xeon E3 1265L v2 processor and a Nvidia Quadro P1000 and wanted to know how to get Hardware and Software acceleration working for transcoding purposes when i use Emby. I have been testing DSM 6.2.3_25426 (DS3615xs) and all seems good but before i upgrade my drives from DSM 5.2 wanted to test acceleration. Should i be using a different loader/version of DSM e.g DS918+ ? How do i get the /dev/dri folder people mention? Any help or a link in the right direction would be great.
  9. Just installed DSM 6.2.2-24922 Update 6 successfully on my Gen8 (with extra.Izma) as a test before i commit as i am still running 5.2-5967 Update 9 which is very stable for me. All looked good but has anyone had success in bonding the x2 internal NIC's? The internal NIC's were working fine as 2 seperate NIC's in DHCP mode and with Static IP's but once Bonded together in Link Aggregation Mode i am not getting an IP address to connect to it. Synology Assistant can see server but with following detials: (MAC address 1) Nothing = IP address Manual = IP status Status = Ready (MAC address 2) Nothing = IP address Manual = IP status Status = Connection failed It seems the DSM software tried to bond the network ports but something is not right somewhere. I tried a re-install and same thing happened. Therefore was wondering if anyone else had success in Bonding the NIC's?
  10. - Outcome of the update: SUCCESSFUL - DSM version prior update: Clean Installation - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: YES (1.03b_mod ds3615 DSM 6.2.2 v0.5_test) - Installation type: BAREMETAL - HP Microserver Gen8 - Additional comment: manual reboot required | Internal NIC's recognised but once Bonded together in Link Aggregation Mode, no IP address created.
  11. Hi, i am trying to get this to work under DSM 5.2 on a Microserver Gen8 but getting the following error when running 'ch_cpuinfo.sh': "DSM CPU Information Change Tool ver. 2.2.1-r01 - made by FOXBI DSM version less than 5 is not supported. End the process." Is anyone able to help?
×
×
  • Create New...