Zippi

Transition Members
  • Content count

    6
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Zippi

  • Rank
    Newbie
  1. Hello everyone, I get this : I had just wrote this but i only say what happened, I use a E350-M1 motherboard I've Xpenology installed on the machine I prepared to use as NAS . I installed 2 WD RED 4 TB connected to the SATA ports 1 and 2 of the motherboard . They are regularly recognized by the bios of the motherboard in positions 1 and 2 Xpenology sees the disks in positions 1 and 3 . If you exchange the SATA cables of disk 2 and 3 Xpenology correctly sees the HDDs in the 1 and 2 positions but in the bios on the motherboard of course find them on 1 and 3 . In practice, the HDD connected on SATA1 is seen in position 1 , SATA 4 in position 4 , while 2 and 3 are only reversed on Xpenology but not on the motherboard and bios . It ' happened to any of you ? It ' a Xpenology firmware bug ? I only use SATA ports on motherboard Thanks to those who want to help me ! Zippi . P.S.: Excuse me for my poor english!
  2. Zippi

    Disc 2 and 3 inverted

    OK, thanx to all...... My goal is to set up a 4 disks NAS in RAID 5 with 4 WD RED 4TB I can leave the 4 disks in the right position seen correctly from the mobo, i just gotta remember that i have disk 2 and 3 inverted. The system will work well? ( RAID 5 with 4 disks ) I will install the disks in a 4 slots backplane. THX again....
  3. Zippi

    Disc 2 and 3 inverted

    ah, ok..... if I had put 4 discs at once I would not have noticed because I saw 4 discs regularly. Then it will work all the same ?
  4. Zippi

    Disc 2 and 3 inverted

    Hello everyone, I get this : I use a E350-M1 motherboard I've Xpenology installed on the machine I prepared to use as NAS . I installed 2 WD RED 4 TB connected to the SATA ports 1 and 2 of the motherboard . They are regularly recognized by the bios of the motherboard in positions 1 and 2 Xpenology sees the disks in positions 1 and 3 . If you exchange the SATA cables of disk 2 and 3 Xpenology correctly sees the HDDs in the 1 and 2 positions but in the bios on the motherboard of course find them on 1 and 3 . In practice, the HDD connected on SATA1 is seen in position 1 , SATA 4 in position 4 , while 2 and 3 are only reversed on Xpenology but not on the motherboard and bios . It ' happened to any of you ? It ' a Xpenology firmware bug ? Thanks to those who want to help me ! Zippi . P.S.: Excuse me for my poor english!
  5. Zippi

    Disco 2 e 3 risultano invertiti

    Buongiorno a tutti, mi capita questo: Ho installato Xpenology sulla macchina che ho preparato da utilizzare come NAS. Ho installato 2 dischi WD RED da 4 TB collegati alle porte SATA 1 e 2 della piastra madre. Sono riconosciuti regolarmente dal bios della piastra madre nelle posizioni 1 e 2 Xpenology vede i dischi nelle posizioni 1 e 3. Se scambio i cavi SATA sui dischi Xpenology vede correttamente gli HDD nelle posizioni 1 e 2 ma nel bios della piastra madre ovviamente li trovo su 1 e 3. In pratica l'HDD collegato su SATA1 è visto in posizione 1, SATA 4 in posizione 4, mentre 2 e 3 sono invertiti solo su Xpenology ma non sulla piastra madre e nel bios. E' capitato anche a qualcuno di voi? E' un bug del firmware Xpenology? Grazie a chi mi vorrà aiutare! Zippi.
  6. Zippi

    Aggiungere HDD su ASROCK E350M1

    Ciao a tutti! Volevo chiedere a chi ne sa più di me....... Ho implementato un sistema XPEnology su una motherboard ASROCK E350M1 con 4 porte SATA 3. Mi chiedevo: se dopo aver installato 4 HDD e configurati in RAID 5 dovessi aggiungere un altro HDD come posso utilizzarlo? Avendo finito le porte SATA posso aggiungerlo su USB ma lo vedrà come HDD esterno o posso aggiungerlo al raid come ad esempio si può fare con OMV? Grazie a chi mi può aiutare! Zippi.