Jump to content
XPEnology Community

Gryllz

Rookie
  • Posts

    6
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Gryllz's Achievements

Newbie

Newbie (1/7)

0

Reputation

  1. Hi, I am running 6 drivers which is I guess maximum for this MB and its possible lines. If remember correctly last two 2 sata ports I was adding are sharing 6Gbit troughput which is still higher than what drivers I use are capable so I am good. , Like it has been say if DSM recognize them... (I was selecting adapters carefully to have chance for better compatibility by reading all treads on this forum related to native hw installations)
  2. YEAH! disable VT-d in bios did a trick! Thank you very much @IG-88 you are hero of my day I have only remaining issue that disk is diffent size and brand and for some reason I cannot add it from Action button add disk to already existing 4 disk pool, is that by design or can I hack this somehow? at least is visible under the disk list now and as available and I can create new pool from it ...
  3. Yes I do have Asrock J5040-ITX. I found these in report, it seems affected is ata3 and 4 because of the errors in the report: I am not sure how to troubleshoot this. I am still Nob here. [ 2.296609] ata3: SATA max UDMA/133 abar m2048@0xa1210000 port 0xa1210100 irq 123 [ 2.296623] ata4: SATA max UDMA/133 abar m2048@0xa1210000 port 0xa1210180 irq 123 [ 2.301968] DMAR: DRHD: handling fault status reg 2 [ 2.302300] DMAR: DMAR:[DMA Write] Request device [01:00.1] fault addr fffe00 00 DMAR:[fault reason 02] Present bit in context entry is clear [ 2.354380] sdb: sdb1 sdb2 sdb5 [ 2.355203] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.600704] DMAR: DRHD: handling fault status reg 2 [ 2.601078] DMAR: DMAR:[DMA Read] Request device [01:00.1] fault addr fffe000 0 DMAR:[fault reason 02] Present bit in context entry is clear [ 2.750883] clocksource: Switched to clocksource tsc [ 12.294652] ata3: softreset failed (1st FIS failed) [ 12.300762] DMAR: DRHD: handling fault status reg 2 [ 12.301139] DMAR: DMAR:[DMA Write] Request device [01:00.1] fault addr fffe00 00 DMAR:[fault reason 02] Present bit in context entry is clear [ 12.599602] DMAR: DRHD: handling fault status reg 2 [ 12.599981] DMAR: DMAR:[DMA Read] Request device [01:00.1] fault addr fffe000 0 DMAR:[fault reason 02] Present bit in context entry is clear [ 22.293616] ata3: softreset failed (1st FIS failed) [ 22.299522] DMAR: DRHD: handling fault status reg 2 [ 22.299897] DMAR: DMAR:[DMA Write] Request device [01:00.1] fault addr fffe00 00 DMAR:[fault reason 02] Present bit in context entry is clear [ 22.598564] DMAR: DRHD: handling fault status reg 2 [ 22.598929] DMAR: DMAR:[DMA Read] Request device [01:00.1] fault addr fffe000 0 DMAR:[fault reason 02] Present bit in context entry is clear [ 57.287482] ata3: softreset failed (1st FIS failed) [ 57.287859] ata3: limiting SATA link speed to 3.0 Gbps [ 57.297589] DMAR: DRHD: handling fault status reg 2 [ 57.297958] DMAR: DMAR:[DMA Write] Request device [01:00.1] fault addr fffe00 00 DMAR:[fault reason 02] Present bit in context entry is clear [ 57.592433] DMAR: DRHD: handling fault status reg 2 [ 57.592807] DMAR: DMAR:[DMA Read] Request device [01:00.1] fault addr fffe000 0 DMAR:[fault reason 02] Present bit in context entry is clear [ 62.287468] ata3: softreset failed (1st FIS failed) [ 62.287837] ata3: reset failed, giving up [ 62.592411] ata4: SATA link down (SStatus 0 SControl 330) [ 62.592418] ata4: No present pin info for SATA link down event [ 62.593065] ahci 0000:04:00.0: SSS flag set, parallel bus scan disabled [ 62.593112] ahci 0000:04:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 imp
  4. Hi @IG-88 sorry for probably stupid question but is it so this AHCI driver for Marvell 88SE9125 is part of 3615/17 loader only? I am bit stuck with J5040 and Marvell 88SE9125 when I run 918+ I cannot utilize additional 2 disks except onboard controller properly and I don't know where to else to look in this forum. Funny is that it seems recognize somehow in drives numbers because it skipped 3. and 4. as you see: I will appreciate any help here, since the same controller worked with FREENAS / TRUENAS native OS but I want to use 5 drives in one LUN and have 6. drive for backup purpose what is not supported by ZFS (only in pairs which wont be fitting my usecase) Best Regards! Gryllz
  5. Hi, can you please add Marvell 88SE9125 to 918+ loader, so I can configure 6 drives (4 drives discovered with build in controller) with ASROCK J5040 which have only 1lane on PCIe avaialble so only two ports are possible too feed with good throughput if I did a math properly. * I don't understand why drive 3 and 4 is missing here ... or is it well hidden? not sure if drivers discussed here: https://xpenology.com/forum/topic/14127-guide-to-native-drivers-dsm-621-on-ds918/?do=findComment&comment=145203 has some other HW requirements, but I didn't see any miracle with my DSM. not sure if this link with driver is the right one, but someone refered to this in previous comments with tread I just shared. https://linux-hardware.org/index.php?id=pci:1b4b-9125-1b4b-9125 Thanks in advance! and thanks for all great work or efforts so far.
×
×
  • Create New...