MSXGames

Hi, I have tested the RS4021xs+ version on a Dell R320, Intel E5-2450L V2 with 48Gb ram, 4x 2Tb HDD, sata (no hardware raid controller) and the standard broadcom network cards. The version DS3622xs+ is working fin on the system. When installing version RS4021xs+, it will not find the server. tested with TCRP and ARPL Without bringing the friend and with bringing the friend over. When installing RS3618xs, the server can be found, but installing DSM will give and error, a corrupted file. Anychange I am doing it wrong or the version are not suitable for the Dell R320 Kind regards

Hi, Thank you so much for this. Finally I got it to work and it even can be updated to update 3. It took me a while to have it working, but your solution is great and works after a few installation steps. It works on the AMD system. Kind regards

I have tried to install DS923+, but I get an error when building the image: I do not know what is going wrong, if I am correct, the error is about the realtek ethernet chip, is that correct? I did a full update (it updated to 0.9.4.3) and a full upgrade as well. Kind regards

Hi, Sure I want to try the model DS923+ But I think it is not in TCRP (redpill) of PocoPico right ? I also have tried without FRIEND, still same issue

Hi All, I have a pc with an AMD A4-5000 APU, with a Realtek RTL8111E network card. With version DSM 7.0.1 it was running fine, after a update to DSM 7.1.1, it looks like the network card is not running. I have tried withfriend and if it is booted I see a ip adress, but when I type that IP address it is not going to DSm, also tried with find.synology.com, same issue, the server is not responding. I have used DS1621+ aswell DS2422+ Any ideas ? Do I need to add some extensoin? I have tried with a clean install, so removed the hard drives and put empty in the system. I have tried with EUFI and Legacy mode (No UEFI), same issues Kind regards

@Peter Suh Yes you are correct, the model RS3621xs+ is a dual power station, my bad, I thought this one was a single power station. Then this model is not good to make a TCRP version. ALmost all versions are with two power supply's. Only the AMD versions has one power supply, will take a look for a model, because the 3618 model is 4 years old now. Thank you for pointing me about the two power supply's Kind regards

Hi @pocopico I was thinking about the RS3621xs+, that has a 8core intel xeon cpu and 12 bays. And because I am running it on a server in a rack, the name makes it a little bit easier. It also can handle up to two 10Gbit ethernet cards. I know we can run DS3822xs+ on a server (I am running one as a bare metal), but because of the name RS (Rack System) makes it a bit easier. If you can add and it is possible, I will appriciate it very much. Thank you Kind regards

Hi All, @pocopico In TCRP we have a lot of DS models. Is there also a RS model coming in TCRP ? Kind regards

Hi All, I have a question, I couldn't find it so hopefully someone can answer it. I have a Dell R210 II with Broadcom network adaters, the server starts and TPRP is starting, but it will not connect to the internet, even when the cable is connected. I have put in a Intel i225 (2.5 Mhz) netwerk card in the server, the server start and TCRP is loading, but no internet connection. When I do lspci -nnq I see all the network adapters in the list (broadcom and intel i225). Are these network adapters not loaded or are there no drivers ? Thank you.

Check if yout ime setting are okay. I had this issue once, when done a time setting all was fine. You can use the sync button.

Thank you for the tip and explanation. I do not use a raid card, not on the SuperMicro or the Dell server for this test. I know you need it in IT mode, but the sata ports are fast enough, so I do use the build in sata controller. If the satamap is on 6, DSM does not see any drives and sata is off. But if I use 46 in the satamap and diskid 0000 as I mentioned before, all sata ports are active and I can use the drives.

Hi All, First of all, thank you @pocopico and @Peter Suh Here are my findings. Last week I was testing to install DSM 7.0.1-42218 on several machines. First I used a SuperMicro server with an Intel Xeon L5630 cpu and 24Gb of ram. So far so good, I could install version 7.0.1-42218 and installation is successfull. After reading a lot posts over here, I tried to upgrade from 7.0.1-42218 to 7.1.0-42661 and it failed using the instruction of @Peter Suh Even if I first installed 7.0.1-42218 complete and then upgrade, it failed, keeps nagging about corrupt file. When I tried to do a fresh install, samething, keeps nagging about corrupt file, even when I downloaded the file from the cache on TC, same thing. The following instructions was entered: Then after hours of trying I used the Dell R320 to give it a try. Installing DSM 7.0.1-42218, perfect it runs and see all the drives. The did a full wipe (so to have a clean installation, even drives where wiped). Entered the instructions as noted by @Peter Suh And it starts up to DSM 7.1, but just with one drive (no other sataport/drive where found). Again, started to TC, did a clean instruction and changed the satamap to the following: "SataPortMap": "46", "DiskIdxMap": "0000" rebuild everything again with ./rploader.sh build broadwellnk-7.1.0-42661 rebooted the server and started to DSM 7.1, did the installation steps en all drives where found. It looks like something about which components you use ? With every server I used, I have changed the mac adres to the mac adres from the nic's I have installed now DS918+ on an asrock motherbord with an Apollo Lake cpu on it running DSM 7.0.1-42218 Will try to do an upgrade to DSM 7.1.0-42661 next time and will write to outcome here. Thank you for reading this post Kind regards

@pocopico and @altas Well, I have checkt with a vpn connection to an other country, and the the site is working and redpill is working. Now checkt it with vpn on and installing thru the app and it is working, slow yes, but it is downloading it. Sorry for the inconvience and thank you for the help. Still I do not know what the problem is, but he, it worked now.

Okay, thank you for the answer

@pocopico I have ask it several times? Is it possible to change the download path dor the .pat files to https://global.download.synology.com/download/DSM/release/7.0.1/42218/DSM_DS3622xs+_42218.pat I am trying to install DS3622xs+, but it will not download from https://cndl.synology.cn/download/DSM/release/7.0.1/42218/DSM_DS3622xs+_42218.pat Thank you very much!! ps: I know I have ask several times in this threath, but still no answer.