Jump to content
XPEnology Community

askyz

Rookie
  • Posts

    3
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

askyz's Achievements

Newbie

Newbie (1/7)

0

Reputation

  1. - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.3-25426 Update3 - Loader version and model: Jun's Loader v1.04b - DS918+ - Using custom extra.lzma: YES (v0.13.3 by IG-88) - Installation type: BAREMETAL - ASUS TUF B365M-PLUS-GAMING - i3-9100 - Intel® I219V - Intel® I350T4V2 - Additional comments: Reboot, HW transcode is still working in Plex
  2. Okay, now I think I know where the problem is. It seems to be in bond mode. I changed the current bond mode from the original SLB to the current active-standby mode. VMM works and can create virtual machine clusters normally. However, there is still a strange problem. When network ports> 4, the 5th network port still cannot recognize the real mac address. But it does not affect my use now, and I just updated 25426 update3, everything seems to be fine. Both my read cache and hardware transcoding are available.
  3. Hello everyone, I am building my NAS recently, and I have referenced a lot of IG-88 before that. Now, my NAS seems to be perfectly supported for the hardware part. hardware list below: CPU: i3-9100 Motherboard: TUF-B365M-PLUS-GAMING (1LAN i219-V) (6-SATA3 ports) Memory: Kingston DDR4 2666 (8GB*2) PCI-E x4: JMB585 (5-SATA3 ports) PCI-E x4: Intel-I350T4v2 (4-LAN) M2.NVME.SSD: WD NS750-256GB (cache) SATA.SSD: Samsung 860 EVO 500GB (os and software) SATA.HDD: Seagate 8*8TB (ST8000VN004 raid-5) Driver extension jun 1.04b for DSM6.2.3 for 918+_25426 update 2 and extra918plus_v0.13.3 to replace extra.lzma/extra2.lzma What settings did I modify? 1. I used a 16GB USB for booting and modified the vid and pid in the grub.cfg file. 2. And I also modified the SN and mac addresses in the grub.cfg file, because I have 2 network cards and 5 network ports, so I think I should do this, although 918+ only supports 2 network ports by default. set mac1=XXXXXXXXXX7D // onboard network card i219v set mac2=XXXXXXXXXXC0 // pci-e network card i350 T4v2 set mac3=XXXXXXXXXXC1 set mac4=XXXXXXXXXXC2 set mac5=XXXXXXXXXXC3 Here I fill in the real mac address on my network card. And the IP address can be scanned after booting. 3. I modified the synoinfo.conf in the /etc and /etc.default/ maxlanport="2" >maxlanport="5" Add content: eth3_mtu="1500" eth3_wol_options="d" eth4_mtu="1500" eth4_wol_options="d" eth5_mtu="1500" eth5_wol_options="d" 4. In order to use the 918+ read cache, I replaced the libsynonvme.so.1 file in the /usr/lib64 directory chown root:root libsynonvme.so.1 chmod 644 libsynonvme.so.1 Modify users and groups and file permissions to make it consistent with the source file After I installed the DSM system, I encountered several strange problems. 1. Because I don't have a synology account, every time I install software such as plex, video station, photo station, audio station and etc, the browser will time out and ask to log in again. 2. I enabled bond technology on DSM, only using SLB. Because my switch does not support LACP, but the bond0 network card does not use my real mac address, bond0 should use the real mac address of eth0 under normal circumstances, and the current mac address is never set. I use the ifconfig command: bond0 Link encap:Ethernet HWaddr XXXXXXXXXX56 // not real mac ----used eth0 Link encap:Ethernet HWaddr XXXXXXXXXXC0 // real mac ----used eth1 Link encap:Ethernet HWaddr XXXXXXXXXX56 // not real mac ----used eth2 Link encap:Ethernet HWaddr XXXXXXXXXXC1 //real mac ----unused eth3 Link encap:Ethernet HWaddr XXXXXXXXXXC2 //real mac ----unused eth4 Link encap:Ethernet HWaddr XXXXXXXXXXE1 //not real mac ----unused As you can see, under normal circumstances, because I specified the real mac address in the grub.cfg file, after setting bond0 for eth0 and eth1, bond0 should use the mac address of eth0 or eth1, and the unused network port should be real mac address. just like below: bond0 Link encap:Ethernet HWaddr XXXXXXXXXX7D // bond0 used eth0 Link encap:Ethernet HWaddr XXXXXXXXXXC0 // i350-T4v2 used eth1 Link encap:Ethernet HWaddr XXXXXXXXXX7D // i219v used eth2 Link encap:Ethernet HWaddr XXXXXXXXXXC1 //unused eth3 Link encap:Ethernet HWaddr XXXXXXXXXXC2 //unused eth4 Link encap:Ethernet HWaddr XXXXXXXXXXC3 //unused But the current situation is that a wrong mac address appears after bond0, which causes the mac address of eth1 to be wrong, eth4 is an unused network port, and the mac address is also wrong. 3. Because the mac address inside DSM is inconsistent with that in the grub.cfg file, I tried to install the VMM software of DSM and enable the open-switch function, but when creating a virtual machine cluster, an error occurred. I searched a similar question from google, but did not find an accurate answer, so I guess it is related to the match of the mac address. Attached is the /var/log/messages log, errors related to installing VMM and creating virtual machine clusters. I'm not sure I can find the answer, but I want to share it. Sorry that my English is not very good and it is useful for translation software, but I hope to express my problem and the specific situation of my operation as much as possible. messages.txt
×
×
  • Create New...