MikeD

Members
  • Content count

    15
  • Joined

  • Last visited

Community Reputation

0 Neutral

About MikeD

  • Rank
    Newbie
  1. I use pyload as downloader. There is an good android app for controlling and adding downloads. If you use esxi you can install Xpenology and Windows/Linux of course. Only bottleneck is your hardware. I think most important is to have enough RAM for every VM. Then you can run as much as you want. But I'm not sure if you can directly use your hard drives. I think you have to backup all your data and restore it after setting up Xpenology as VM.
  2. 32MB I guess. Just for Xpenoboot image.
  3. Xpenology as a virtual machine is more complicated to install. So if you don't want to run other OS than Xpenology parallel on same server just install it directly with USB stick. With direct install speed might be better (compared to sharing resources with other VMs) but you could have higher fan noise. Be sure to have latest drivers installed for lowest fan noise.
  4. I don't know how the installation process on N54L but you will not have any problems with Gen8. You could install Xpenology as virtual machine or directly.
  5. [Solved] Unable to install pyload on Xpenoboot

    No, working fine here in ESXi. Have also installed python package before?
  6. HP Microserver Gen8 Esxi USB Passthrough

    Right now it's also not working for me. But I will have a look at it in the next days. Maybe a BIOS Update and some BIOS configuration would help. I will let you know if I get it to work.
  7. HP Microserver Gen8 Esxi USB Passthrough

    That's normal. I have the same message there. This is something different I guess... Look at the link I have posted. Read on from point 3 at section beginning with "The next step is..." Same way you have added the controller you have to add the single devices.
  8. HP Microserver Gen8 Esxi USB Passthrough

    I also use ESXi 5.5 and the processor G1610T. I only named the VM "Diskstation 5.0". Do have added the USB-Controller to your VM-configuration? Then you could plug in an USB device in e.g. front USB and you should be able to add an USB device in the VM settings. You understand that you have to manually add any new usb device the first time in the vm configuration to get it working in DSM? Atm I don't have time to boot into BIOS settings.
  9. HP Microserver Gen8 Esxi USB Passthrough

    You have to change the the configuration of your DSM VM with vSphere client. There you can add usb devices. For me only the 2.0 ports (2 front, 2 back) are currently working. Maybe I should have a look in BIOS to activate the 3.0 ports. And I think you have to add first an USB-Controller. You can have a look here for instructions (from point 3): http://www.v-front.de/2014/11/vmware-silently-adds-native-usb-30.html This is my personal config with working passthrough.
  10. Ok, dank dir schon mal. Damit muss ich mich dann mal auseinander setzen, wenn ich wieder etwas mehr Zeit habe. Ich würde natürlich gerne noch versuchen etwas Strom zu sparen und SMART wäre auch sehr gut. Vielleicht teste ich auch nochmal Xpenology im AHCI Mode ohne ESXi. Da hieß es allerdings, dass der Lüfter lauter dreht.
  11. Also USB und Kartenleser laufen auch über den Controller? Zur Not müsste ich mir mal einen zweiten kaufen. Hätte ja einen Steckplatz frei...
  12. Mit dem integrierten läuft das nicht?
  13. Ich häng mich dann auch mal rein. Würde gerne auch auf meinem HP ProLiant Microserver (Gen8) gerne Hibernation und SMART nutzen. Sobald ich Zeit habe, versuche ich mich mal daran. Es hat nicht zufällig jemand auch den Gen8 und das schon hinbekommen?
  14. Ok, I think I got the solution. After updating on 4493-Update3 the expanding this time goes into the next step (adding hdd) and didn't stop at mounting hdd. Gesendet von meinem LG-D802 mit Tapatalk
  15. I tried to expand my SHR Volume (2 disks) with another one and it failed. I have a HP Microserver ProLiant Gen8 with ESXi 5.5 und and raw-disk-mapped the hdds to the VM Xpenology DSM 5.0-4493 Update 2 (nanoboot). The log says: Jul 29 12:23:59 HP volumehandler.cgi: space_internal_lib.c:309 Failed to migrate '/dev/md2' from RAID 1 to RAID 5 Jul 29 12:23:59 HP volumehandler.cgi: space_internal_lib.c:568 Failed to migrate RAID 1 to RAID 5: [/dev/md2] with disk [/dev/sdc5] Jul 29 12:23:59 HP volumehandler.cgi: space_shr_add_disk.c:53 failed to add partition to space: /dev/vg1000/lv [0x0D00 string_sep_pair.c:54] Jul 29 12:23:59 HP volumehandler.cgi: space_expand.c:323 failed to add disk into SHR. Jul 29 12:23:59 HP volumehandler.cgi: space_lib.cpp:1423 failed to expand space: /dev/vg1000/lv [0x8000 space_expand.c:322] Jul 29 12:23:59 HP volumehandler.cgi: volumehandler.cpp:546 failed to expand space: /volume1 Can maybe somebody confirm that the process described in the first post could help me?