merve04

oh for sure they are, were always in use during the conversion.

I use a gigabyte b365m board and I have lsi 9211-8i in IT mode. Everything works OOB. that gives me 14hdds at the moment, but will eventually get another Lsi card, probably the 9xxx-4i version as it’s a pci 4x card which is all that’s left on my mobo.

what are you using on xpeno as streaming host?

Alor jai fait linstallation de limage 918, fonctione bien, mais 3615 ne fonctione pas. est-ce possible davoir les deux en meme temp? ou cest un ou lautres?

jai trouver le probleme, lorsque je decompressait le fichier sur un mac, il devenait un dossier avec 3 fichier, alor jai transfere le zip sur le nas puis maintenant jai le fichier ova.

Petit probleme, jai telecharger les 2 fichier DSM-6.2.2_ds918_OVA et DSM-6.2.2_ds3615_OVA, mais a linterieur, il y a aucun fichier ova, alors ce nest pas possible d'importer la configuration dans VMM. Ill y a tu un truc que je ne suis pas au courant? merci

Tu peux toujours utiliser VMM et installer une autre instance de xpeno et ajouter 2 autre camera ip.

Just thought I'd give an update, so after the expansion of the 8TB was completed, i rebooted system, and under volumes, configure was now available and was able to max the amount of free space from the storage pool. All 40TB now available and slowly filling up

Ok I’m a little bit of a novice when it comes to Linux stuff but not afraid to follow a tutorial. I will wait till the 8TB is finished being added to the pool and see what the end result is then. If new storage is still not being added correctly, I will try and gather some info from your commands first and report back with some screen grabs. thanks for the help.

Thanks for the reply. Yes 100% it was done, cat proc/mdstat showed everything operating as normal, nothing in progress or delayed. The storage pool I expanded only has 1 volume created in it. As mentioned, I’ve now started expanding the same pool with a 8TB now, will take a bit of time as there’s 2 stripes to expand this time. I use ext4. Would your command be as easy as replacing “btrfs” with ext4 in place?

So I'm confused as to why I haven't seen an increase to my volume. Im running SHR-2, I had 4x 8TB and 4x 4TB drives, which resulted in 29TB, I then expanded with a 4TB and DSM estimated 32TB after completion. The storage pool does indeed state 32.72TB in size, 3.63TB available, but under volume, there's no option to add\configure the extra capacity, only create a new volume. I've now added a 8TB, so once again its expanding and estimates 40TB once completed. Any advice?

So I have gigabit, when I use download Station, no VPN, I tend to hit 40-60MBps, with my VPN on (ExpressVPN) 20-25MBp. On my desktop, when I run Speedtest, I hit 940-960Mbps both directions, but even downloading from the very best servers like Microsoft for example, 70-80MBps max not sure why nas is slow like that, could it be HDD writing speed? I would think it can handle more than 60MBps?

It finally finished at about 1068 hours. It was an extremely slow process avg 1200-1500kbps. im now expanding my volume with couple hard drives, first one in and at roughly 25% after 8 hours.

Ive done L2TP/IPSec and OpenVPN.

If i go in my control panel, under network, general tab, (this applies when my VPN is connected) my default gateway is the VPN, followed by my local network, advance settings, both options are checked on. In regards to the settings of my VPN, theres 4 check mark boxes available, i use the first, second and fourth.

Free tends to be unreliable, I think most that use VPN's may recommend NordVPN or ExpressVPN.

Very strange. I’ve used ExpressVPN in my synology for over a year, no issue. Maybe delete your VPN profile, uninstall download station and try to reconfigure.

864 hours, 71%.

Currently have LSI 9211-8i + sata onboard sata ports. Looking to expand, unfortunately I didnt know about the 9201-16i at the time as perhaps i would of plunged for that card. Also I only have 1 16x pcie port. I do have a couple 1x and 1 4x slot. I came across a LSI 9211-4i, I'd assume its the same as my current card, just one sas port. Or are run of the mill 2port\4port sata cards good enough?

It is actually not necessary to use your hardware MAC address. In my case I use a legit SN and MAC of a real 918+ and works just fine.

Well 393 hours, first array is complete, now the 2nd and last one is processing, estimated 15-17 days probably before its completed.

When I was still SHR-1, i had 3x 8TB and 4x 4TB, 1 volume just over 29TB I added a new 8TB to start the processed to SHR-2, once completed will be adding another 4TB and 8TB. I've added plenty of data to my volume, maybe +500GB since I started the process of changing to SHR-2, my question was, what happens to the new data added to the volume while a migration is happening? Is the new data being written to the volume including double parity? Forgot to mention, heck ya when I add huge batches of data, it kills the speed of the resync, just checked, downloading a bunch of movies at 30-40MB\s and my resync is down in the 500kbps range, usually if traffic is light its in the high 2000 to low 3000kbps

I will ask this, maybe some knows.. so there is X amount of data which had 1 parity, now changing to having 2 parity.. that's all great as its reading all the files and figuring stuff about, but due to the nature of how long this takes, I'm constantly adding more and more data in the GB to TB range while this is processing.. is that data written as double parity as I'm adding these new files? or is it caching somewhere to be processed once shr2 migration is completed?

224h, 30.6%

I guess I’m the first risk taker, 152hours, dsm reporting 21.5%, Mdstat shows 43% on first array of 2.