Jump to content
XPEnology Community

vanst

Member
  • Posts

    36
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

vanst's Achievements

Junior Member

Junior Member (2/7)

0

Reputation

  1. Oops, I keep thinking that LACP allow us to bond network card to have a higher bandwidth, like 1 Gpbs + 1 Gbps => 2 Gbps. I will do more learning about this I think you are referring to TL-SG108 - an unmanaged switch. TL-SG108"E" is the Pro version with some L2 features like VLAN and LAG.
  2. Hi All, I set up up a Static LAG with TL-SG108E. NIC teaming has been enabled on the conputer and when downloading / upload something, I can see that packets are distributed between 2 NIC. The same set up had been applied for the NAS, I choose "Balance XOR" since the switch is not supporting dynamic LAG. However, when download / upload a file to the NAS via HTTP / FIle Explore, traffic only flows on one network card. ash-4.3# ifconfig bond0 Link encap:Ethernet HWaddr 10:90:28:EA:80:A8 inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:720074 errors:0 dropped:0 overruns:0 frame:0 TX packets:3259540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:782275593 (746.0 MiB) TX bytes:4559670542 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 10:90:28:EA:80:A8 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:212119 errors:0 dropped:0 overruns:0 frame:0 TX packets:403 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21191560 (20.2 MiB) TX bytes:39678 (38.7 KiB) Interrupt:19 memory 0xd0680000-d06a0000 eth1 Link encap:Ethernet HWaddr 10:90:28:EA:80:A8 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:507955 errors:0 dropped:0 overruns:0 frame:0 TX packets:3259137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:761084033 (725.8 MiB) TX bytes:4559630864 (4.2 GiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1128 errors:0 dropped:0 overruns:0 frame:0 TX packets:1128 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:152400 (148.8 KiB) TX bytes:152400 (148.8 KiB) I am currently running: ############# Update I have tried to setup interface bonding with Mikrotik hAP AC2. Bonding mode is 802.3ad. The same setting in DSM However, still same issue persist. Traffic only goes through 1 network card. Could you advise when possible way to troubleshoot. Thank you!
  3. Hi, Have you try with only 1 network card? What is the result when you try to telet to the DSM portal on port 80 / 443?
  4. Did you set the correct baud rate according to your PC specs? I am not sure but I think that you need a TTL to RS232 converter. This is what I am using at the momment - In the attachment is TTL to RS232 serial converter.
  5. Hi, May I know what CPU you are using? Did you check that the CPU and your loader is compatible, please refer the below post. Also, I would suggest to give a try with 1.03b DS3615xs and see the result.
  6. Can you go to your router - DHCP list and see if the MAC & IP of your NAS is show up there? If you find it, you can access to DSM via IP:5000
  7. Hi all, I found the serial port cable and some logs. Could you assist to check my thread and advise:
  8. Hi, below is the output from serial port: When power on: GNU GRUB version 2.02~beta2-36ubuntu3.14 +----------------------------------------------------------------------------+ |*DS3615xs 6.2 Baremetal with Jun's Mod v1.03b | | DS3615xs 6.2 Baremetal with Jun's Mod v1.03b Reinstall | | DS3615xs 6.2 VMWare/ESXI with Jun's Mod v1.03b | | | | | | | | | | | | | | | | | | | +----------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS, `e' to edit the commands before booting or `c' for a command-line. The highlighted entry will be executed automatically in 0s. patching file etc/rc patching file etc/synoinfo.conf patching file linuxrc.syno patching file usr/sbin/init.post START /linuxrc.syno Insert basic USB modules... :: Loading module usb-common ... [ OK ] :: Loading module usbcore ... [ OK ] :: Loading module ehci-hcd ... [ OK ] :: Loading module ehci-pci ... [ OK ] :: Loading module ohci-hcd ... [ OK ] :: Loading module uhci-hcd ... [ OK ] :: Loading module xhci-hcd ... [ OK ] :: Loading module usb-storage ... [ OK ] :: Loading module BusLogic ... [ OK ] :: Loading module vmw_pvscsi ... [ OK ] :: Loading module megaraid_mm ... [ OK ] :: Loading module megaraid_mbox ... [ OK ] :: Loading module megaraid ... [ OK ] :: Loading module scsi_transport_spi ... [ OK ] :: Loading module mptbase ... [ OK ] :: Loading module mptscsih ... [ OK ] :: Loading module mptspi ... [ OK ] :: Loading module mptsas ... [ OK ] :: Loading module mptctl ... [ OK ] :: Loading module megaraid_sas ... [ OK ] :: Loading module mpt2sas ... [ OK ] :: Loading module mpt3sas ... [ OK ] Insert net driver(Mindspeed only)... Starting /usr/syno/bin/synocfgen... /usr/syno/bin/synocfgen returns 0 All disk ready or timeout execeed [ 5.266089] md: invalid raid superblock magic on sdb3 [ 5.316163] md: invalid raid superblock magic on sdc3 [ 5.373097] md: invalid raid superblock magic on sdd3 [ 5.412305] md: invalid raid superblock magic on sdf3 Partition Version=8 /sbin/e2fsck exists, checking /dev/md0... /sbin/e2fsck -pvf returns 0 Mounting /dev/md0 /tmpRoot ------------upgrade Begin upgrade procedure No upgrade file exists End upgrade procedure ============upgrade Wait 2 seconds for synology manufactory device Fri Apr 10 04:07:59 UTC 2020 /dev/md0 /tmpRoot ext4 rw,relatime,journal_checksum,data=ordered 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 sys /sys sysfs rw,relatime 0 0 none /dev devtmpfs rw,relatime,size=1787092k,nr_inodes=446773,mode=755 0 0 proc /proc proc rw,relatime 0 0 linuxrc.syno executed successfully. Post init [ 19.291545] md1: Failed to send sync event: (sync type: resync, finish: 0, interrupt: 0) ds3615 login: When power off (from DSM interface) ds3615 login: [ 399.080800] Power down. Shortly after that, the system restart itself (it power off & power on). I have tried to shutdown via "poweroff" command but the same thing happen. I have try installed Centos 7 and see that the PC can be shutdown properly.
  9. Hmm, I am using the HP Proliant ML110 serie and it has a serial port ...
  10. Hello, I have a question - If you revert all the changes to the momment your NAS was working (before you installed the PCI card), what happen? You can see more log if you connect to the computer via console (the serial port).
  11. Hello folks, I am still waiting for your advice, could you help me out! Thanks
  12. vanst

    Help

    So you want to clean your WD element disk? ALL THE DATA WILL BE LOST IF YOU WANT TO PROCEED Use Windows+R to open Run, type diskmgmt.msc in the empty box and tap OK. Now identify your WD disk, right click and select format. If you not sure, you can share the screenshot of Disk Management here.
  13. Can you try go to the certificate setting and renew it?
  14. I am really get what you mean. Do you mean that you are not receiving the expected IP per NIC MAC? The most simple way is let the NIC working in DHCP mode, and you can assign the expected IP in your router.
×
×
  • Create New...