blamaster

Hi, can someone help me with the m shell ? I was previously using the pocopicos tcrp (TCRP JOT mode) Now i wanted to use m-shell to build a new loader to perform an dsm upgrade. So far i managed to install the m shell with the following command (from tinycore ssh session) curl -L "https://github.com/PeterSuh-Q3/tinycore-redpill/raw/main/my.sh.gz" --output my.sh.gz tar -zxvf my.sh.gz; After running the ./menu.sh script for the first time it updated tinycore to v14 and rebooted two times. Now if i try to open the m-shell (./menu.sh) again the following log messages appear but the mshell is not loading. Any idea why the mshell wont start ?

Hi, i already posted the question RedPill - the new loader for 6.2.4 - Discussion but i think it was not the matching topic for my question (topic is growing too fast for detailed discussion). I used tinycore to install DS3622xs+ with DSM 7.1-42661 Update 1 on my N54L hardware. On my prvious DSM 6 install i succesfully used zigbee usb dongles with homeassistant. I tried two different dongles with different driver chips (FTDI and CP210x) on the new DSM 7.1 install. For the FTDI based dongle the drivers are already included in the stock kernel so i just loaded them as previously done with DSM6: sudo insmod /lib/modules/usbserial.ko sudo insmod /lib/modules/ftdi_sio.ko Unfortunately both tested usb dongles are not detected by the system. The "dmesg" command shows no log output if the dongles are plugged in. (Not a single line related to the USB dongle, seems like no events are created) If i plug a USB drive in the same USB port the drive i loaded and available in DSM so the USB hub and port seem to work fine in general. Here is the output of "dmesg | grep usb" after the usb dongle was replugged several times: [ 2.265247] <redpill/usb_boot_shim.c:229> Registering USB boot device shim [ 2.265487] <redpill/usb_boot_shim.c:194> Registered usbcore module notifier [ 2.269655] <redpill/usb_boot_shim.c:247> Successfully registered USB boot device shim [ 13.933321] usbcore: registered new interface driver usbfs [ 13.933528] usbcore: registered new interface driver hub [ 13.933736] usbcore: registered new interface driver ethub [ 13.933943] usbcore: registered new device driver usb [ 13.934137] <redpill/usb_boot_shim.c:166> usbcore registered, adding device watcher [ 13.934405] <redpill/call_protected.c:112> Got ptr ffffffffa00d7db0 for usb_register_notify [ 13.934698] <redpill/usb_boot_shim.c:127> Registered USB device notifier [ 13.972036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.979871] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.988036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 14.044782] usbcore: registered new interface driver usb-storage [ 14.302061] usb 2-3: new high-speed USB device number 2 using ehci-pci [ 14.440089] usb-storage 2-3:1.0: USB Mass Storage device detected [ 14.442075] scsi host6: usb-storage 2-3:1.0 [ 14.442352] <redpill/usb_boot_shim.c:91> Device <vid=xxxx, pid=xxxx> shimmed to <vid=xxxx, pid=xxxx> [ 16.494373] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa018a470> [ 25.413853] systemd[1]: Starting Mount usb fs... [ 25.914175] usbcore: registered new interface driver usblp [ 25.931881] usbcore: registered new interface driver usbhid [ 25.932107] usbhid: USB HID core driver [ 25.973474] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa0b59470> [ 48.955098] usbcore: registered new interface driver usbserial [ 48.998396] usbcore: registered new interface driver ftdi_sio [ 48.998620] usbserial: USB Serial support registered for FTDI USB Serial Device The "lsusb" command also only shows connected USB drives. The zigbee dongles dont show up in the lsusb output: |__usb1 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:12.2) hub |__usb2 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:13.2) hub |__2-3 f400:f400:0200 00 2.00 480MBit/s 100mA 1IF (USB Disk 2.0 HEADER1397438310856) |__usb3 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:16.2) hub @flyride mentioned it could be related to the discontinued USB support by synology: https://macandegg.com/2021/06/synology-dsm-7-0-ends-support-for-usb-devices/#:~:text=DSM 7.0%3A No more USB sticks&text=First%2C the support for external,LTE sticks%2C Bluetooth dongles anymore. I still have the feeling the issue is somewhere else. I would guess synology just removed additional usb drivers and hide devices except for Usb drives from the UI but i can not really imagine they put so much effort into kernel / driver modification to fully prevent the system from detecting other USB devices. Also there are manuals like: https://mariushosting.com/synology-how-to-add-usb-support-on-dsm-7/ which describes how to load the missing driver modules (same as i did above) to enable the USB support on DSM7 (and a lot of users responded it worked). Can maybe someone with Tinycore and DS3622xs + DSM 7.1 test if USB devices are alow not showing in the syslog (except for USB ones) ? Instead of Zigbee or Zwave dongles i also tried to attach a keyboard to the N54L, it is also not detected according to the syslog.

I used tinycore to install DS3622xs+ with DSM 7.1-42661 Update 1 on my N54L hardware. The install process worked without issues 🙂 On my prvious DSM 6 install i succesfully used zigbee usb dongles with homeassistant. I tried two different dongles with different driver chips (FTDI and CP210x) on the new DSM 7.1 install. For the FTDI based dongle the drivers are already included in the stock kernel so i just loaded them as previously done with DSM6: sudo insmod /lib/modules/usbserial.ko sudo insmod /lib/modules/ftdi_sio.ko Unfortunately both tested usb dongles are not detected by the system. The "dmesg" command shows no log output if the dongles are plugged in. (Not a single line related to the USB dongle, seems like no events are created) If i plug a USB drive in the same USB port the drive i loaded and available in DSM so the USB hub and port seem to work fine in general. Here is the output of "dmesg | grep usb" after the usb dongle was replugged several times: [ 2.265247] <redpill/usb_boot_shim.c:229> Registering USB boot device shim [ 2.265487] <redpill/usb_boot_shim.c:194> Registered usbcore module notifier [ 2.269655] <redpill/usb_boot_shim.c:247> Successfully registered USB boot device shim [ 13.933321] usbcore: registered new interface driver usbfs [ 13.933528] usbcore: registered new interface driver hub [ 13.933736] usbcore: registered new interface driver ethub [ 13.933943] usbcore: registered new device driver usb [ 13.934137] <redpill/usb_boot_shim.c:166> usbcore registered, adding device watcher [ 13.934405] <redpill/call_protected.c:112> Got ptr ffffffffa00d7db0 for usb_register_notify [ 13.934698] <redpill/usb_boot_shim.c:127> Registered USB device notifier [ 13.972036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.979871] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.988036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 14.044782] usbcore: registered new interface driver usb-storage [ 14.302061] usb 2-3: new high-speed USB device number 2 using ehci-pci [ 14.440089] usb-storage 2-3:1.0: USB Mass Storage device detected [ 14.442075] scsi host6: usb-storage 2-3:1.0 [ 14.442352] <redpill/usb_boot_shim.c:91> Device <vid=xxxx, pid=xxxx> shimmed to <vid=xxxx, pid=xxxx> [ 16.494373] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa018a470> [ 25.413853] systemd[1]: Starting Mount usb fs... [ 25.914175] usbcore: registered new interface driver usblp [ 25.931881] usbcore: registered new interface driver usbhid [ 25.932107] usbhid: USB HID core driver [ 25.973474] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa0b59470> [ 48.955098] usbcore: registered new interface driver usbserial [ 48.998396] usbcore: registered new interface driver ftdi_sio [ 48.998620] usbserial: USB Serial support registered for FTDI USB Serial Device The "lsusb" command also only shows connected USB drives. The zigbee dongles dont show up in the lsusb output: |__usb1 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:12.2) hub |__usb2 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:13.2) hub |__2-3 f400:f400:0200 00 2.00 480MBit/s 100mA 1IF (USB Disk 2.0 HEADER1397438310856) |__usb3 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:16.2) hub Is this related to the redpill loader ?

I used tinycore to install DS3622xs+ with DSM 7.1-42661 Update 1 on my N54L hardware. The install process worked without issues 🙂 On my prvious DSM 6 install i succesfully used zigbee usb dongles with homeassistant. I tried two different dongles with different driver chips (FTDI and CP210x) on the new DSM 7.1 install. For the FTDI based dongle the drivers are already included in the stock kernel so i just loaded them as previously done with DSM6: sudo insmod /lib/modules/usbserial.ko sudo insmod /lib/modules/ftdi_sio.ko Unfortunately both tested usb dongles are not detected by the system. The "dmesg" command shows no log output if the dongles are plugged in. (Not a single line related to the USB dongle, seems like no events are created) If i plug a USB drive in the same USB port the drive i loaded and available in DSM so the USB hub and port seem to work fine in general. Here is the output of "dmesg | grep usb" after the usb dongle was replugged several times: [ 2.265247] <redpill/usb_boot_shim.c:229> Registering USB boot device shim [ 2.265487] <redpill/usb_boot_shim.c:194> Registered usbcore module notifier [ 2.269655] <redpill/usb_boot_shim.c:247> Successfully registered USB boot device shim [ 13.933321] usbcore: registered new interface driver usbfs [ 13.933528] usbcore: registered new interface driver hub [ 13.933736] usbcore: registered new interface driver ethub [ 13.933943] usbcore: registered new device driver usb [ 13.934137] <redpill/usb_boot_shim.c:166> usbcore registered, adding device watcher [ 13.934405] <redpill/call_protected.c:112> Got ptr ffffffffa00d7db0 for usb_register_notify [ 13.934698] <redpill/usb_boot_shim.c:127> Registered USB device notifier [ 13.972036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.979871] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 13.988036] <redpill/usb_boot_shim.c:75> Found new device <vid=xxxx, pid=xxxx> - didn't match expected <vid=xxxx, pid=xxxx> (prev_shimmed=0) [ 14.044782] usbcore: registered new interface driver usb-storage [ 14.302061] usb 2-3: new high-speed USB device number 2 using ehci-pci [ 14.440089] usb-storage 2-3:1.0: USB Mass Storage device detected [ 14.442075] scsi host6: usb-storage 2-3:1.0 [ 14.442352] <redpill/usb_boot_shim.c:91> Device <vid=xxxx, pid=xxxx> shimmed to <vid=xxxx, pid=xxxx> [ 16.494373] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa018a470> [ 25.413853] systemd[1]: Starting Mount usb fs... [ 25.914175] usbcore: registered new interface driver usblp [ 25.931881] usbcore: registered new interface driver usbhid [ 25.932107] usbhid: USB HID core driver [ 25.973474] <redpill/bios_shim.c:215> Symbol #59 in mfgBIOS "broadwellnk_synobios" {syno_usb_prohibit_event}<ffffffffa0b59470> [ 48.955098] usbcore: registered new interface driver usbserial [ 48.998396] usbcore: registered new interface driver ftdi_sio [ 48.998620] usbserial: USB Serial support registered for FTDI USB Serial Device The "lsusb" command also only shows connected USB drives. The zigbee dongles dont show up in the lsusb output: |__usb1 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:12.2) hub |__usb2 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:13.2) hub |__2-3 f400:f400:0200 00 2.00 480MBit/s 100mA 1IF (USB Disk 2.0 HEADER1397438310856) |__usb3 1d6b:0002:0404 09 2.00 480MBit/s 0mA 1IF (ehci_hcd 0000:00:16.2) hub Is this related to the redpill loader ?