Jump to content
XPEnology Community

specter9mm

Rookie
  • Posts

    9
  • Joined

  • Last visited

Everything posted by specter9mm

  1. @IG-88finally got this working. I updated to DSM7 with the redpill loader and had the exact same issue. Swapped the card out for another one I had here, and it worked perfectly, interfaces detected on boot and available in the DSM interface. I didn't happen to grab the model of the card that wouldn't detect on boot, but the one that works is a Solarflare Communications SFC9020 10G Ethernet Controller.
  2. I have a question about quicksync compatibility. My current build is a 9900k which I utilize for hardware HEVC trans-coding. DS918+ would be the most appropriate, but would limit me to 8 threads, while the CPU is capable of 16. I have no idea what type of work it would take to get quicksync compatibility on the DS3622xs+ image. Is this something that is possible post install with that option?
  3. New extras did not cause the sfp+ interfaces load on boot. I stuck with 1.04b and 918+ as I have a bunch of folks using the box, and can't have a ton of extended downtime while I try it on 1.03b and 3617xs, only to migrate back.
  4. A little change since last year. Jun's Loader v1.04b with DS918+ DSM 6.2.3-25426 Update 3 (Release notes) Using the extra and extra2.lzma, but which versions I have no idea. Did this a while ago, and just made sure everything I got to work together was zipped and backed up. This is the 2 port sfp+ card I put in, SFN5122F Solarflare S6102 10G Ethernet Dual Port Server Adapter PCI Express, I have tried multiple different GBICS. It looks like you may have updated extra lzmas for both my issues actually, as with this recent redo I still had to manually copy i915.ko into place to get HEVC hw offloading to work. I think I went to 1.04b in the first place because I couldn't get the i915.ko to work on 1.03b with the 3617+ install. First will try replacing both extras on the boot stick. Will report back once I get a chance to do that.
  5. So this also happens on a fresh install, as I just replaced all my drives in my build, and did a completely fresh install with the SFP+ card in during the install. Still looking for where the DSM config can be edited to permanently add bringing up these interfaces on boot.
  6. Hey folks, sorry if this is covered somewhere else, I could not find anything. I added a two port sfp+ card with a 10GB fiber module to my already running xpenology bare metal. Everything works, except I can't get the darn interface to come up on boot. If I go to Control Panel->Network in DSM, it only shows my original interfaces. If I ssh to the box, and do "ifconfig ethx up", the interface comes up, get link and dhcp, and appears in DSM. I have added ifcfg-ethx for the two interfaces to /etc.defaults/sysconfig/network-scripts. How do I get these to come up automatically?
  7. Outcome of the installation/update: FAILED - DSM version prior update: DSM 6.2.3-25426 Update 3 - Loader version and model: Jun's Loader v1.03b - DS3617xs - Using custom extra.lzma: YES - Installation type: ASRock Z390M-ITX/ac - VENGEANCE® LPX 16GB (2 x 8GB) DDR4 DRAM 3000MHz C15 Memory Kit - Intel 9900K - Additional comments: Update applied to running system. - Notes: System hangs initializing, appears to be during driver/kernel module load.
  8. That is disappointing. The new nas is performing so well I am saturating the 1Gb link.
  9. Second network port is not coming up. Wondering if the drivers need to be updated. I chose to go with the 1.0.3b bootloader with 3617. Motherboard - Z390M-ITXac Ethernet - - 1 x Giga PHY Intel® I219V, 1 x GigaLAN Intel® I211AT Really odd, but I see one of the required drivers listed in lsmod, but it says it's not used by any devices. Checked the intel website, and the I219 is the "em" driver, and the 211 is "igb". igb is present, but listed with 0 devices. "ash-4.3# lsmod | grep igb igb 175161 0" em is not present at all. e1000e which is listed as the supporting driver also shows 0 devices. ash-4.3# lsmod | grep e1000 e1000 99771 0 e1000e 169025 0 I believe I have all the grub settings correct. As far as I can tell the hardware is definitely not showing up at all in the OS. ash-4.3# grep -r '.*' /sys/class/net/*/device/vendor 0x8086 ash-4.3# grep -r '.*' /sys/class/net/*/device/irq 17 ash-4.3# grub.conf set mac1=macfromswitch set mac2=macfromswitch set rootdev=/dev/md0 set netif_num=2 I started a pxe boot on each port and recorded the mac address from the switch. mac1 is working just fine.
×
×
  • Create New...