• Content Count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About Alex_G

  • Rank

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. UPDATE! If i create Datastore on VMWARE and add this datastore to Xpenology, my Volumes are not lost after restart. If i make RAW mount and creat VMFS images and than i add those existing disks to Xpenology VM than i always lose volume/raid group at each restart. Any idea what i'm doing wrong? Maybe now someone will have idea where i'm wrong. Thank you, Alex_G
  2. Thank you per4manc! I actualy just did clean install and nothing else. Can you tell me which instalation procedure and versions did you use. my problem in details you can see in this topic: Thank you, Alex_G Th
  3. Dear all, I was installing mine Xpenology with manuals and files from pigr8 All went fine, until 1st reboot. Afer reboot i lost RAID group and Volume. When Xpenology boot without RAID group and Volume, i can easybuild RAID group again and create Volume and it will work again untill 1st reboot (normaly if there were any data, all is lost). The RAID group and Volume creatad on VMware virtual disk won't diapear after restart: Hard disk 1: 8GB Thin provisioned SCSI controller 0, SCSI (0:0) Dependent Hard disk 3: 3TB Thick provisioned, lazly zeroed SCSI controller 0, SCSI (0:1) Independent - persistant Hard disk 4: 3TB Thick provisioned, lazly zeroed SCSI controller 0, SCSI (0:2) Independent - persistant System: HP N54L, 16GB RAM, 250GB HDD + 2x 3TB HDD in RAW mode mounted in RDM loader: 1.02b DS3615xs, DSM 6.1.4-15217 Update1 Hope nayone will have idea how to solve that, as i was searching forum and wasn't able to find solution how to solve. Thank you! Alex_G
  4. I must agree with you. Like you said, i'm on loader 1.02b DSM 6.1.4-15217 and i'll open new treath. I used files from pigr8. Thank you! Alex_G .
  5. Anyone. I have totaly same problem, RAID group and volume lost after restart. Thank you!
  6. Just followed this guide and worked perfectly,... untill first restart. Can someone help me what i've done wrong. After restart Volume is gone. I did manualy instal DSM 6.1.4 Update 1 But othervise first manuals that startup at first shoot! Thank you so far pigr8!!!
  7. Hello cri5py, I had sam problem yesterday with one of mine testing NAS (virtual on ESXi 6.5) i got same problem. And i couldn't resolve. I did try several restar, but i didnt' restart Host because i was not able because of otehr running VMs. I'll try again with full restar. Thnks to your post and I'll report results. Thank you, AG
  8. Update: System is running on: - HP Microserver 2 CPUs x AMD Turion(tm) II Neo N54L Dual-Core Processor - 16 GB RAM - Inside is 250 GB HDD for System (ESXi 6.5) and there is also stored all virtual machines (Xpenology) - 2x 3 TB WD HDD added in RAW mode (used for SHR RAID on Xpenology) Like i wrote i having problems with disks after restar or even start if i add more than 1 raw disk to Xpenology. Problem: - no disk after restart - volume crash - if both 2,7 TB HDDs added before star virtual machine, machine won't get IP and i can't find it on network (find. This is my second test/backup NAS, so i can rebuild it from scratch, but i really can't find one really working solution. Please if someon running same hardware with NAS on ESXi, can you help me how exactly you build loader (i think i should use 1.02b by June) and as i read on forum i can manualy update DSM to 6.1.3. If soemone can help me to build working DSM 6.1.3 on ESXi i will be very greatfull (yes, i did read forum up and down, but no final success). Thank you, Alex_G
  9. I have strange problem with Xpenology. I try alot of combination last few days. 1st when build Xpeno 6.1.3 or 6.0.2 both turn on and i can setup DSM after i add 1st 3TB hdd (in raw mode),.. images is located in RDM folder Xpenology still boot OK and i can create volumes, shutdown, restart anything,... 2nd when build Xpeno 6.1.3 or 6.0.2 both turn on and i can setup DSM after i add 2nd 3TB hdd (in raw mode),.. images is located in RDM folder Xpenology wont boot to working state. Xpenology start, but network is not up and i can't find it on network at all. So to make it simple, if i add more than i 3TB hdd to Xpenology it won't start to working stat anymore situation: HDD1 = botloader HDD2 = system disk HDD3 = 1st 3TB data disk HDD4 = 2nd 3TB data disk Does anybody have a clue what could resolve this? Alex_G
  10. Can we use any other PAT file or must be DSM_DS3612xs_4482.pat? Possible to use DSM from other hardware, like DS412+ (DSM_DS412+_4482.pat) or DS413 (DSM_DS413_4482.pat) ? Thank you, Alex_G
  11. Hello, I did install ESXi and gnoboot (10.3) and prepare ESXi to boot gnoboot. When i start Synology Assistant it found DiskStation with Status "Not installed". When i select DiskStation and press Connect, Assistant open default web browser (i did try Mozilla, IE11, Chrome) and in corner left show "Web Assistant" and in right "Synology", but afted some time i get timeout message "Connection failed. Please check your network settings." Does anyone have idea what is wrong? I did already instal 4.3 and also 5.0 up to update2, but today no way to load DSM on DiskStation.
  12. Ok, sucessfuly installed, using gnoboot-alpha10.3-custom-ESXi-vfat. All went smooth. But what now. I try to copy files to DSM and from. Also all work well. But what i have to do wehn i restart virtual machine, to get normal boot directly into DSM? Also how to update from 10.3 to 10.5 if this si important? Thank you all and sorry for stupid question. Regards, Alex_G