Jump to content
XPEnology Community

chemistry

Member
  • Posts

    27
  • Joined

  • Last visited

Posts posted by chemistry

  1. - Outcome of the update: SUCCESSFUL

    - DSM version prior to update: DSM 6.2.1-23824U6

    - Loader version and model: Jun v1.04b - DS918

    - Using custom extra.lzma: YES

    - Installation type: BAREMETAL - ASRock J5005-ITX

    - Additional comments: i used the real3x mod - big THANKs to you!

    • Like 2
  2. On 4/18/2019 at 12:23 AM, flo3393 said:

    Hello,

     

    is a new loader for 918+ coming to Support 6.2.2 ? Some People have Network Problems with onboard CPUs like J5005. 

     

    Thanks!

     

    Would be also interessted... ':)

    • Like 1
  3. Outcome of the update: FAILED

    DSM version prior to update: DSM 6.2.1-23824U6

    Loader version and model: Jun v1.04b - DS918

    Using custom extra.lzma: NO

    Installation type:  BAREMETAL -  Asrock J5005-ITX @BIOS 1.40, 16GB RAM

    Additional comments: No network after Reboot.

  4. Uh - i think i managed to step down successfully!

    Your hint with using a newly created USB Bootloader stick did the trick.

    DSM seems to write some kind of version infos to the USB device. That blocked the installation of the older version.

     

    Before i wiped all 2.4GB partitions on the harddrives with zeros with MiniTool Partition Wizard.

     

    But thank you ALL for your help 🤗

     

     

  5. A new install is not working with my Asrock J5005-itx and the Loader 1.04b

     

    After Reboot the network Interface stops working and i can obtain no IP Adress.

     

    Worst thing is i can't step back to the older version. The Web Assistant tells me i need to use a Installer file wiith version 6.2.2-24922 or later....

     

    Any ideas?

     

  6. On 2/17/2019 at 5:14 PM, JMRR said:

    Folowed your tuturial, instaled on askock J5005-itx with 4gb ram(i need more i know), valid sn+mac from one rs model.
    Migrate dsm from esxi(hdd raid 1 configuration in rdm mode), everithing went smooth.
    /dev/dri is in place, and codecs is activated.
    This combo is an amazing setup for dsm.

    The only thing doesent work is reboot or shutdow.

    I use bios 1.0 i think, its beter to upgrade or doesent mater?



    Sent from my iPad using Tapatalk

     

    For me shutdown and reboots work fine.

    Only Drives don't spin down for energy saving...

  7. Outcome of the installation/update: SUCCESSFUL

    - DSM version prior update: DSM_DS918+_23824

    - Loader version and model: JUN'S LOADER v1.04b

    - Using custom extra.lzma: NO

    - Installation type: BAREMETAL  ASRock J5005-ITX

    - Additional comments: Internal NIC works great / REBOOT, OK and Shutdown OK

  8. Hi all!

     

    I am pretty new to this thing - but it's awesome.

    A question i got is regarding Quickconnect.

    It is recommended not to use a serial for the box out of the generator for Quick Connect.

     

    My question is - can i use a original serial from a older box and model (from a 216) for the 918+ Model and then use Qucik Connect?

    Are the serials not connected to a special model type? 

    For my install i used a key from the generator - but for the 916+ Model - but it worked for the 918+ too.....

     

    Would be awesome if this works.

     

    Thanks!

  9. Outcome of the installation/update: SUCCESSFUL

    - DSM version prior update: DSM_DS918+_23824

    - Loader version and model: JUN'S LOADER v1.04b

    - Using custom extra.lzma: NO

    - Installation type: BAREMETAL  ASRock J5005-ITX

    - Additional comments: Internal NIC works great

    - Additional comments: REBOOT, OK and Shutdown OK

     

  10. Ok - thank you for your answer...

     

    I think i will go for new hardware. I read some reviews and even the SOC Board J5005 ist significantly (+50%) faster then my old PC hardware.

    And i really want to have new DSM Versions supported. 

     

    Any suggestions what might be the best shot for hardware? Is it a SOC like the Asrock J5005 or is a generic new Intel CPU + Mainboard better (in terms of compatibility now and in future?)

  11. Hi Guys!

     

    As my old NAS died some days ago, i stumbled over this solution to build a new NAS wie XPEnology.

     

    I got the situation here, that i have old Hardware in use that currently is used as a fileserver and downloadstation. It runs under Windows10 with a drive pool Software called Drivebender.

     

    It works pretty well (now for years), but there are no benefits regarding Backups, Raid etc.

     

    Now i am asking me, how to start.... using the old Hardware and just install XPEnology and be happy or buy new stuff thats (maybe) faster and more efficent?

     

    I am currently using 

    CPU:  Intel Pentium G840 (Sandy Bridge) 2Core (Max TPD65W)

    Mainboard: MSI H67MA-E35

    RAM: 4GB DDR3 (2x2GB)

     

     

    Would new Hardware like a Asrock j3455 + RAM be more efficient and faster?

    Is the old hardware in theory capable of beeing used?

    Or would be the best to go for new CPU and Board and RAM like  8th gen i3/i5 + Asrock H370M-ITX ?

     

    Thanks for your help,

     

    chemistry

     

     

     

×
×
  • Create New...