Jump to content
XPEnology Community

AndreyATGB

Member
  • Posts

    42
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by AndreyATGB

  1. AndreyATGB

    DSM 6.2 Loader

    If you can SSH or telnet then you can run synouser --setpw [USERNAME] [NEWPASS] If not, then you can choose the reinstall option in the bootloader to reset DSM while keeping data. There might be a way of doing it by mounting the system partitions but I don’t know what you need to modify after doing that.
  2. - Outcome of the update: SUCESSFUL - DSM version prior update: DSM 6.2.1-23824 Update 6 - Loader version and model: JUN'S LOADER v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - Asrock Z390M-ITX, i5 9600k, I211/219V NICs - Additional comment: Updated without issues, 219V NIC still doesn’t work.
  3. I have a 9600K on a Z390 board and it also doesn't show up (i5 7400 did). The driver is too old, from what I gather there is not much we can do about it. The kernel has to be updated most likely. The iGPU is detected in lspci, i915 is loaded but unused.
  4. - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.1-23824 Update 4 - Loader version and model: Jun's Loader v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - H110M-ITX, i5 7400, onboard Intel NIC - Additional comments: Reboot required
  5. AndreyATGB

    DSM 6.2 Loader

    Did you try DSM 6.2 with DS3615? 6.2.1 doesn’t work with 3617 at all and also doesn’t seem to work with non-Intel NICs, so it probably won’t work for you since you have Realtek.
  6. AndreyATGB

    DSM 6.2 Loader

    There’s your problem. DS918+ is Haswell or newer, you can’t use it with your CPU.
  7. AndreyATGB

    DSM 6.2 Loader

    Most likely 3615/17 with 1.02b DSM 6.1.x. Are you sure you've installed DSM 6.2 and not 6.2.1? It might work as well but I'm fairly sure 6.1 will work.
  8. Late reply but this is probably not going to work. I tried a couple valid pairs from different models and it seems you need a pair from the same box at the very least. A pair from a different model will give an error when you try to use quickconnect. Worth noting that you only need a valid serial for video station hardware acceleration, not sure about other packages.
  9. - Outcome of the update: SUCCESSFUL - DSM version prior update: DSM 6.2.1-23824 Update 1 - Loader version and model: Jun's Loader v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - H110M ITX, i5 7400, Intel I219V NIC - Additional comments: Everything seems OK.
  10. AndreyATGB

    DSM 6.2 Loader

    I’d guess there will be an update for DS3615/17, it’s the most stable version after all. You’re not really missing anything, in fact 1.03b can work with DSM 6.2.1, at least if you have an Intel NIC it should. On my hardware it works just fine for example.
  11. AndreyATGB

    DSM 6.2 Loader

    All I find for that model are Core 2 models, the CPU is way too old if that’s the case. DS918+ only works on Haswell and newer.
  12. AndreyATGB

    DSM 6.2 Loader

    CPU appears to be Ivy Bridge, DS918+ loader only works on Haswell and newer.
  13. AndreyATGB

    DSM 6.2 Loader

    It should, but try it in a new VM just to be sure. 1.03b might also work (3615/17) depending on your hardware, it worked for me on baremetal Kaby Lake with Intel NIC but didn’t in a VM.
  14. AndreyATGB

    DSM 6.2 Loader

    It won’t work on Ivy Bridge, you need Haswell or newer for DS918+.
  15. - Outcome of the installation/update: SUCCESSFUL - DSM version prior update: 6.2-23739 Update 2 - Loader version and model: Jun v1.04b - DS918+ - Using custom extra.lzma: NO - Installation type: BAREMETAL - H110M ITX, i5 7400, Intel I219V NIC - Additional comments: Boot 6.2U2 with 1.04b, install 6.2.1, install 6.2.1u1.
  16. AndreyATGB

    DSM 6.2 Loader

    It’s probably mislabeled since it says DS918+. I still have the img as well but I’m pretty sure that’s the same one.
  17. AndreyATGB

    DSM 6.2 Loader

    It does actually work. It depends on your hardware. It seems Realtek NICs don’t work for example.
  18. AndreyATGB

    DSM 6.2 Loader

    I don’t remember the brand, I think it’s IOcrest or something. I finally managed to enter its BIOS but there’s nothing to configure besides RAID (which was disabled anyway). It only shows the one sata disk I have installed, it’s marked as AHCI Mode. It doesn’t show the empty slots or any way to disable the IDE port. It’s probably some weird interaction with the DS918+ loader considering that it is being detected but for some reason just doesn’t work. With the DS3615 loader the disk showed exactly as it would if I had it plugged in directly the motherboard. I’ll just switch to DS3615 when I actually need to use the extra ports. It could be that the IDE port is the problem with the newer kernel that DS918+ uses, I don’t care enough about hardware acceleration to get another card right now.
  19. - Outcome of the installation/update: SUCCESSFUL - DSM version prior update: Fresh install on 6.2.1 - Loader version and model: JUN'S LOADER v1.03b - DS3615xs - Using custom extra.lzma: NO - Installation type: Baremetal - ASRock H110M ITX (Intel NIC), i5 7400, 8GB RAM - Additional comments: Seems to work fine. Additional SATA ports from 88SE9128 PCIe card also work.
  20. AndreyATGB

    DSM 6.2 Loader

    I can't get the DS918+ loader to detect HDDs on a 88SE9128. It shows up in lspci in slot 1:00: root@NAS:~# lspci -s 1:00 0000:01:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9128 PCIe SATA 6 Gb/s RAID controller (rev 20) 0000:01:00.1 IDE interface: Marvell Technology Group Ltd. 88SE912x IDE Controller (rev 20) 0001:01:00.0 Non-VGA unclassified device: Marvell Technology Group Ltd. Device 9215 (rev ff) It also clearly tries to load it during boot but fails with COMRESET errors repeating for a couple minutes. Relevant grub config: set common_args_918='syno_hdd_powerup_seq=1 HddHotplug=1 syno_hw_version=DS918+ vender_format_version=2 console=ttyS0,115200n8 withefi elevator=elevator quiet syno_hdd_detect=0 syno_port_thaw=1' set sata_args='sata_uid=1 sata_pcislot=1:00 synoboot_satadom=1 DiskIdxMap=0005 SataPortMap=44' The disk is detected with DS3615xs. Custom extra.lzma makes no difference, the driver loads just fine with the stock one. I will investigate further since I did somehow manage to get the installer to detect a fresh disk with 918+ but I'm still trying to replicate it.
  21. Pretty sure you need a DDNS unless you have a static IP address. Personally I use a DDNS and a certificate from Let’s Encrypt. I transfer over secure WebDAV and I only allow HTTPS for the web interface. You can use a VPN to setup the secure connection instead of HTTPS, but you’ll still need to know the server’s IP. By using a VPN you should in theory be able to access it as if you were on the same network (for instance use the 192.168.1.x address).
  22. AndreyATGB

    DSM 6.2 Loader

    Not if you use the ESXi option and boot from a virtual disk. The vid/pid only affect your ability to install AFAIK, if you get error during install you have to make sure they’re correct. Personally I ran it in VMs with both normal and ESXi boot options without touching vid or pid just fine.
  23. AndreyATGB

    DSM 6.2 Loader

    Interesting, anyone tried baremetal? Everyone in the update thread so far has ESXi as well, which makes sense as it’s easy to reverse if it goes wrong.
  24. AndreyATGB

    DSM 6.2 Loader

    918+ (1.03a2) doesn't show up on network in my test VM after applying 6.2.1. I attached serial log from the VM: line 0-54 = normal boot with 6.2u2 line 59-468 = boot right after uploading .pat in DSM line 468+ = another try, same error with mptspi (?) It does not boot with either BIOS or UEFI. Don't take this as proof that the update doesn't work though, the VM only boots (with 6.2) with the baremetal option and only in BIOS mode. My baremetal install boots with UEFI just fine.
×
×
  • Create New...