Ikyo
-
Posts
22 -
Joined
-
Last visited
Posts posted by Ikyo
-
-
Any news about a loader for the older generation CPUs?
-
I am going to guess that you have an older CPU that isn't supported by the DS918 loader.
-
Has it been said if there are any plans to update the other versions?
-
I am only seeing the 918 currently. I am sure Jun will release the others as soon as he is able.
-
I downloaded the version that I found and it works for 6.2. I must have had an older version. Thank you for updating it.
-
DO you have a direct link to the one that I should be using? The one I tried had an error and had to uninstall it.
-
On 11/11/2017 at 1:27 AM, 4sag said:
open-vm-tools 6.1_10.1.15
Are you going to build a version for 6.2?
-
If anyone finds a working version of VMWare Tools let me know. My old version errored out when I upgraded to 6.2
-
Have you found a working version of VMwaretools?
-
8 hours ago, andrey00188 said:
Hуllo everyone!
Tell me, please, how to update me with 6.1 downloader 1.02b to 6.2 downloader 1.03b. Install in ESXi
I tried simply to replace the bootloader, but the machine willn't get ip ((I haven't tried this yet, but I am going to guess you need to update the GRUB configuration to have the correct MAC1 address to match the ESXI configuration.
-
4 hours ago, Bi0 said:
@mrlgm007 how far are you getting?
My VM setting are below. Hope it helps?
What CPU do you have on this? I am sure it is going to make the difference. I tried to setup a machine exactly like that, but wouldn't boot because of the processor.
-
I have actually gotten the NIC to show up on my switch, but it didn't get an IP address. To get it to show up I switched from BIOS to EFI in the VMWare loader. I am wondering if I am seeing the NIC register because of the way it is handled with EFI.
-
1 minute ago, IG-88 said:
please be more specific about what chip the nic is, at least the i217 seems to be a problem
if you cant check about the chip please give the product name of the nic or the system board (if its onboard)
It is using one of the internal Broadcom Gigabit Ethernet BCM5720 NICs and ESXI is emulating an e1000e. I will go back and try the VMXNET3.
-
Unable to discover it and not showing on my network. I have tried both the baremetal and VMware options from the Grub loader.
Processor: Intel(R) Xeon(R) CPU E5-2665 0 @ 2.40GHz
ESXI Version: 6.7
Host Config:
SATA Controller
e1000e Network Card
50mb boot (SATA0)
16gb test drive (SATA1)
I attempted to set the mac address in the GRUB loader with the set command to match the interface. That did not work. I am willing to try different options if people have suggestions.
-
I had some issues with it and went back to ESXI.
-
I do agree that it sucks, but I am glad to know it wasn't me doing something wrong
In your opiniion, could I run the R710 as an iSCSI data store for VMs and be okay with the 1Gb limitation or do I need to look at other options? I am upgrading to a Dell R720, but it uses 2.5" drives. So for me to rebuild the array, it would be pretty costly. I was looking at like Open-E, but I am not sure it will do any better.
-
I have a couple of datashares setup on a bare metal install (Dell R710). I have the H700 raid array controlling the 6 2 TB drives. They are in a RAID 5 configuration. I have 3 nics on both the ESXI server and the Synology box (all Gig-E). I can see it splitting the traffic between the 3 NICS, but the speed doesn't go up. It seems to max out at the same amount 1 NIC would be. Do I have something configured wrong or is this the best I will be able to do?
-
I ended up going to 3615 over 3617. I also used your version 3.2 file.
-
I was able to track down the 3.2 driver package and loaded it. When I try to install Xpenology, I keep getting error 13 no matter what I try. I have tried a couple USB drives and still no luck. It is always saying that it is trying to migrate. I am not sure why it thinks it can migrate when I complete redo the USB. I am thinking it is trying to install on the raid controller possibly or maybe the SATA SSD that I had in the system. Anyone that has a R710 and bare bones working, please let me know.
-
I am attempting to install Xpenology on one of my R710s as a baremetal install. I had it installed on VMWare with no problems, but this is being a little more problematic. Everything appears to boot okay, but I don't believe it has the NIC drivers. I am also seeing that the extra RAM disk is currently removed. I am using Juns 1.02b loader for the 3617xs. What options do I have to get this up and running?
has anyone got dsm 6.2.2 barebone on the dell poweredge r710
in DSM 6.x
Posted
How did you get 6.2.2 to work? The CPU version should be wrong on that server.