• Content Count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About e-ghost

  • Rank
    Junior Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Hi @IG-88, read what you wrote and understood the situation now. Thanks a lot!
  2. Hi, may I ask if v1.04b loader for 918+ with mpt2sas under 6.2.3 still haven't issue with HDD Hibernation? Is there any solution to re-gain the HDD hibernation under this combination? Thanks a lot!
  3. sorry I found out the problem and resolved! I copied /etc.defaults/syslog-ng/patterndb.d/scemd.conf as /etc.defaults/syslog-ng/patterndb.d/scemd.conf_orig as a backup. The system also loaded both scemd.conf and scemd.conf_orig also. After I removed scemd.conf_orig then it works! Sorry for stupid question but you still keep on helping! ^_^
  4. Thanks a lot! I got these: bash-4.3# ls -l /etc.defaults/syslog-ng/patterndb.d/scemd.conf -rw-r--r-- 1 root root 261 Dec 27 01:46 /etc.defaults/syslog-ng/patterndb.d/scemd.conf bash-4.3# cat /etc.defaults/syslog-ng/patterndb.d/scemd.conf filter f_scemd { program(scemd); }; filter f_scemd_sev { level(err..emerg) }; # destination d_scemd { file("/var/log/scemd.log"); }; destination d_scemd { file("/dev/null"); }; log { source(src); filter(f_scemd); filter(f_scemd_sev); destination(d_scemd); }; bash-4.3# ls -l /etc/syslog-ng/patterndb.d/scemd.conf -rw-r--r-- 1 system
  5. Can you help to take a look what I did wrong? I already fully copied your file to replace my /etc.defaults/syslog-ng/patterndb.d/scemd.conf. After rebooted, the /etc/syslog-ng/patterndb.d/scemd.conf is the same as it. However, I see the /var/log/scemd.log is still keep on growing 8-lines per minute: 2020-12-27T02:10:49+08:00 fevernas03 scemd: SYSTEM: Last message 'polling_fan_speed_rp' repeated 1 times, suppressed by syslog-ng on fevernas03 2020-12-27T02:10:49+08:00 fevernas03 scemd: polling_sys_thermal.c:35 ioctl device failed 2020-12-27T02:10:49+08:00 fevernas03 scemd: polling_sy
  6. Hi, I cannot get my HDD hibernated. May I confirm with you that the only change to the system is to amend the 3rd line of that file? (as you commented the orginal 3rd line with # then added a new line to point the logs to /dev/null?) My config: DS3615xs, DSM 6.2.3-25426-U2 & U3, extra.lzma v0.11_test. I have amended that line and reboot. U see the /var/log/scemd.log is keep on growing. The HDDs are not willing to sleep at all. Keep spinning.... Thank you in advance!
  7. Sorry IG-88 please ignore the above post. Just got the CSM enabled and now the RTL8111H can get the IP. Thanks a lot! Also, may I ask if jun's loader v1.04b 918+ support MPT HBA? My is LSI_SAS2308_LSI-9207-8i (HP220). Thanks a lot!
  8. Hi IG-88, thanks for your advise! Still trying to figure out how to enable CSM mode from my Biostar A68N-5455 as the manual doesn't has such option. Also, may I ask if jun's loader v1.04b 918+ support MPT HBA? My is LSI_SAS2308_LSI-9207-8i (HP220). Thanks a lot!
  9. Hi, I am using 3615xs v1.03b loader with my motherboard but the on-board 8111H cannot get any IP. Can you help to advise what was wrong? 1) my motherboard is Biostar A68N-5545. It uses AMD CPU so I chose 3615xs v1.03b loader 2) Tried the 3 extra.lzma for loader 1.03b ds3615 (original, v0.5, v0.11_test) All 3 extra.lzma cannot get any IP from router. Router cannot see this motherboard is in network. Please help. Thanks a lot!
  10. I saw DSM 6.2.3-25426 Update 3 was out. Is this issue fixed by official DSM? Thanks a lot!
  11. Hi @richv31, thanks a lot! Will you know which partition that needed to be deleted? Any guide I can follow? I worry about data lost so much. I only found another guide which is quite diff: https://xpenology.com/forum/topic/12778-tutorial-how-to-downgrade-from-62-to-61-recovering-a-bricked-system/ Thanks a lot!
  12. I need to get the HDD hibernation working again as HDD temperature is high in here. Is downgrade be the only method up to this point? If so, may I ask how an I downgrade back to DSM 6.2 with all my data preserved? Thanks a lot!
  13. after suppressing the scemd.log, then the 3 error message will be logged into /var/log/messages
  14. Hi @richv31, is it any WRITE action to /var/log will stop the HDD hibernation? May I ask where is the hibernation log be stored in DSM? I told some time to test it. I turned it on at 23:00 last night and then let it idle. Then SSH login at 04:34 and I found the log activities like this: drwxr-xr-x 2 root root 4096 Aug 20 20:20 disk-latency drwxr-xr-x 17 root root 4096 Aug 20 23:01 .. -rw-rw---- 1 system log 1917 Aug 20 23:01 apparmor.log -rw-rw-rw- 1 root root 2269 Aug 20 23:01 space_operation_error.log -rw-rw---- 1 system log 2391 Aug 20 23:02 datascrubbi
  15. Hi @richv31, I have got the ioctl error suppressed from scemd.log with great help from flyride. However I found that HDD hibernation is still not working as before. Would you have further advise on this? Thanks a lot!