Gronaldo
-
Posts
90 -
Joined
-
Last visited
-
Days Won
3
Everything posted by Gronaldo
-
Both. I use load balancing. Both ports are identical, i belive.
-
I use a G5400 with 8GB RAM. Buid details
-
Just completed a new build, using an Asrock H370M-ITX board and 1.04b loader / DSM 6.2.2-24922, all fully functioning without any hassle or additional drivers. With 6 onboard SATA ports and 2 Intel NICs this is an ITX board to recommend.
-
Sorry, don't have this unit anymore. Can't share much info as such. Was a new setup, no upgrade. Standard extra.lzma. HW acceleration not tested. Did fiddle a lot with it, some unexpected and inconsistent behaviours, so when i had a chance to sell it...i did.
-
Just tried this, see my posts above. Answer is No. This is Broadcom based, while you need Intel based.
-
Pfff...it is running now. After some tests, I updated my 6.1.7 version to manual 6.2.1 PAT, using the Intel server network card. It took machine more time than usual to become available again. I almost gave up and pull the plug... In the end machine rebooted a second time, while Assistant show 'Starting services'. After finally completing all, it now runs with upgrade 4, much to my surprise. But anyway, we're in business again! Thanks!
-
Thanks, I'll give that a try! Did come accross overview, but did not pick up this detail
-
Not in last attempts. Installed new network card, under 6.1.7, all okay. Then 1.03b loader and DS3617 PAT. Tried 3615 earlier, but without Intel network cards. Also no luck.
-
For some reason I cannot upgrade my Microserver G8 to 6.2.1, using loader 1.03b. I installed a Intel based Hp NC360T dual network card, disabling the onboard ones. Tried to manually upload .PAT files etc. However unit dissapears after migrate / repairs actions. No clues anymore. Could it be my processor, being an i3-3240T?
-
Just installed this 1.04b loader for DS918+ on Gigabyte GA-J3455N-D3H board, without apparent issues. Did notice no info is displayed at all on monitor output, not even nromal Xpenology boot menu. Is this as intended? Is DS918+ image now adviced for J3455 platforms? Feedback / comments welcome.
-
After more testing I found a reboot is required in order to work. Machine is usually off and active for making backups, as target for live Nas and creating secondary backup to USB drive. So after initial boot, no USB drive is detected, even after reconnecting a few times. After reboot, with drive connected, is works. Any suggestions how to resolve or what issue may be? Thanks for any assistance . -
For a long time I am using a Seagate USB 3.0 drive for external backups. It seems starting with DSM 6.1.7-15284 the drive is no longer recognised. Test with other USB 3.0 drives have same results. On USB 2.0 all drives do work. I am using same hardware, same loader (Jun v.1.02b) as before, when all worked without any issues. Anybody any suggestions how to fix this? Many thanks!
-
Thanks, will take a look. Funny thing is; - Working bootdisks (created earlier or newly in VM with Win1703) cannot be read correctly - Same issues at 3 different PC's (new install 1709 or upgraded earlier versions) - Not USB drive dependent, preparation or partioning done as usual - Used to be able to read bootdisk and edit config files directly, not posible anymore, besides on older Win versions. Very strange....
-
Sure? Releases
-
All, after the Windows 1709 update I cannot successfully create or read the USB bootdisk loader, using Win32Imager 1.0. Somehow Windows seems to limit access to the USB device and partitions. Using a previous version of Windows, 1703, even as a VM on the same PC, works all fine. So i found my workaround, but i am surprised not to see any similar issues reported here?
-
Strange problem after Win10 (1709) update
Gronaldo replied to ZaFord's question in Answered Questions
After the 1709 update I cannot create or read the USB bootdisk loader, downgrading to 1703 works fine again. I use Win32imager and used to edit config files on desktop, after creating the USB stick. Still investigating what's going on, but any suggestions are welcome. -
Duct tape, permanent marker, curtain.....
-
Hard Disk Numbering VS Motherboard port numbers
Gronaldo replied to dgrigo's question in General Questions
I can confirm there can be a difference in mainbord and DSM ports. Seen this on at least 3 boards. Serial number is best to check. Asrock C70M1 is an example. -
No luck. Issue persists.
-
Hm..other build have the same update available, but do not open control panel. Will investigate further along suggested lines.
-
On one of my 6.02 builds, suddenly the Control Panel opens on every login. Tried to toggle disable Resume option on personal settings a few times, without any luck... On another identical build all works well. Both updates from5.2 to DSM 6.0.2-8451 Update 1, using Jun's v1.01 loader. It is just annoying, not serious
-
[SOLVED] HP Proliant N40L MicroServer native support
Gronaldo replied to jnus's topic in DSM 5.2 and earlier (Legacy)
Just remove completely. -
Strange.... No other optional packages installed, could it be missing any supporting files?
-
Appreciate your initiative and help, but for now I'm reverting back to power off by web portal.
-
Details as requested. Box 1; AMD C-70, ASRock C70M1, Corsair ValueSelect 4GB DDR3-1333 CL9, 2xWestern Digital Green 2TB Box 2; AMD A4-5300, ASRock FM2A88M-HD+, Corsair XMS 4GB DDR3-1333 CL8 kit, 2x Western Digital Green 2TB, 2x Western Digital Red 2TB So both are AMD based... Attempts to Stop or Remove package resulted in rotating wait indicator. No responce at all anymore, also not able to close Package Center. Hard reset needed.
